Handleiding E3 FX10 Fietscomputer

Handleiding

Battery Installation

To help you get started quickly, the computer and transmitter batteries have been installed at

the factory. Under normal usage the batteries should last approximately one year. The FX10

uses a 3V CR2032 button cell battery in the computer and an A23/LR23 12V battery in the

sensor/transmitter, both of which are available at most camera and electronic shops.

NOTE: Most problems that occur with cyclocomputers are caused by dead or weak batteries.

Should you need to replace the batteries, follow the steps below.

Computer Head

1. Remove the battery cap from the bottom of the computer using a small coin. See Figure 1.

2. Install the battery in the battery compartment with the positive (+) side facing the battery cap.

3. Reinstall the battery cap and tighten securely. NOTE: During a battery change, all data will be cleared from memory. Make

a note of your current wheel size settings and cumulative odometer mileage before replacing the battery so you can

reprogram these values once the new battery is installed (see “Program Wheel Size” and “Set the Odometer”).

4. If for some reason the screen is blank or shows an irregular display after a battery change, press the reset button on the

underside of the computer head. See Figure 8.

Sensor/Transmitter

1. Remove the battery cap from the top of the transmitter using a small coin. Remove the old battery and dispose of properly.

2. Install a new battery with the positive (+) end facing the cap. See Figure 2. Reinstall the battery cap and tighten  rmly, making sure that the

rubber O-ring does not get pinched or distorted, as this will compromise the unit’s watertight seal.

Determine Wheel Size

The FX10 uses wheel circumference (measured in millimeters) to calculate speed and distance. Before you can program the FX10 you must

calculate wheel circumference using one of the three methods below.

Tech Support 1(800)553-8324

0208_3

Made in China

FX10 Cycle Computer

c

25

c

25

Thank you for your purchase of an E3™ cycle computer. With all the features that a professional rider needs to keep track of a ride, the

FX10 is the perfect accessory for any cyclist. The added convenience of wireless transmission makes installation simple!

STEP 2

Attach the wheel magnet loosely to one of the spokes on the same side of the wheel as the sensor/transmitter.

Adjust the position of the magnet and sensor by sliding both pieces up or down to achieve 1-3mm of clearance

between the two (1mm is about the thickness of a penny). See Figure 7. If the magnet and sensor are not close

enough, the computer will not pick up a reading or readings will be inconsistent and erratic. Most problems that

occur when installing a new computer are related to magnet and sensor alignment and spacing.

STEP 3

Once the transmitter and wheel magnet are aligned properly, securely tighten both in place and trim the

excess zip-tie ends with scissors.

TEST OF INSTALLATION

Once installation is complete, test the unit to make sure everything is adjusted and working properly. Pick

up the front end of the bicycle and spin the front wheel. The computer should register a speed reading

within 1-2 seconds. If not, check the alignment of the wheel magnet and sensor, and make sure that the

space between the magnet and sensor is 3mm or less. Adjust as necessary and re-test.

NOTE: Wireless cyclocomputers are occasionally a ected by electromagnetic interference. Common

sources of electromagnetic signals include high voltage power lines, motor driven equipment and other

wireless devices (such as heart rate monitors). If you experience unusually high speed readings, check your

surroundings for possible sources of electromagnetic signals and move away from the source.

Select Wheel Size

When switching your computer between bikes with di erent wheel sizes, don’t forget to select the

appropriate wheel size setting (

1 or 2 ) for each bike. In the Average Speed display screen (AVG), press

and hold the RIGHT button for three seconds to change between wheel size

1 and wheel size 2 .

Using the Stopwatch

STEP 1

In the Stopwatch display screen (STP), press the LEFT button to start the Stopwatch. Press the LEFT button

again to stop the Stopwatch. While the Stopwatch is running, the computer will calculate an estimate of

Calories burned and Fat burned during the timed session.

