Handleiding Remington XR1395 Scheerapparaat

Handleiding

■ Ensure your skin is free of oils.

■ Wait at least 15 minutes after getting

up before shaving, to ensure your face

is free of puffiness that may be present

from sleeping.

■ Always hold the shaver at a right angle

to the skin so that all three heads are

touching the skin with equal pressure.

■ Stretch skin with the free hand so hairs

stand upright, making it easier for them

to enter the cutting chamber.

■ Use moderate to slow, circular stroking

movement.

■ The use of short, circular motions in

stubborn areas may obtain a closer shave,

especially along the neck and chin line.

■ Do not press hard against the skin to

avoid skin irritation and/or damage to the

rotary heads.

**We recommend that you use your

new shaver daily for up to four

weeks to allow time for your hair

and skin to become accustomed to

the new shaving system**

Before using, read the important

safety instructions in front of the

manual.

1. Plug power adaptor into charging stand.

(Dia A)

2. Place shaver into charging

stand. (Dia B)

3. Charge shaver for 24 hours

before its first use. Note:

During initial charge ignore

the electronic indicators as they are in

“start up cycle”. (Dia C)

4. Use shaver until

recharge is required.

IMPORTANT SAFETY

INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Charging

Setting Travel Lock

■ Always store this appliance and cord in

a moisture-free area. Do not store it in

temperatures exceeding 140°F (60°C).

■ Do not use this appliance with a

damaged or broken head or cutters, as

facial injury may occur.

■ The power unit is intended to be

correctly oriented in a vertical or floor

mount position.

■ Shavers, including the trimmer, are for

use on facial hair only. They should not

be used for shaving the hair on your

head or any other part of your body.

■ For additional protection the installation

of a residual current device (RDC) with

a rated residual operating current not

exceeding 30mA is advisable. Ask an

electrician for advice (Argentina/Chile).

When using an electrical appliance, basic

precautions should always be observed,

including the following. Read all instruc-

tions before using this shaver.

DANGER

To reduce the risk of fire or electric

shock, carefully follow these instruc-

tions:

■ Do not reach for an appliance that has

fallen into water. Unplug it immediately.

■ Detach the appliance from the power

supply cord before cleaning.

■ Except when charging, always unplug

this appliance from the electrical outlet

immediately after using.

■ Unplug this appliance before cleaning.

WARNING

To reduce the risk of burns, fire, electric

shock, or injury to persons:

■ An appliance should never be left

unattended when it’s plugged in, except

when charging a rechargeable appliance.

■ This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety.

■ Children should be supervised to ensure

they do not play with the appliance.

■ Use this appliance only for its intended

use as described in this manual. Do not

use attachments not recommended by

the manufacturer.

■ Never operate this appliance if it has

a damaged cord or plug or if it is not

working properly, if it has been dropped

or damaged, or if it has been dropped

into water.

■ Keep the cord away from heated

surfaces.

■ Never drop or insert any object into any

of the appliance’s openings.

■ Household use only.

■ Do not use outdoors or operate where

aerosol (spray) products are being used

or where oxygen is being administered.

■ Always attach the plug to the appliance,

then to the outlet. To disconnect, turn all

controls to OFF, then remove plug from

outlet. Detach removable power cords

from appliances for storage.

■ Do not plug or unplug this appliance

when your hands are wet.

■ The device must only be used with the

power unit supplied with the device.

■ Class III devices must establish that they

must only be supplied with a very low

safety voltage corresponding to the one

marked on the device.

■ For washable models that have supports

or bases, they must be installed so that

they can not fall into the water.

■ Do not use an extension cord or a

voltage converter with this appliance.

■ Do not wrap the cord around the

appliance.

Cleaning and Maintenance Performance Guarantee - See insert

© 2020 Spectrum Brands, Inc.

All rights reserved

® Registered Trademark and TM

Trademark of Spectrum Brands, Inc.

Spectrum Brands, Inc.

Middleton, WI 53562

10/20 Job#18818-01 T22-0001936-F

DESIGNED IN USA

MADE IN CHINA

XR-1430, XR-1395:

Electrical Characteristics

100-240V~, 50/60Hz 200mA

This warranty shall not be valid

where it is contrary to U.S. and

other applicable laws, or where the

warranty would be prohibited under

any economic sanctions, export control

laws, embargos, or other restrictive

trade measures enforced by the United

States or other applicable jurisdictions.

