Home > Diversen > Drones > Blade Drones > Blade Inductrix FPV Drone

Handleiding Blade Inductrix FPV Drone

Handleiding voor je Blade Inductrix FPV Drone nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

3. Attach the fpv monitor holder to the MLP4DSM

transmitter.

a. Slide the holder down over the antenna.

b. Tighten the clamp screw. Do not overtighten.

c. Open the clamp jaws and place the monitor in the

jaws. The angle of the monitor can be adjusted by

loosening the angle adjustment knob, rotating the

clamp up or down and tightening the adjustment knob.

NOTICE: Consult local laws and ordinances before operating FPV (ﬁ rst person view) equipment.

In some areas, FPV operation may be limited or prohibited. You are responsible for operating this

product in a legal and responsible manner.

FPV RTF/BNF

Instruction Manual / Bedienungsanleitung / Manuel d’utilisation / Manuale di Istruzioni

Age Recommendation: Not for children under 14 years. This is not a toy.

Charging Warnings

WARNING: Failure to comply with the

following warnings could result in product

malfunction, electrical issues, excessive heat,

FIRE, and ultimately injury and property damage.

• NEVER LEAVE CHARGING BATTERIES

UNATTENDED.

• NEVER CHARGE BATTERIES OVERNIGHT.

• Never charge damaged batteries. If the battery

begins to swell during charging or use, discontinue

immediately.

• Always use the included battery and charger.

Disconnect the battery after charging.

• Charge batteries away from ﬂ ammable materials

in a well-ventelated area.

• Never charge, transport, or store batteries in hot,

cold, or very sunny places

(recommended between 40–120° F or 5–49° C).

Specifications

Length

3.26 in (83mm)

Propeller Diameter

2.56 in (65mm)

Height

1.10 in (28mm)

Flying Weight

.85 oz (24 g)

Install 4 AA batteries into the transmitter, noting

polarity. Replace the transmitter batteries when the

power LED ﬂ ashes and the transmitter beeps.

We recommend using only alkaline AA batteries

in the transmitter, however, it is possible to use

rechargeable NiMH batteries.

CAUTION: If using rechargeable batter-

ies, charge only rechargeable batteries.

Charging non-rechargeable batteries may cause

the batteries to burst, resulting in injury to

persons and/or damage to property.

Charge the Flight Battery

Install the Transmitter Batteries (RTF)

Transmitter and Receiver Binding

NOTICE: Inspect the battery to make sure it is not damaged e.g., swollen, bent, broken or

punctured. Charge only batteries that are cool to the touch and are not damaged.

Insert the charger into a USB port.

Connect the battery to the charger.

CHARGING (Solid Red LED)

MAX CHARGE (LED OFF )

Disconnect the ﬂ ight battery from the charger immediately upon completion of charging.

CAUTION: Only use chargers speciﬁ cally designed to charge the included Li-Po battery.

Failure to do so could result in ﬁ re, causing injury or property damage.

CAUTION: Never exceed the recommended charge rate.

CAUTION: Once charging is complete, immediately remove the battery.

Never leave a battery connected to the charger.

Install the Flight Battery

BNF

Transmitter

If you are using a computer transmitter, in the channel input menu, set channel 6 (Aux1) to a momentary

switch such as the bind button (I). Set the model type to “Acro” or “Airplane” mode. Bind the quadcopter

to your transmitter following the directions below.

General Binding Procedure (BNF

)

1. Disconnect the ﬂ ight battery from the quadcopter.

2. Set the model type in your transmitter settings to “Acro” mode.

3. Center all trims on your transmitter.

4. Power off the transmitter and fully lower the throttle.

5. Connect the ﬂ ight battery in the quadcopter. The LED on the 3-in-1 control unit ﬂ ashes red

during initialization, then ﬂ ashes blue when it is ready to bind.

6. Put the transmitter into bind mode while powering on the transmitter.

7. Release the bind button/switch after 2–3 seconds. The quadcopter is bound when the blue LED

on the 3-in-1 control unit turns solid.

8. Disconnect the ﬂ ight battery and power the transmitter off.

MLP4DSM Binding Procedure (RTF)

1. Disconnect the ﬂ ight battery from the quadcopter.

2. Center all trims on your transmitter.

3. Power off the transmitter and fully lower the throttle.

4. Connect the ﬂ ight battery in the quadcopter. The LED on the 3-in-1 control unit ﬂ ashes red during

initialization, then ﬂ ashes blue when it is ready to bind.

5. When the blue light is ﬂ ashing, push in and hold down the left stick while powering on the trans-

mitter (you will hear a ‘click’ and a long tone).

6. Release the left stick. The transmitter will beep and the power LED will blink. The quadcopter is

bound when the blue LED on the 3-in-1 control unit turns solid.

7. Disconnect the ﬂ ight battery and power the transmitter off.

If you encounter problems, obey the binding instructions and refer to the troubleshooting guide for

other instructions. If needed, contact the appropriate Horizon Product Support ofﬁ ce. For a list of

compatible DSM

transmitters, please visit www.bindnﬂ y.com.