STEP 2

When the Stopwatch is stopped, Stopwatch time, Calories burned (C) and Fat burned (Lb or Kg) will be displayed in a continuous loop.

Remember that Calories burned and Fat burned are only calculated while the Stopwatch is running.

STEP 3

To reset the Stopwatch, advance to the Stopwatch display screen (STP) and press and hold both the LEFT and RIGHT buttons for four seconds.

Reset Display Screens

The ATM, DST, AVS and MAX display screens are reset simultaneously. In the Automatic Ride Timer display screen (ATM), press and hold both the

LEFT and RIGHT buttons for four seconds to reset the data in all four screens.

The Stopwatch is reset independently. In the Stopwatch display screen (STP), press and hold both the LEFT and RIGHT buttons for four seconds

to reset the Stopwatch.

Maximum Speed can also be reset independently. In the Maximum Speed display screen (MAX), press and hold both the LEFT and RIGHT buttons

for four seconds to reset Maximum Speed.

To reset ALL display screens and ALL programmed settings (including Clock, Odometer, wheel size settings and weight), depress the reset button

on the underside of the computer head. See Figure 8.

1

8

Computer Functions

CURRENT SPEED (m/h or km/h)

Displays current speed, up to 105mph (168km/h). Accurate to 0.1m/h

or km/h. Always displayed at the top of the screen.

SPEED DISPLAY BAR

Provides a graphic display of current speed. Additional segments of bar

illuminate as current speed increases.

CLOCK (TIME)

Displays time of day in a 12 hour or 24 hour format.

AUTOMATIC RIDE TIMER (ATM)

Auto start/stop timer is activated by front wheel movement and

records actual ride time up to 9:59:59.

TRIP DISTANCE (DST)

Displays distance traveled during current ride (or since last reset),

up to 999.9 mi. or km.

ODOMETER (ODO)

Displays cumulative ride distance, up to 99,999 mi. or km.

SPEED COMPARISON (56)

Compares current speed to average speed. As you ride, a (5) or (6)

will appear next to current speed to indicate whether your current

speed is above (5) or below (6) your average speed. This function is

automatic, requires no programming and cannot be disabled.

AVERAGE SPEED (AVG)

Calculates average speed based on ride time (ATM) & trip distance (DST).

MAXIMUM SPEED (MAX)

Displays highest speed attained during a ride (or since last reset), up to

105m/h (168km/h).

STOPWATCH (STP)

Manual stopwatch allows you to time any portion of a ride, up to 9:59:59.

DUAL WHEEL SIZE SETTINGS

Wheel circumference is used to calculate speed and distance. The FX10

includes two wheel size settings (

1 and 2 ), allowing you to switch your

computer between two bikes with di erent wheel sizes (e.g. your road

bike and mountain bike).

AUTO SLEEP

To prolong battery life, the FX10 will automatically enter “sleep” mode

after 10 minutes of non-use. The computer will automatically restart as

soon as it receives input from the speed sensor, or when any button is

pressed.

SCAN MODE

Allows hands free viewing of all display screens. When scan mode is

activated, the computer will scroll through all display screens on a

continuous loop, displaying each screen for two seconds. To activate

scan mode, press and hold the LEFT button for three seconds in any

display screen. To exit scan mode, press the LEFT or RIGHT button in any

display screen.

+

2

6

1-3 mm

7

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je E3 FX10 Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met E3. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van E3 FX10 Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor E3 Fietscomputers
Meer handleidingen voor Fietscomputers

Veelgestelde vragen over E3 FX10 Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

E3 F8 Fietscomputer

Handleiding

E3 F11C Fietscomputer

Handleiding

Echowell Echo 3 Fietscomputer

Handleiding

Bikemate 22975 Fietscomputer

Handleiding

Echowell U5 Fietscomputer

Handleiding

Sunding SD-581A Fietscomputer

Handleiding

Bosch Kiox Fietscomputer

Handleiding

Mio Cyclo 500 Fietscomputer

Gerelateerde categorieën