Handleiding Fito ASD-5 Rookmelder

Handleiding

Instruction manual

OPTICAL SMOKE ALARM WITH 2 x 1,5V BATTERIES - 5 YEARS LIFETIME

Model: ASD-5

IMPORTANT INFORMATION

Correct usage will ensure you have valuable extra

time to escape. Every correctly installed smoke

detector will increase your potential escape time.

• A smoke alarm does not prevent fire.

• Install the smoke alarm in the correct place, if

possible in the middle of the ceiling.

• Keep the smoke detector out of the reach of

children.

• Test the unit on a monthly basis and after any

period of absence. When the alarm does not

sound, have your smoke alarm inspected by the

service point or when the smoke alarm is more

than 10 years old discard the alarm.

CAUTION: Never test with fire!

• Clean the smoke alarm regularly (once a month)

using the soft brush of a vacuum cleaner.

In addition the smoke alarm can also be cleaned

using a moist cloth.

• If the detector emits a beeping sound every 40

seconds, this means that the batteries are nearly

flat and that you should replace the smoke alarm.

• The lifespan of smoke detectors is 10 years.

• A false alarm can be silenced by pressing the test

and silence button.

• You can make your Model ASD-5 smoke detector

less sensitive for ± 10 minutes by pressing shortly

the test button. The detector will none-

theless sound the alarm if the quantity of smoke

is too significant.

Important instructions in case of a fire alarm:

• Plan TWO escape routes and rehearse these with

all members of the family.

• Agree upon a meeting point where everyone

gathers in the event of a fire.

In the event of a fire:

• Leave the building immediately together with all

the members of your family. Gather outside at the

agreed meeting point.

• Make sure everyone is present.

• Close all doors behind you and never open a

warm door. If a door is warm, choose an alterna-

tive route.

• In the event of considerable build-up of smoke,

crawl out of the building keeping as close to the

floor as possible.

• Wherever possible, breathe through a cloth (pre-

ferably moist), or else hold your breath as much

as you can. The majority of deaths and injuries

are caused by smoke inhalation rather than fire

itself.

• Call the fire department outside

• Never go back into a burning building.

• Additional information can be gathered at the

local fire department.

SPECIFICATIONS

Power:

2 x 1,5V LR03 AAA Alcaline

Recomended batteries: - PKCELL Ultra alcaline 1.5V

LR03. AAA.AM-4

- HUGE SUPER ALKALINE

1.5V AAA SIZE AM-4 LR03

- DURACELL Plus Power

Alkaline 1.5V LR03 MN2400

NOTE: The corect functioning of the smoke

detector is ensured by the use of one of the

recommended battery.

Battery life: 5 years under normal condi-

tions

Usage: < 8 µA continue

< 70 mA in alarm

Usage temperature: 0ºC tot + 55ºC

Humidity: 93% RH bij 40ºC

Sensitivity: Conform EN14604

Alarm volume: >85dB op 3 meter

&HUWL¿FDWLRQ $)125(1&( 

CPR

POSITIONING THE SMOKE DETECTOR

Recommended locations:

Minimum protection:

A smoke detector on each floor.

Maximum protection:

- Smoke detector in all rooms (with the exception

of bathrooms, kitchen, garages, etc.)

- Heat detectors can be installed in bathrooms,

kitchens, airing cupboards, utility rooms, etc.

within 5 metres of a potential source of fire.

• The smoke detector

should preferably

be installed in the

middle of the cei-

ling, at least 50 cm

from the wall.

• If ceiling mounting

is not possible to

mount the detector

on the wall. A

minimum of 30 and

maximum of 50 cm

from the ceiling.

(See Figure 3)

• In the case of

pitched roofs, install

the smoke detector

on the sloping wall,

at least 90 cm

(measured vertically)

from the ridge of the roof.

•

See minimum and

maximum protection

(figures 1 & 2)

• Ensure that the detector

can always be reached for

testing and cleaning.

Never fit a smoke detector:

• In bathrooms, kitchens, shower rooms, garages,

etc. Places where a smoke detector may go off

needlessly due to condensation, normal smoke or

gases. A smoke detector should be fitted at least 5

metres from such sources of smoke.

• Places where the temperature may exceed 55° C

or fall below 0° C, e.g. attics, just above a fire-

place, etc.

• In the vicinity of (or adjacent to) decorative objects,

doors, sockets, lights, fittings, windows, wall

ventilators, etc. which could mean that smoke

does not reach the smoke detector. Minimum

50cm away.

• Surfaces that are usually warmer or colder than

the rest of the room. Differences in temperature

can prevent smoke from reaching the detector.

• Adjacent to or directly above stoves or heaters.

• In very high or difficult to reach places. This makes

it hard to reach the detector to test or clean it.

0333-CPR-292126

EN14604:2005/AC 2008

DoP no: 0515

• In very dusty or dirty places. Accumulation of dust

will prevent smoke from reaching the smoke cham-

ber and in time will lead to a false alarm.