This includes, without limitation, any

warranty claims implicating parties

from, or otherwise located in, Cuba,

Iran, North Korea, Syria and the disputed

Crimea region.

Feature XR-1430 XR-1395

Power System

Lithium

Rechargeable

Lithium

Rechargeable

Full Charge Time

4 hours 90 minutes

Cordless Shave Time

50 minutes 60 minutes

Quick Charge

No Yes

Indicators

Charging/Low

Battery

Runtime

Gauge

Voltage Type

Worldwide Worldwide

Replacemnt Part

SPRXR SPRXR

Wet/Dry

Yes Yes

Use with gel or

foam in the shower

for ultimate comfort.

Shaving

Shaving Tips (In Shower With Gel or Foam)

Shaving Tips (Dry)

The shaver is a wet/dry appliance. The shaver may be

cleaned under warm water.

Cleaning & Care

NOTE: **When cleaning your shaver,

make sure the shaver is turned off

and disconnected from the power

cord.**

CAUTION!

■

To clean the external surfaces of the

shaver, use a damp cloth. Do not use

strong detergents or other chemicals.

■ To dry, wipe the surface of the shaver

with a dry towel. Do not use a hair dryer

or heater to dry the shaver.

■ If you use shave foam or gel with your

shaver, it is important to open and rinse

the head of your shaver thoroughly after

each use to avoid dried gels or foam

from clogging the cutters and hindering

shave performance.

Daily:

1. Pull rotary head face of shaver off of

lower hairpocket. (Dia G)

2. Tap out excess hair shavings. (Dia H)

3. Rinse the head of the shaver in running

water. (Dia L)

4. Close head assembly. (Dia P)

Weekly:

1. Perform the daily cleaning steps 1 and 2.

2. Remove the cover from the hair pocket

assembly. (Dia G) Place the body of the

shaver aside to ensure that it will not

get wet.

3. Release the inner cutter lock by sliding

out of support. (Dia I)

4. Remove the inner cutter carrier away

from the cutters. (Dia J)

5. Remove the cutters. (Dia K)

6. Thoroughly rinse away any debris from

inner and outer cutters. (Dia L)

7. Replace the inner cutters. (Dia M)

8. Place inner cutter lock back into position

by sliding it back into the support until it

snaps into place. For best performance,

match color coded hubs on cutters.

(Dia N, O)

9. Lubricate each cutter with household oil.

10. Snap head assembly back onto neck/hair

pocket. (Dia P)

** Trimmer: Lubricate teeth with oil every

six months.

When your rechargeable shaver reach-

es the end of its useful life, the LiFePO

4

batteries must be removed from the

shaver and be recycled or disposed of

properly in accordance with your state

and local requirements. If this is not

required by law, you may elect to dis-

pose of the shaver with the batteries.

CAUTION! Do not put in fire or muti-

late your batteries when disposing

as they may burst and release toxic

materials. Do not short circuit as it may

cause burns. Dispose of properly in

accordance with your local and state

requirements.

To Remove the Rechargeable Battery:

1. Unplug the shaver.

2. Run shaver until the motor stops.

3. Remove the head from the shaver (Pull

head up and off).

4. Using a small screwdriver, pry the ‘collar’

off of the top of the handle.

5. Using a small screwdriver, pry the front

cover from the body.

6. Remove three screws located on front of

shaver.

7. Using a small screw driver, pry up the

newly unsecured inner housing to expose

the battery.

8. Pry battery free from

circuit board. (Dia Q, R)

9. Dispose of battery

properly.

Battery Removal

This shaver is a wet/dry appliance, the hand-held

part of which may be used in a bath or shower.

H

G

P

J

K

L

M

N

I

O

Model XR-1395 has an interchangeable

triple rotary shaving head and beard

grooming head.

To remove the attachments

1. Grasp the shaver handle in one hand

and with the other hand grip the cutting

head with your fingers.

2. Pull the attachment

straight up and off the

handle. It will require a

firm but minimal force

to separate the snap fit.

(Dia F)

To insert the attachments

1. Note the hexagon shape of the

attachment coupling has a point on the

top and bottom.

2. Align the shapes of the handle and

attachment couplings.

3. Press the attachment head into the

handle. The attachment will snap into

place securely.

