Handleiding Filzer dZ2L Fietscomputer

Handleiding

COMPUTER DISPLAY

ODO

ODO

ODO

TM

TM

dZ2L Wired Cycle Computer

Owner's Manual

Problem

No Speedometer

reading

Slow display response

No Trip Distance

reading

Display shows

irregular figures

or blank screen

Solution

Temperature outside out

of operating limits

(32-125 ºF or 0-55 ºC)

Re-install computer battery

and verify that the

computer battery is good.

Improper magnet/transmitter

alignment. Check magnet/

tramitter alignment.

Improper magnet/transmitter

alignment. Check magnet/

tramitter alignment.

Trouble Shooting

Filzer

Made in China

Visit www.filzer.com for more great products.

Art No.: K-04-T-P3-GB-FILZER(dZ2L)

MOUNTING BRACKET INSTALLATION

Attach the mounting bracket to the right side of the handlebar

with the LARGE cable ties (Figure 3a and 3b). Make sure the

mounting bracket is clamped tightly and will not slip on the

handlebar. Slide the computer onto the mounting bracket until

it snaps firmly into position. Press the release button to

remove the computer (Figure 3c).

rubber

shim

Figure 3a

Figure 3b

Figure 3c

Press to

release

BATTERY INSTALLATION

Computer - (Note: Battery is pre-installed) Remove the

battery cover from the bottom of the computer using a small

coin. Install the 1.5V battery with positive (+) pole facing the

cover (Figure 1a). If the LCD shows irregular figures, take out

the battery and install again. This will clear and restart the

computer's microprocessor.

Fig. 1a

Computer battery

(1.5V/186/LR43/

L1142)

FUNCTIONS

mounting

bracket

magnet

computer battery

(1.5V/186/LR43/ L1142)

cable ties**

PARTS

WHEEL SIZE (WS): Before you

program your computer you need to

determine your Wheel Size (WS). WS

is the circumference of the front

wheel in mm. This value is entered

into the computer in order to calculate

speed and distance.

While charts provide a quick and easy

way to get WS, there are no standard

wheel sizes in the cycling world - i.e.

the circumference (or Wheel Size =

WS) of a 700x23 tire will differ from

one brand of tire to another - so for

accurate speed and distance values

on your computer you need to

measure your wheel circumference.

To obtain WS:

Method 1: Fast (and not so accurate)

method - use chart provided.

Method 2: Most accurate method:

a) See Figure 8.

b) Inflate your tires to their proper

pressure.

c) Put a mark on your front wheel on the outside

circumference.

d) Put a mark on the floor.

e) Put the mark on the wheel on the mark on the floor.

f) Rotate the wheel one full revolution until the mark on the

wheel is on the floor again. Mark this location.

g) Measure the distance between the marks on the floor in

mm. This is the Wheel Size (WS) (i.e. your wheel

circumference in mm).

h) Write this number down. The value should be between

1800 and 2200 mm for standard size tires. The unit can

accommodate WS values between 100 and 5999 mm.

Fig.8

WS=distance in mm

for one wheel revolution

WS

2

x

x

1

d

W h e e l D i a m e te r d WS

2 6 x 1 .0 1 9 1 3

2 6 x 1 .2 5 1 9 5 3

2 6 x 1 .4 2 0 0 5

2 6 x 1 .5 2 0 1 0

2 6 x 1 .7 5 2 0 2 3

2 6 x 1 .9 5 2 0 5 0

2 6 x 2 .0 2 0 5 5

2 6 x 2 .1 2 0 6 8

2 6 x 2 .3 2 1 7 0

7 0 0 x 1 8 2 0 7 0

7 0 0 x 2 0 2 0 8 6

7 0 0 x 2 3 2 0 9 6

7 0 0 x 2 5 2 1 0 5

7 0 0 x 2 8 2 1 3 6

7 0 0 x 3 0 2 1 7 0

2 7 x 1 " 2 1 4 5

2 7 x 1 1 /8 " 2 1 5 5

2 7 x 1 1 /4 " 2 1 6 1

HOW TO MEASURE WHEEL SIZE

SETUP/RESET: In SETUP mode you can set WHEEL SIZE

(WS), and KM/MILE. Press and hold the LEFT and RIGHT

buttons for 4 seconds to access initial setup mode. The digits

on the bottom row will flash - this is the WHEEL SIZE (WS)

setup. Note - all data will be lost.

WHEEL SIZE (WS): Press the RIGHT button to adjust the

value of the first digit of WS. Once you have entered the

correct value press the LEFT button to advance to the next

digit. Repeat for all four digits. Press the LEFT button to

confirm and advance to KM/MILE setup.

KM/MILE SELECTION (12/24): Km/Miles units for distance

and speed will flash. Press the RIGHT button to toggle

between kilometre (KM) and miles (M). Press the LEFT button

to confirm and exit setup.

ADJUSTING WHEEL SIZE (WS) and KM/M AFTER SETUP:

If you need to change WS or change KM/M after setup see

above SETUP/RESET section above.