• Within 1 metre of dimmer switches and wiring.

Some dimmer switches can trigger a fault in the

detector.

• Within 1.5 metres of fluorescent lights. Electrical

impulses can adversely affect the functioning of

the detector.

• Outdoors and in spaces where a large number of

insects are found. Small insects in the unit’s detec-

tion chamber can disrupt the functioning of the

detector.

The labels on the rear side of the detector

contain important information.

INSTALLATION

1. Choose a location that satisfies the conditions as

described in: Positioning the smoke detector.

2. Remove the base plate of the detector by turning

the base plate anticlockwise (to the left).

3. Mark the mounting holes

in the base plate and

drill the holes (use a 6 mm

drill). If you do not use

the

dowls, then use a 3 mm

drill. Screw the base

plate securely onto the

ceiling. Make sure that

the base plate is tight

against the ceiling so

that no air circulation

above the smoke alarm

is possible, which could impede smoke detecti-

on.

If the opening is too large, this must be remedied

by the use of a filler.

4. Insert the supplied batteries in the correct man-

ner into the smoke alarm, pay attention to the +

and -. When activated, the alarm will sound a

tune.

5. Place the smoke detector on the base plate and

turn it until the smoke detector clicks into the

base plate. Turn the smoke detector clockwise

until you hear a click.

6. Make sure that the smoke detector is working

properly and that the battery has been activated

by pressing the test button. A beeping noise that

stops once the test button is released indicates

that the smoke detector has been activated and

is working properly.

ATTENTION: The smoke alarm should covered or

temporarily removed during renovation work or

structural alterations. Clean the smoke detector

with the soft brush from a vacuum cleaner once the

day’s work is complete, and then replace the

detector, always testing it by pressing the test

button once it has been reinstalled.

WARNING: covering the smoke alarm causes

loses its functionality.

The detector must never come into contact with

liquids.

CAUTION: Do not paint to the detector and do not

cover it.

FUNCTION TEST

Test your smoke alarm immediately after instal-

lation, monthly and after a period of absence.

• press the test button for at least 2-3 seconds

DORXGVLJQDOZLOOVRXQGDQGWKH/('ZLOOÀDVK

every 0,5 sec., this will stop once the test button

has been released.

REPLACING THE BATTERIES

• Remove the batteries from the smoke alarm

• Place the new batteries in the correct way into

the smoke alarm. Pay attention to

the + and the -

• Place the smoke alarm back on the base plate

and test the smoke alarm, see chapter Function

Test.

FUNCTION AND MEANING OF THE LIGHT

AND SOUND SIGNALS

Normal situation: The red LED light will flash once

every 320 seconds.

Alarm: Whenever the detector detects smoke, it will

emit a loud pulsing alarm and the red LED light will

flash continuously (

every 0,5 sec.) until the smoke

has cleared.

Low battery signal: A beeping signal every 40

seconds means that the batteries are nearly flat

and need to be replaced imediatly. This signal will

sound for 30 days.

See for the recomended batteries chapter

SPECIFICATIONS

Always do the function test when batteries are

replaced.

DUST WARNING:

3 short beep signals every 40 seconds means dust

in the smoke chamber. You have to clean the

smoke detector by using the soft brush from a

vacuum cleaner.

Test Button: Check that the smoke detector is

working and that the battery has been activated by

pressing the test button for at least 2-3 seconds.

The smoke detector will give alarm and stop when

you release the test button. Test the function of the

smoke detector once per months. When the alarm

does not sound, have your smoke alarm inspected

by the service point or when the smoke alarm is

more than 10 years old discard the alarm.

HUSH Button: Your detector is fitted with a pause

button (see figure 5). This is the same button as

the test button. Press the pause/test button shortly.

Your smoke detector will then go into a so-called

reduced sensitivity mode for + 10 minutes. The red

LED light will flash every 10 seconds to indicate

that the Hush button has been activated. The

detector will nonetheless sound the alarm if the

smoke is dense or increasing in quantity.

False Alarm: Press the test- hush button to stop

the alarm. (See Hush button)

CAUSES OF FALSE ALARM

The smoke detector can be activated by steam,

condensation, dust, smoke and small insects.

These are to be prevented as far as possible. See

section: Never fit a smoke detector. If a detector is

frequently giving a false alarm, it might be necessa-

ry to install the detector in another location.

Maintenance:

• Never allow the detector to come into contact with

fluids.

• Clean the detector regularly (once a month) using

the soft brush from a vacuum cleaner. In addition

the smoke alarm can also be cleaned using a

moist cloth.

• Repairs must be carried out by the manufacturer.

