Handleiding Conergy Q 85MU Zonnepaneel

Handleiding

Installation | Safety instructions | Maintenance

Photovoltaic modules user manual

Conergy S 175/180MU/Conergy Q 85MU

Purpose of this guide

This guide contains information regarding the installation and safe handling of

Conergy photovoltaic modules (hereafter referred to as "modules"). All

instructions should be read and understood before attempting installation. If there

are any questions, please contact your dealer or Conergy for further information.

The installer should conform to all safety precautions in the guide when installing

modules. Before installing a solar photovoltaic system, the installer should

become familiar with the mechanical and electrical requirements for photovoltaic

systems. Keep this guide in a safe place for future reference.

General

| Installing solar photovoltaic systems requires specialized skills and knowledge.

The installer assumes all risk of injury, including risk of electric shock. Module

installation should be performed only by qualified persons.

| All modules come with a permanently attached junction box and #12 AWG

(4 mm²) wire terminated in Multi Contact PV connectors. Your dealer can

provide additional extension cables to simplify module wiring.

| Each individual module can generate DC voltages greater than 30 volts (V)

when exposed to direct sunlight. Contact with a DC voltage of 30 V or more is

potentially hazardous. Exercise caution when wiring or handling modules

exposed to sunlight.

| When disconnecting wires connected to a photovoltaic module that is exposed

to sunlight, an electric arc may occur. Arcs can cause burns, start fires or

otherwise create safety problems. Exercise caution when disconnecting wiring

on modules exposed to sunlight.

| Photovoltaic solar modules convert light energy to direct-current electrical

energy, and are designed for outdoor use. Proper design of support structures

is the responsibility of the system designer and installer.

| Modules may be ground mounted, pole mounted, or mounted on rooftops.

Do not attempt to disassemble the module, and do

not remove any attached nameplates or components.

Doing so will void the warranty.

| Do not apply paint or adhesive to the module.

Do not use mirrors or other hardware to artificially

concentrate sunlight on the module.

| When installing modules, observe all applicable local, regional and national

codes and regulations. Obtain a building and/or electrical permit where required.

Safety precautions for installing a solar photovoltaic system

| Solar modules produce electrical energy when exposed to sunlight.

DC voltages may exceed 30V on a single exposed module.

| Only connect modules with the same rated output current in series.

If modules are connected in series, the total voltage is equal to the sum of

the individual module voltages.

| Only connect modules or series combinations of modules with the same

voltage in parallel. If modules are connected in parallel, the total current is

equal to the sum of individual module or series combination currents.

| Keep children well away from the system while transporting and installing

mechanical and electrical components.

| Completely cover all modules with an opaque material during installation to

prevent electricity from being generated.

Do not wear metallic rings, watchbands, ear, nose, or

lip rings or other metallic devices while installing or

troubleshooting photovoltaic systems.

Use appropriate safety equipment (insulated tools,

insulating gloves, etc) approved for use on electrical

installations.

| Observe the instructions and safety precautions for all other components

used in the system, including wiring and cables, connectors, DC-breakers,

mounting hardware, inverters, etc.

| Use only equipment, connectors, wiring and mounting hardware suitable for

use in a photovoltaic system.

| Always use the same type of module within a particular photovoltaic system.

| Under normal operating conditions, PV modules will produce currents and

voltages that are different than those listed in the date sheet. Data sheet

values are applicable at standard test data.

| Short-circuit current and open-circuit voltages should be multiplied by a factor

of 1.25 when determining component voltage ratings, conductor ampacity,

fuse sizes and size of controls connected to the module or system output.

Refer to Section 690-8 of the National Electrical Code (NEC) for an additional

multiplying factor of 125 percent (80 percent de-rating) which may be applicable.

General installation notes

| Drainage holes must not be covered with parts of the mounting system. The

junction box has a breather port which must be mounted facing downward and

cannot be exposed to the rain. The junction box should be on the higher side of

the module when it is mounted in order to orient the breather port correctly.

| Do not lift the module by grasping the module's junction box or electrical leads.

| Do not stand or step on module.

| Do not drop the module or allow objects to fall on the module.

| Do not place any heavy objects on the module.

| Inappropriate transport and installation may damage the module glass or frame.

Mechanical Installation

Selecting the location

| Select a suitable location for installation of the module.

| For optimum performance, the module must be facing true south in northern

latitudes and true north in southern latitudes.

| For detailed information on optimal module orientation, refer to standard solar

photovoltaic installation guides or a reputable solar installer or systems integrator.

| The module should not be shaded at any time of the day.

| Do not install the module near equipment or in locations where flammable gases

can be generated or collected.

Selecting the proper mounting structure and hardware

| Observe all instructions and safety precautions included with the mounting

system to be used with the module.

| Do not drill holes in the glass surface of the module. Doing so will void the warranty.

| Do not drill additional mounting holes in the module frame. Doing so will void the

warranty.

| Modules must be securely attached to the mounting structure using four

mounting points for normal installation. If heavy wind or snow loads are

anticipated, additional mounting points should also be used. Please see the

drawing below.

| Load calculations are the responsibility of the system designer or installer.

| The mounting structure and hardware must be made of durable, corrosion- and

UV-resistant material.

Mounting methods

1. Mounting With Bolts

| The module must be attached and supported by at least four bolts through

the indicated mounting holes.

| Most installations will use the four inner mounting holes on the module frame.

| Depending on the local wind and snow loads, additional mounting points may

be required.

Please carefully read the following installation and safety instructions.

Non-compliance with these instructions may void the module warranty.

Page 1/2

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Conergy Q 85MU Zonnepaneel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Conergy. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Conergy Q 85MU Zonnepaneel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Conergy Zonnepanelen
Meer handleidingen voor Zonnepanelen