4. Proper orientation of the rotary shaver

head is to have two rotary cutters at the

top of the handle.

5. Proper orientation of the groomer

attachment is to have the grooming

blades toward the top of the handle.

Beard Groomer Comb attachment

1. The beard groomer attachment has an

adjustable comb.

2. The beard groomer can be used without

the adjustable comb to cut to a length

of .5mm or to trim sideburns and beard

edges.

3. The adjustable comb has five settings to

provide hair cut at lengths from 1 mm to

5 mm.

4. Attach the comb to the groomer head

by hinging the front of the comb at the

groomer cutting blade edge and then

rotating it down to snap onto the top of

the groomer.

5. To adjust the comb cutting lengths,

press the small black button at the back

of the comb attachment in slightly and

then rotate to the left or right to move

the comb position.

6. Note the small white number at the top

of the comb will indicate the cutting

length.

7. Release the button to lock the comb in

the desired position.

8. During use, hold the comb against your

skin and move through your beard to cut

to the desired length.

Interchangeable Heads

A

D

B

E

CA

B

Travel Lock feature

Model XR-1395 are equipped

with a Travel Lock feature, intended

to prevent the shaver from turning

on and discharging accidently while

packed in luggage.

To set the travel lock:

1. Depress and hold the on switch for 3

seconds. The shaver will turn on, then

will shut off after the 3 seconds. The LED

display will flash five times to indicate

the lock is set.

2. While the travel lock is set, if the on

switch is pressed, the LED display will

flash three times to indicate the shaver

is in travel lock mode.

To unlock the travel lock:

1. Depress and hold the on switch for 3

seconds. The LED display will flash three

times while the button is being held and

then the shaver will turn on.

Quick Charge

Shaver will charge long enough for one shave in 5 minutes.

Voltage Type

Worldwide Voltage – shaver automatically adapts to an outlet voltage between 100V or

240V, depending on the country where the product was sold.

1. Press power button to turn on. (Dia D)

2. Shave face and neck using short, circular

strokes. (Dia E)

**For optimal results, shave with gel in

shower.

1. While in shower, wet face.

2. Apply shave gel or foam to applicable shaving area.

3. Shave face and neck using short, circular strokes.

4. When finished shaving, rinse face.

5. Follow cleaning and care instructions.

F

R

Q

XR series

For shavers equipped with a quick

charge:

A 5 minute quick charge will allow for

3 minutes of shaving.

CAUTION!

■

Make sure the shaver and your hands

are dry when charging the shaver.

■ Always charge the shaver in a cool,

dry place.

Cleaning Brush

1. Add a drop of facial cleanser to the brush

head and place under the shower.

2. Press the On / Off button to turn on.

3. Divide the face into 4 main sections:

forehead, nose and chin, left cheek, and

right cheek.

4. While applying the product on the face,

press gently. Move the rotating brush

with circular movements over each

section for about 30 seconds.

Use and Care Guide

1. ActiveContour™ XL Head Flex

2. HYPERFlex™ neck suspension

3. PrecisionPlus™ Heads

4. On/Off Button

5. Battery Display

6. Pop-up Trimmer

7. Power port charge pins

8. Charging stand

9. Adaptor

10. Trimmer Head (only XR-1395)

11. Cleaning Brush (only XR-1395)

SHAVER PARTS

1

2

3

4

7

5

6

XR-1430 XR-1395

9

10

8

11

8

For digital manual,visit www.remingtonlatam.com

SKU: XR1395 (BV) A, XR1430 (BV) F, XR1430 (BV) R, XR1430 (BV) A

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Remington XR1395 Scheerapparaat. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Remington. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Remington XR1395 Scheerapparaat in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Remington Scheerapparaten
Meer handleidingen voor Scheerapparaten

Veelgestelde vragen over Remington XR1395 Scheerapparaat

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Remington XR1790 Scheerapparaat

Handleiding

Remington MSC100 MicroScreen Compact Scheerapparaat

Handleiding

Remington R4130 Pivot & Flex Scheerapparaat

Handleiding

Remington MS3-3500 MicroScreen 3 Scheerapparaat

Handleiding

Remington WSF5060 Scheerapparaat

Handleiding

Remington WSF100 Scheerapparaat

Handleiding

Remington TF70 Travel Scheerapparaat

Handleiding

Remington XR1530 Ultimate Series Scheerapparaat

Gerelateerde categorieën