Handleiding Currys Essentials C20CHW10 Kachel

Handleiding

GB-1 GB-2

UN PA CK IN G

Remove all packaging from the unit. Retain the packaging. If you

dispose of it please do so according to any local regulations.

The following items are included:

CO NT RO L PA NE L

PR OD UC T O VE RV IE W

It is normal for the heater to emit some smell and fumes when it is turned

on for the rst time or when turned on after not being used for a long

period of time. This smell will disappear when the heater has been turned

on for a short while.

• Before drilling holes ensure that you will not damage any pipes or

wiring hidden in the wall.

• Do not permanently x the heater to the wall. It is only designed to

hang from the 2 angle brackets that are attached to the wall.

Ensure you unplug your heater from the mains socket and wait for the

heater to cool down completely before cleaning.

GB-3

OV ER HE AT P ROT EC T IO N

The power to the heater will automatically cut off if the temperature of the

heater exceeds a certain limit. In the event of overheating, the heater will

stop operating. Switch the heater off and allow it to completely cool. The

heater will then resume operating as normal.

WA LL M OU NT IN G (OP TI ON AL )

The heater can also be installed on a wall using the supplied accessories.

The feet should not be attached to the heater.

1. Drill 2 holes in the wall. Insert the wall plugs. Make sure the mains cable

can still reach a mains socket.

2. Install 2 angle brackets to the wall using the 4 type B screws.

3. Attach the other 2 angle brackets to the bottom of the heater housing

using the 4 type A screws. These will act as spacers. Do NOT attach

these 2 angle brackets to the wall.

4. Lift up the heater and mount it on to the 2 angle brackets that are

attached to the wall.

AS SE MB LY

Before using the heater, the feet (supplied) must be tted to the unit.

Attach the feet to the base of the heater using the 4 type A screws provided

(2 for each foot), taking care to ensure that they are located correctly in the

bottom ends of the heaters side moldings.

OP ER AT IO N

1. Position the heater upright on the oor away from curtains, furniture or

wallcoverings before plugging your heater into the mains socket.

2. Press the Power Switches to the “750W” or “1250W” position. The heater

has 2 built-in heating elements. You can select one or both heating

elements simultaneously.

3. Turn the Thermostat Control to the desired position. It is recommended

to select the “MAX” position to get the heater to pre-heat. It will take

5-10 minutes for the heater to fully heat up.

4. When the room reaches the desired temperature, turn the Thermostat

Control slowly anti-clockwise until the indicator goes off with a “click”

sound. The heater will temporarily go off.

5. If the room temperature falls below the desired temperature, the heater

and indicator will turn on again until the room temperature reaches the

desired temperature.

CL EA NI NG

Your heater should be cleaned regularly to stop dirt and dust building up

which will affect its performance. Ensure the air inlet and the air outlet are

not blocked.

This can be done with a vacuum cleaner, using the brush attachment.

If items are missing or damaged, please contact Partmaster (UK only).

Tel: 0844 800 3456 for assistance.

The Main Unit Foot x 2

(P.N.: A007)

Angle Brackets x 4

(P.N.: A008)

The Instruction Manual

(P.N.: C20CHW10-002)

Screws B (30mm) x 4

(P.N.: A003)

Screws A (15mm) x 4

(P.N.: A002)

Wall Plugs x 4

(P.N.: A001)

CO NV EC TO R HE AT ER

INS TR UC TI ON M ANU AL

C20 CH W1 0

Thank You for purchasing your new Currys Essentials

Convector Heater.

We recommend that you spend some time reading this instruction

manual in order to fully understand all the operational features it offers.

Read all the safety instructions carefully before use and keep this

instruction manual for future reference.

Air Inlet

Control Panel

Handle

Air Outlet

MIN MAX

Power Switches (with Indicators)

750W = Approximately 750W heat output

1250W = Approximately 1250W heat output

750W+1250W = Approximately 2000W heat

output

Thermostat Control

Fit the screws in the

adjacent position

Screw A

at least 600mm

at least 400mm

CEILING

SIDE WALL

GROUND

at least 300mm

Bottom view

Screw B

Screw A

415mm

C

M

Y

CM

MY

CY

CMY

K

C20CHW10_IB_110615.pdf 2 15/06/2011 2:41 PM

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Currys Essentials C20CHW10 Kachel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Currys Essentials. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Currys Essentials C20CHW10 Kachel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Currys Essentials Kachels
Meer handleidingen voor Kachels

Beoordeling

Veelgestelde vragen over Currys Essentials C20CHW10 Kachel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Currys Essentials C20FHW18 Kachel

Handleiding

Currys Essentials C20FHW17 Kachel

Handleiding

Currys Essentials C20FHW20 Kachel

Handleiding

Currys Essentials C20CHW18 Kachel

Handleiding

Currys Essentials C7MOR10 Kachel

Handleiding

Currys Essentials C20CHW11 Kachel

Handleiding

Currys Essentials C7MOR12 Kachel

Handleiding

Currys Essentials C20FHW10 Kachel

Gerelateerde categorieën