SETUP

Congratulations on your purchase of the dZ2L cycle

computer by FILZER. This is an easy to use cycle

computer.

There are 3 main screens. Press the RIGHT button to toggle

between the three display screens.

Screen 1 displays Current Speed, Odometer (ODO), Speed

Comparator (+ or -) and Speed Tendency.

Screen 2 displays Current Speed, Tripometer (DST), Speed

Comparator (+ or -) and Speed Tendency.

Screen 3 displays Current Speed, Auto Trip Timer (TM),

Speed Comparator (+ or -) and Speed Tendency.

SPEEDOMETER

Instantaneous Speed is displayed on the

top row. The range of measurement is

from 0 to 99 KM/hr (0 to 99 M/hr) and

accuracy is + /-0.5 KM/hr (M/hr).

TRIPOMETER (DST)

Press the right button to scroll through

screens until DST is displayed on the left

side of the display. The trip distance

(DST) value is displayed on the bottom

row. Tripometer is activated automatically

with speedometer input. To reset DST to

zero go to the DST Screen and press and

hold the LEFT button for 2 seconds. Note:

Trip Timer (TM) will also be reset to zero.

TRIP TIMER (TM)

Press the right button to scroll through

screens until TM is displayed on the left

side of the display. The Trip Timer (TM)

value is displayed on the bottom row. Trip

Timer is activated automatically with

speedometer input (when the front wheel

is turning). It records only the time spent

actually riding. To reset TM to zero go to

the DST Screen and press and hold the

LEFT button for 2 seconds.

ODOMETER (ODO)

Press the right button to scroll through

screens until ODO is displayed on the left

side of the display. The total distance

traveled (ODO) value is displayed on the

bottom row. To reset ODO to zero, press

and hold LEFT and RIGHT buttons for 5

seconds or remove the battery. Note all

data will also be reset to zero and you will

enter setup mode.

SPEED COMPARATOR: A (+) or (-) sign appears on the top

right hand corner of the display. A (+) indicates you are

traveling faster than your average speed. A (-) indicates you

are riding slower than your average speed.

SPEED TENDENCY (Acceleration & Deceleration): A cyclist

icon appears on the top left hand side of the display. The

wheels turn forward to indicate acceleration, and turn

backwards to indicate deceleration.

AUTO START/STOP: To prolong battery life, the computer will

automatically switch off if the unit is left unused for more than 5

or 6 minutes. Display will reappear with a press on either

button or input from the front wheel.

COMPUTER FUNCTIONS

INTRODUCTION

Speedometer (0-99.9 Km/hr or M/hr)

Tripmeter (DST) (Up to 999.99 Km or M)

Odometer (ODO) (Up to 9999.99 Km or M)

Auto trip timer (TM) (59:59:59)

Speed Comparator (+ or -)

Speed Tendency

Figure 2c

Figure 2b

Figure 2d

Figure 2e

flat

spoke

normal

spoke

2mm max

computer

flat

spoke

round

spoke

Figure 2f

1

3

2

2

PARTS INSTALLATION LOCATION

Area - Mounting bracket (handlebar)

Area - Speed sensor (right fork)

Area - Speed Magnet (front wheel spoke)

Figure 2a

1

2

3

a) Install the mounting bracket as per page 5

b) See Figure 2a for routing of sensors wire.

c) Make sure that there is enough wire clearance so the

handlebars can rotate fully in both directions without pulling at

the sensor wire.

d) Without using LARGE cable ties - position the sensor on

the inside face of the right fork and the magnet on a wheel

spoke. Position the sensor and magnet in such a way so that

the magnet passes over the circle arrow on the sensor as

shown in Figures 2c, 2e and 2f.

e) Once you have determined the approximate position of the

sensor and magnet - loosely put the LARGE cable ties on the

sensor and attach the magnet to the correct spoke. See

Figures 2d and 2e on how to attach the spoke magnet. The

magnet should be maximum 2mm from the sensor.

f) Test out the positioning of the sensor and magnet by

rotating the front wheel to see if the computer registers a

speed value. If no value is registered reposition the sensor

and magnet again. Make sure the magnet passes over circle

arrow on the speed sensor as shown in Figure 2f. Once you

have positioned the magnet and sensor properly, tighten up

the sensor cable ties and ensure the magnet is securely

tightened.

g) Secure the rest of the wire securely to the frame of your

bicycle with the remaining SMALL cable ties. Make sure that

there are no dangling wires.

sensor

**LARGE cable ties

for computer mount

and sensor

**SMALL cable

ties for wire

**LARGE cable ties

for sensor

**SMALL cable

ties for wire

**LARGE cable ties

for computer mount

**LARGE cable ties

for computer mount

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Filzer dZ2L Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Filzer. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Filzer dZ2L Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Filzer Fietscomputers
Meer handleidingen voor Fietscomputers

Veelgestelde vragen over Filzer dZ2L Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.