Handleiding Dolmar PS-352 TLC-40 Kettingzaag

Handleiding

5

Operation

• When working with the chain saw always hold it with both hands. Take the

rear handle with the right hand and the front handle with the left hand. Hold the

handles tightly with your thumbs facing your ngers.

•

CAUTION: When releasing the throttle trigger the chain will keep on

running for a short period of time (free-wheeling).

• Continuously ensure that you have a safe footing.

• Hold the chain saw such that you will not breathe in the exhaust gas. Do not work

in closed rooms (danger of poisoning).

• Switch off the chain saw immediately if you observe any changes in its

operating behavior.

• The engine must be switched off before checking the chain tension,

tightening the chain, replacing it or clearing malfunctions.

• When the sawing device is hit by stones, nails or other hard objects, switch off

the engine immediately and check the sawing device.

• When stopping work or leaving the working place, switch off the chain saw and

put it down such that nobody is endangered.

•

CAUTION: Do not put the overheated power chain saw in dry grass or on

any inammable objects. The mufer is very hot (danger of re).

• CAUTION: Oil dropping from the chain or guide bar after having stopped the saw

chain will pollute the soil. Always use an appropriate base.

Kickback

• When working with the chain saw dangerous kickbacks may occur.

• Kickback occurs when the upper part of the end of the guide bar inadvertently

touches wood or other hard objects.

• This causes the saw to be thrown back toward the user with great force and out

of control. Risk of injury!

In order to prevent kickback, follow these rules:

- Only specially-trained persons should perform plunge cuts, i.e., piercing timber

or wood with the tip of the saw!

- Never apply the end of the bar when starting to make a cut.

- Always observe the end of the guide bar. Be careful when continuing an

already started cut.

- When starting to cut the chain must be running.

- Ensure that the chain is always sharpened correctly. Pay special attention to

the height of the depth limiter.

- Never cut several branches at the same time. When cutting a branch ensure

that no other branch is touched.

- When crosscutting a trunk be aware of the trunks next to it.

Working behavior/Method of working

• Only use the chain saw during good light and visibility periods. Be aware of

slippery or wet areas, and of ice and snow (risk of slipping). The risk of slipping is

extremely high when working on recently peeled wood (bark).

• Never work on unstable surfaces. Make sure that there are no obstacles in the

working area, risk of stumbling. Always ensure that you have a safe footing.

• Never saw above your shoulder height.

• Never saw while standing on a ladder.

• Never climb up into trees to perform sawing with the chain saw.

• Do not work leaning too far over.

• Guide the chain saw in such a way that no part of your body is within the

elongated swivelling range of the saw.

• Use the chain saw for sawing wood only.

• Avoid touching the ground with the chain saw while it is still running.

• Never use the chain saw for lifting up or removing pieces of wood or other

objects.

• Remove foreign objects such as sand, stones and nails found within the working

area. Foreign objects may damage the sawing device and can cause dangerous

kickback.

• When sawing precut timber use a safe support (sawing jack). Do not steady the

workpiece with your foot, and do not allow anyone else to hold or steady it.

• Secure round pieces against rotation.

• Maintenance

• Refuelling

• Sharpening the chain

• Stopping work

• Transport

• Putting out of function

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Dolmar PS-352 TLC-40 Kettingzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Dolmar. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Dolmar PS-352 TLC-40 Kettingzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Dolmar Kettingzagen
Meer handleidingen voor Kettingzagen

Veelgestelde vragen over Dolmar PS-352 TLC-40 Kettingzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Dolmar PS-6400 C Kettingzaag

Handleiding

Dolmar ES-34 TLC Kettingzaag

Handleiding

Dolmar ES2135A Kettingzaag

Handleiding

Dolmar 219 Kettingzaag

Handleiding

Dolmar 119 Kettingzaag

Handleiding

Dolmar PS3410-30 Kettingzaag

Handleiding

Dolmar PS4605-38 Kettingzaag

Handleiding

Dolmar 101 Kettingzaag

Gerelateerde categorieën