Handleiding Eureka N!ergy 1210 Tent

Handleiding

Assembly Instructions

for the N!ergy 1210 Tent

A

B

A

B

D

C

fig 1

tent poles

fly poles

fig 8

fig 2

fig 5

Component List:

1 Tent 2 Tent Poles 1 Carry Bag

1 Stake Bag W/Stakes 1 Rain Fly

2 Fly Poles 1 Pole Bag 6 Pull Out Cords

1 Gear Loft 1 Divider

1. Unroll and unfold the tent on the ground. Separate the rest of the

components and place to one side. Open the door before pitching the

tent. Do not stake the tent down (however, in windy conditions, stake

down one corner that faces into the wind).

2. Assemble all of the shockcorded poles. Keep the end sections from

snapping together, as this can damage the ends. Make certain each

plain end has been properly seated into the metal ferrule.

3. Insert an assembled pole

through both sleeves from A to

B. Insert the second pole through

the sleeves from C to D, forming

an X across the tent. See fig 1.

There is a fabric loop at the tent’s

peak. Capture this loop with the

top pole as you move through

the sleeves. See fig 1 & 2.

4. At A, insert the web corner pin into the end of the

tent pole ferrule. At B, grasp the tent corner pin in one

hand, the tent pole in the other. Arch the pole and

place the pin into the end of the pole. See Fig 3 & 4.

Repeat this with the second pole from C to D raising the

tent as you go. See fig 5.

5. Start at the bottom and attach all the clips to

the poles to create a freestanding tent. Place it in

the desired location. See fig 6.

6. Stake the tent down through the

corner loops. Stake the opposite corners

while applying tension to smooth the

floor wrinkles.

Also, stake out the beckett

beneath each of the side windows.

See

fig 7 & 8.

7. Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front of

the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to side

down the center of the fly forming an X. Secure the fly to the poles by wrapping the hook &

loop fastener around the fly poles. See fig 9, 10 and 11.

8.

Attach the fly to the tent

. Turn the fly assembly over and align it so

that the poles point out over the doors. Grasp the corners of the of the

fly and drag them up and over the roof to completely cover the tent.

(This is much easier with two people)

At the corners of the tent, reach under the fly and attach the hook & loop

straps to the tent poles, securing the fly in place. See fig 12.

At the bottom/corners of the tent, attach the shockcorded J-hooks to the

rings on the corner webs. See fig 13.

9.

Tie a guy rope

to each of the 4

rings attached to the fly and stake

out. Adjust tension with the in-line

sliders. See fig 14 & 15.

YOUR TENT IS READY !

fig 4

fig 9

fig 10

fig 11

fig 7

fig 6

fig 12

fig 13

fig 15

fig 14

REV D 4.09

NOTE:

• Although it is possible to pitch this tent alone, it is faster/easier with two

people.

• Do not drop tent bag or pole bag on its end. Do not bounce tent bag on

its end to get the tent out. These actions may cut the shockcord and/or

damage the pole ends.

• The N!ergy series tents are pre-wired with three 12V outlets. Take care

to keep them in their sleeves and avoid stepping on the sockets and

wires during assembly.

fig 17

green

blue

fig 16

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold separately. Once connected to

power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16.

E! Power Port: Open zipper and run extension cord through opening.

Close zipper so that it rests next to the extension cord. Make sure the

zipper cover is not twisted or tucked. The cover must lay flat against

the outside of the tent to keep out rain.

Accessories: E! Power Fan/Light, E! Power Reading Light and an E!

Power 12v Adapter Cord.

Sweep Out: Inside, at the bottom of the door is a sewn-in web loop. Pull

this loop to the outside and stake it down to provide a ready exit for

floor sweepings. See fig 17.

Take Down: Pull up all stakes. Release the fly’s hook & loop straps. Remove fly.

Remove fly poles. Remove clips from tent poles and pull poles off of the pins.

Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it

on tent. Roll up both towards the open door and stow.

Read the important safety instructions on the reverse side.

fig 3

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Eureka N!ergy 1210 Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Eureka. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Eureka N!ergy 1210 Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Eureka Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Eureka N!ergy 1210 Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.