Handleiding Eureka Copper Canyon 1610 Tent

Handleiding

fig 13

Component List: 1 Tent Body, 6 Wall Poles, 3 Roof Poles, 2 Brim Rods,

1 Fly with Guy Ropes, 1 Carry Bag, 1 Stake Bag/Stakes, 1 Pole Bag

2. Assemble the shock

corded poles and divide

according to size and shape.

Take care; make sure that

each pole section is fully

seated into the next. Do not

allow the sections to snap

together as this can damage

the ends. See fig 2.

1. Remove from the carry bag and separate all the components. Unroll and unfold the

tent fabric with the top side up, on a clean, dry space and open the doors. If windy,

stake down the windward corner. This is a large tent, you will need two people for

set-up. See fig 1.

4. Raise the tent. Start on one end and insert

black wall poles into the corner elbows. At

the bottom of each pole, insert the pin/ring

(attached to the corner web) into the

bottom of each pole. Repeat on the other

end. Next, install the tan poles at the

center. With the tans, it works best to insert

the ring/pin first and then fit the pole into

the elbow. See fig 6, 7 & 8.

Repeat on the other side until the tent is at

full height and freestanding.

5. Attach all clips to the wall poles. See fig 9.

6. Stake the tent down through the web loops.

Stake opposite corners while applying tension to

smooth the floor wrinkles. Next, align the center

poles and stake down. Do this before you add the

fly. See fig 10 & 11.

Take Down: Pull up all stakes. Release the fly’s hook & loop straps and J-hooks.

Remove fly. Remove clips from wall poles and pull poles off of the pins.

Remove roof poles. Collapse all poles and stow. Fold the tent onto itself then

fold the fly and lay it on tent. Roll up both towards an open door and stow.

Options: Floor Saver- med. square, Gear Lofts- A & F, and a 120v Rope Light

7. Attach the fly to the tent. Turn the fly right side up and orient

it along the length of the tent. Grasp two corners of the of the

fly and drag them up and over the roof to completely cover the

tent. (This is much easier with two people.) The brim rod

sleeves should hang out over the tent ends. At the wall poles,

reach under the fly and attach the hook & loop straps to the

poles just below the elbow and down the length of the poles,

securing the fly in place. See fig 12.

8. Attach the brim rods. At

one end of the tent, reach

under the fly and slide an

assembled brim rod

through the sleeve. See fig

13. Locate the grommets at

the corner of the tent and

insert the tips of the brim

rods into these grommets.

Repeat at other end. See

fig 14.

Assembly Instructions for

Copper Canyon 1610

C

B

A

E

F

D

fig 2

fig 1

fig 3

fig 5

fig 6

fig 11

fig 12

fig 15

fig 14

fig 16

fig 17

fig 7fig 8

fig 9

fig 10

3. Insert the roof poles. Slide both black roof poles into their sleeves sewn on the tent

body. They should run from corner to corner crossing in the center. The sleeves are color

coded with black trim. Fit one end of each into a nylon elbow attached to the roof corners

at A and B. Move to the opposite side, arch the poles and again fit into the nylon elbows

at C and D. Insert the gray roof pole, front to back

, into the remaining sleeves and over

the two black poles. Fit the gray poles into the elbows at E and F. See fig 3, 4 & 5.

REV. B 4.09

NOTE: One arm of

each center elbow

has interior ribs.

The gray roof poles

insert into the

ribbed arms. Wall

poles insert into

the plain arms.

fig 4

9. Attach the shock corded J-hooks from the fly to the nylon

rings on the webs at the bottom of the poles. See fig 15.

10. Guy out the tent.

This tent has very large straight walls that

act differently in high winds. There are pre-attached guy out

ropes in the pockets on the fly at the top of each pole. Stake

out the ropes and adjust tension with the sliders. Additional guy

out instructions on the back side of this sheet. See fig 16.

11. Tent door has “Sweep Out” feature. Stake the web loop

(inside the door) to the ground to easily whisk dirt out of the

tent. See fig 17.

Brim Rods

Center

Wall poles

Corner

Wall poles

Roof poles

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Eureka Copper Canyon 1610 Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Eureka. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Eureka Copper Canyon 1610 Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Eureka Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Eureka Copper Canyon 1610 Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Eureka Apex XT Tent

Handleiding

Eureka Scenic Pass 2XT Tent

Handleiding

Eureka Zeus Classic Tent

Handleiding

Eureka Down Range 2 Tent

Handleiding

Eureka Amari Pass 3 Tent

Handleiding

Eureka Suite 6 Tent

Handleiding

Eureka Timberline Tent

Handleiding

Eureka Tundern Cove 4 Tent

Gerelateerde categorieën