CAUTION: Always disconnect the Li-Po battery from the aircraft

when not ﬂ ying to avoid over-discharging the battery. Batteries

discharged to a voltage lower than the lowest approved voltage may

become damaged, resulting in loss of performance and potential ﬁ re

when the batteries are charged.

Throttle down

Power ON

Transmitter Control (RTF)

A B C D E F

Mode

Aileron (Left/Right)

Throttle (Up/Down)

Throttle

Trim

Aileron

Trim

Rudder

Trim

Elevator

Trim

Rudder (Left/Right)

Elevator (Up/Down)

Mode

Aileron (Left/Right)

Elevator (Up/Down)

Elevator

Trim

Aileron

Trim

Rudder

Trim

Throttle

Trim

Rudder (Left/Right)

Throttle (Up/Down)

Operating Safety Precautions

• As the user of this product, you are responsible for

operating it safely, not endangering yourself and others,

or damaging the product or the property of others.

• Operate your product in open spaces away from

people and property.

• Never operate your product with damaged electrical

components.

• Keep the transmitter powered on while model is

powered on.

• Let parts cool after use before touching, motors will

get hot in use.

• Remove batteries after use, as applicable.

General Product Safety Precautions

• Keep all batteries, chemicals, small parts and

anything electrical out of the reach of children.

• Avoid water exposure to this product. Keep parts dry.

• Keep moving parts clean.

The LEDs on the Inductrix indicate the front and back of the quadcopter. The white LEDs indicate the front.

The red LEDs indicate the back.

Takeo

Increase the throttle until the model is approximately 2 ft. (600mm) off the ground in a low-level hover and

concentrate on balancing the throttle stick’s position so that the quadcopter holds a steady hover altitude. In

some cases, you may need to make a few short “hops” to an altitude of just a few inches until you become

familiar with the control inputs and trim settings required to maintain a steady hover and altitude.

Hovering

The Inductrix quadcopter requires minor throttle adjustments to maintain its altitude in hover. Remem-

ber to keep these throttle adjustments as minimal as possible. Large adjustments could result in a

loss of control or a possible crash.

While attempting to establish a low-level hover, check to see if any trim adjustments are required to

help keep the quadcopter from constantly drifting in various directions. If you ﬁ nd that it constantly drifts

without any directional control input, land the model before making any adjustments to the trim settings.

• If the nose of the quadcopter rotates to the left or right, adjust the rudder trim.

• If the quadcopter continually drifts forward or backward, adjust the elevator trim.

• If the quadcopter continually drifts to the left or right, adjust the aileron trim.

Continue making minor trim adjustments until the machine hovers at a low altitude with very little

drifting and directional control input. If this is your ﬁ rst multicopter or helicopter, seek the help of an

experienced pilot to trim the model for you before making your ﬁ rst ﬂ ight.

With your quadcopter properly trimmed and maintaining a stable low-level hover, practice using the

rudder, elevator and aileron controls to familiarize yourself with the machine’s responses to control

inputs. Remember to keep the control inputs as minimal as possible.

Average ﬂ ight times are approximately 4 minutes.

NOTICE: Crash damage is not covered under warranty.

To prevent excessive wear to the motors, always allow the motors to cool between ﬂ ights.

Fly the Quadcopter

Low Voltage Cuto (LVC)

Video Monitor (RTF)

FPV Camera and Video Transmitter

Once the battery reaches 3V under load, the ESC will continuously lower power supplied to the motor

until complete shutdown occurs. This helps prevent over-discharge of the Li-Po battery. Land imme-

diately once the ESC activates LVC. Continuing to ﬂ y after LVC can damage the battery, cause a crash

or both. Crash damage and batteries damaged due to over-discharge are not covered under warranty.

Repeatedly ﬂ ying the aircraft until LVC activates will damage the ﬂ ight battery.

Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge.

During storage, make sure the battery charge does not fall below 3V per cell.

Dual rate

selection

Bind/

Flight Mode

Selection

Rate Selection – RTF

The Inductrix

RTF quadcopter comes with the Blade

MLP4DSM transmitter.

• When powered on, this transmitter is automatically high rate.

• Change rates by pressing and releasing the right control stick.

• In low-rate mode, the quadcopter is limited to a lower bank

angle and will self-level when the control sticks are released.

This mode is typically preferred by pilots looking for smoother/

easier control response during ﬁ rst time use.

• In high-rate mode, the quadcopter has a higer possible bank

angle and will self-level when the control sticks are released.

Flight Mode Selection

Cycle between the ﬂ ight modes by pressing and releasing the left stick of the MLP4DSM or by pressing and

releasing the momentary switch on your computer transmitter as programmed in the binding section above.

• S tability mode (blue LED): the bank angle is limited. When the sticks are released, the quadcop-

ter will return to level ﬂ ight.