LIMITATIONS OF SMOKE DETECTORS

In countries where they are commonly in use,

smoke detectors have contributed to reducing

deaths and injuries. Independent bodies have esta-

blished that they were insufficient in around 35% of

fires, namely in the following situations:

• Where the battery had been removed or was not

working. For that reason, you should test the unit

regularly.

• Where smoke is not able to reach the detector in

the event of a fire, meaning the unit cannot be set

off. Examples include a fire on another floor

where there is no smoke detector, a fire behind

closed doors, a fire in a chimney or smoke being

blown away from the detector. For that reason,

smoke detectors are recommended in all rooms,

or at any rate on every floor.

• Where the alarm is not heard. A person may not

be woken by the alarm if that person had consu-

med excess alcohol and/or drugs.

• A few fires are not always detected on time, e.g.

smoking in bed, if there is no smoke detector in

the bedroom. In the case of escaping from gas or

violent explosions, improperly storing explosive

products and flammable liquids (petrol, paint,

methylated spirit, etc.), electrical faults, acids,

children playing with matches (fire).

• The lifespan of smoke detectors is 10 years.

PRODUCT WARRANTY

If used and maintained properly, the manufacturer

guarantees this product against material and/or

manufacturing faults for a period of 5 years from

the original date of purchase by the consumer.

Exceptions include damage arising from accidents

or misuse. If the product becomes defective within

the stated period, then it will be repaired or

replaced free of charge. Please do not attempt to

repair the product yourself or tinker with it, which

will invalidate the warranty.

DOP (Declaration of Performance)

The DoP can be downloaded on our website

www.fito.eu

INSTRUCTIONS FOR REMOVAL

Do not dispose of your old detector in

the bin, but rather hand it in to a local

collection point for small, electrical waste.

MADE IN EUROPE

Manufactured in Europ by: ARTON

6 Prutska str. - Chernivtsi 58008 - UKRAINE

European supplier:

Fito Products BV

Molenvliet 22

3961 MV

WIJK BIJ DUURSTEDE

Nederland

[email protected] - www.fito.eu

2017-10 vers. 1

16

RETAIN THESE INSTRUCTIONS FOR FUTURE USE!

These instructions for use contain important information for

correct installation and use of your smoke detector. Please

read this information carefully and retain these instructions for

future use.

ACTIVATION OF THE SMOKE ALARM:

Insert the supplied batteries in the correct manner into the

smoke alarm, pay attention to the + and -. When activated, the

alarm will sound a tune.

Make sure that the smoke detector is working and that the batte

-

ries have been activated by pressing the test button for a few

seconds. The smoke detector will give alarm and stop when you

release the test button.

&KDUDFWHULVWLFVFHUWL¿HGE\$)125

Ceiling and wall mount YES

Battery powered YES

Autonomy 5 years YES

Individual Alarm Indicator YES

Alarm silence facility YES

Suitable for installation in a

caravan

YES

Option to connect external

devices

NO

Interconnectable NO

Certified by : AFNOR Certification

11, rue Francis de Pressensé - F-93571 La Plaine - Saint Denis Cedex

www.afnor.org

kitchen

living room

bathroom

bedroom

hallway

Figure 1

bedroom

bedroom

bedroom

bedroomr bedroomhallway

kitchen

hallway

living

room

basement

Figure 2

Figure 3

Figure 4

Mounting holes :

screw: 3x25 mm

dowel : 5x30 mm

Figure 5

Test- and

hush button

LED light

0333

EN14604:2005/AC 2008

Essential characteristics: Performance:

Nominal activation conditions/sensitivity, response delay (res-

SRQVHWLPHDQGSHUIRUPDQFHXQGHU¿UHFRQGLWLRQV

Passed

Fito Products BV

Molenvliet 22

3961 MV Wijk bij Duurstede

The Netherlands

16

0333-CPR-292126

Operational reliability: Passed

Tolerance to supply voltage: Passed

Durability of operational reliability and response delay, tempera-

ture resistance:

Passed

Durability of operational reliability, vibration resistance: Passed

Optical smoke detector,

alerts you in the event

RI¿UHRUVPRNHDQGLV

suitable for residential

buildings.

Durability of operational reliability, humidity resistance: Passed

Durability of operational reliability, corrosion resistance: Passed

Durability of operational reliability, electrical stability: Passed

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Fito ASD-5 Rookmelder. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Fito. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Fito ASD-5 Rookmelder in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Fito Rookmelders
Meer handleidingen voor Rookmelders

Veelgestelde vragen over Fito ASD-5 Rookmelder

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Fito ASD-10 Rookmelder

Handleiding

Fito ASD-10QR Rookmelder

Handleiding

Fito ASD-10Q Rookmelder

Handleiding

Insafe Origin Rookmelder

Handleiding

Alecto SA-41 Rookmelder

Handleiding

FireHawk FHB10 Rookmelder

Handleiding

Smartwares RM174RF Rookmelder

Handleiding

FireX I240C Rookmelder

Gerelateerde categorieën