Home > Auto diversen > Krikken > Clarke Krikken > Clarke CTJ 3000LS Krik

Handleiding Clarke CTJ 3000LS Krik

Handleiding voor je Clarke CTJ 3000LS Krik nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

SAFETY PRECAUTIONS

1. ALWAYS inspect the jack before use. Ensure that all parts are in good condition and

operating smoothly, the wheels are sound and that no cracks or distortion is apparent.

If in doubt do not use. Have the parts replaced or consult your CLARKE dealer.

2. ALWAYS ensure the jack is on a firm solid base, and that there is no likelihood of it slipping

when under load.

3. ALWAYS ensure the load is taken by the FULL saddle and that the point of lift on the load,

is of sufficient strength to support the full load adequately.

4. ALWAYS ensure that the load is stabilised or supported in such a way that it will not shift

during lifting or lowering operations.

5. ALWAYS use supports to stabilise the load once lifted. NEVER work on or under a load unless it

is fully and adequately supported. NEVER rely upon the jack to hold the load in position.

6. ALWAYS ensure that all personnel are well clear of a load being raised, or lowered.

7. NEVER push a load off the jack.

8. NEVER exceed the rated load for the jack (see ‘Specifications’).

9. NEVER use if an oil leak is apparent...Consult your Clarke dealer.

10. NEVER attempt to disassemble the jack. Consult you CLARKE dealer if problems arise

11. NEVER move a load using the jack as a dolly. This jack is for lifting ONLY..

ASSEMBLY

IMPORTANT! BEFORE assembly, it is

important to remove the plastic retainer,

which, for transit purposes, holds down

the main operating arm (see Fig.1). To

do this, press and hold down the arm,

against spring pressure, pull out the

retainer, and gently allow the arm to

rise.

Unscrew the bolt, at the rear of the jack

handle housing, sufficient for the

handle to be inserted.

Ensure the square drive on the end of the handle, engages fully with the square spigot within

the housing, before retightening the securing bolt

OPERATION

RAISING A LOAD

Ensure the load is chocked and stable and on firm level ground, before manoeuvring the

jack so that the saddle is directly beneath the lifting point. Consult the vehicle handbook to

determine the correct lifting points.

Turn the knob, at the top of the handle, fully clockwise and pump the handle to raise the

saddle, As it meets the lifting point, check to ensure it is in full contact and there is no

obstacle to prevent a clean lift, before proceeding to pump the handle further to raise the

load. UNDER NO CIRCUMSTANCES attempt to move the load whilst supported by the jack.

NOTE: Models CTJ2QLG and CTJ3QLG are provided with a quick lift pedal. This may be used

to bring the saddle to the lifting point in one quick operation, but NOT TO RAISE THE LOAD.

Place axle stands or suitable supports beneath the vehicle, before VERY GENTLY turning the

knob anticlockwise. This action will open the release valve to lower the load on to the stands.

DO NOT jerk the handle...ensure it lowers under complete control on to the axle stands

which must be correctly positioned and take the weight evenly.

LOWERING A LOAD

First jack up the load in order to clear the axle stands or supports, then, when the supports

have been removed, check to ensure that there are no obstacles that could prevent the

oad from lowering without hindrance, and that all personnel are well away from the site.

VERY GENTLY turn the Knob anticlockwise and the load will lower. DO NOT jerk the

handle....lower the load under complete control....DO NOT allow it to lower too quickly as

this could damage the pump seals

MAINTENANCE

Daily.

Inspect for distortion of components, and security of all nuts and bolts. If in doubt, do not use.

Have damaged parts repaired or replaced. If necessary, consult your CLARKE dealer.

Monthly

1. Oil all joints, linkages, the pump roller and front wheel hubs.

2. With a grease gun, grease the lift arm pivot at the grease nipple provided.

3. Apply grease to the caster bearings.

NOTE: Lubrication and cleanliness is important as dirt, rust etc can cause a jerky action which

could damage internal components.

Every 6 months

Carry out a thorough inspection for serviceability of components and check for oil leaks.

Only a very slight oil seepage is permissible. If a leak is evident, take the jack out of service,

and consult your CLARKE dealer.

Annually

Check the ram oil level as follows:

1. Ensure the ram is fully retracted by turning the Handle fully anticlockwise.

2. Remove the cover plate, where fitted, located at the base of the handle housing, to

gain access the ram, then remove the ram filler plug.

3. Lift the jack so that it is vertical, resting on its front wheels and check the oil level. It should

be level with the bottom of the oil filler hole.

If necessary, top up with CLARKE HYDRAULIC OIL ONLY. (See your CLARKE dealer.

Quote Part No. 3050830 for 1 litre bottle 3050835 for 5 litres.)

4. Replace filler plug and purge system of air.....see below.

Storage

Store in a dry place where it cannot be attacked by the elements with the ram in its fully

retracted position. If stored for long periods, inspect at least twice a year, clean and re-oil.

For servicing, contact your CLARKE dealer, or CLARKE International Service Dep’t.

Beoordeling

Laat ons weten wat je van de Clarke CTJ 3000LS Krik vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de Clarke CTJ 3000LS Krik?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de Clarke CTJ 3000LS Krik. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Clarke CTJ 3000LS Krik. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Clarke. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Clarke CTJ 3000LS Krik in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.