• A gility mode (red LED): the quadcopter has no bank angle limits and will not return to level ﬁ ght if

the sticks are released. Use rates and expo to tune the performance according to your ﬂ ying style.

NOTICE: Do not attempt to change ﬂ ight modes while ﬂ ying with the MLP4DSM transmitter.

Attempting to do so will cause the transmitter to register a faulty center position. Always land the

quadcopter and release the sticks before changing ﬂ ight modes.

Dual rate selection

Aileron

Elevator

Rudder

Understand the Primary Flight Controls

If you are not familiar with the controls of your Inductrix quadcopter, take a few minutes to familiarize

yourself with them before attempting your ﬁ rst ﬂ ight.

Throttle

Aileron left

Aileron right

ForwardElevator down

Elevator up

Backward

Left Side View Left Side View

Rudder left

Rudder right

Nose Yaws Right

Nose Yaws Left

Throttle down

Throttle up

Left Side View Left Side View

Descend

Climb

Left

Rear View

Right

Rear View

Power LED indicator

USB Li-Po

Charger

EFLC1008

SOLID RED LED

–Charging

DC Input:5.0V 350mA

DC Output:4.2V 300mA

LED OFF

–Charge

Complete

Your RTF transmitter comes prebound to the Inductrix. If you need to re-bind, follow the directions below.

On/Off Switch

When pressed down, trim buttons make a sound that increases or decreases in pitch at each

pressing. The middle or neutral trim position is heard as a middle tone in the pitch range of the

sounds. The end of the control range is sounded by a series of beeps.

To receive product updates, special offers and more, register your product at www.bladehelis.com.

1. Before using the Spektrum

4.3 inch Video Monitor make sure the monitor is charged thoroughly.

Connect the micro USB connector to a 5V USB power source. The charge indicator LED will glow

red while charging and green when the monitor is fully charged.

2. Attach the included antenna to the antenna connector located on

the top of the monitor.

CAUTION: Do not power the monitor on without the antenna

attached. Doing so will damage the video transmitter and

receiver ampliﬁ ers. Ampliﬁ er damage is not covered by warranty.

5.8GHz Antenna connector

Menu Button:

Use the + and – buttons to modify:

Channel Selection Button

Single push to change channel

Frequency Band Button

Single push to change band

75%

AV In

Brightness

Contrast

Color

Mode (16:9, 4:3)

Language

Reset

1. Power on your radio transmitter, then power on the aircraft.

2. Power on the video receiver to make sure the channel is clear.

3. Select the desired video transmitter channel by pressing the

button on the quadcopter as shown to scroll through the

available bands (Fat Shark/IRC or Race) and channels (1-8).

Fatshark channel 1 is indicated by a red internal LED on the

quadcopter. Keep pressing and releasing the button to scroll

through the remaining channels.

4. Perform a range test before ﬂ ying.

If you experience static in the video feed, select a different channel.

NOTICE: The 25mW micro video transmitter range on your quadcopter is less than your ﬂ ight

control transmitter range. Ensure you have adequate video camera range for ﬁ lming.

Tip: If you are ﬂ ying with an FPV headset and are prone to motion sickness, sit in a chair. If you start to

suffer from motion sickness while ﬂ ying, lower your chin against your chest.

Fly in open areas, away from people, trees, cars, and buildings. The range of the system can be

impacted by any obstructions blocking your signal. It is normal to see break up in the video going

behind trees and other obstacles.

ON/Off Switch

Charge Status LED

Red = charging

Green = charged

5V Micro USB Charge Port

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product

before operating. Failure to operate the product correctly can result in damage to the product, personal

property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some

basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury

or damage to the product or other property. This product is not intended for use by children without direct

adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any

way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation and

maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly,

setup or use, in order to operate correctly and avoid damage or serious injury.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential

harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage

AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage

AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage,

collateral damage, and serious injury OR create a high probability of superﬁ cial injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole

discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and

click on the support tab for this product.

4. Turn on the monitor and look for a clear channel. Clear channels will have a consistent static background.

Channels with interference will display horizontal static lines. Select one of the clear channels. The video

transmitter included with the Inductrix FPV quadcopter transmits only on the Fat Shark/IRC and RaceBand

bands, channels 1-8.

5. Once you have chosen a clear channel on the monitor, select the same channel on the video transmitter.

BAND CH 1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8

Fat Shark/IRC 5740 5760 5780 5800 5820 5840 5860 5880

RaceBand 5658 5695 5732 5769 5806 5843 5880 5917

Band E 5705 5685 5665 5645 5885 5905 5925 5945

Band A 5865 5845 5825 5805 5785 5765 5745 5725

If you are operating this product in North America, you are required to have

an Amateur Radio (HAM) license. Visit www.arrl.org for more information.

Beoordeling

Laat ons weten wat je van de Blade Inductrix FPV Drone vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de Blade Inductrix FPV Drone?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de Blade Inductrix FPV Drone. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Blade Inductrix FPV Drone. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Blade. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Blade Inductrix FPV Drone in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.