Handleiding Katana 220080 Cirkelzaag

Handleiding

CORDLESS CIRCULAR SAW INSTRUCTION MANUAL

2

The rating plate on your tool may show symbols. These represent important information about the product or

instructions on its use.

h) Never use damaged or incorrect blade washers or bolt. The

blade washers and bolt were specially designed for your saw,

for optimum performance and safety of operation.

Further safety instructions for all saws

Causes and operator prevention of kickback:

• Kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator;

• When the blade is pinched or bound tightly by the kerf closing

down, the blade stalls and the motor reaction drives the unit

rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the teeth

at the back edge of the blade can dig into the top surface of the

wood causing the blade to climb out of the kerf and jump back

toward the operator.

• Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below.

a) Maintain a rm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line with

the blade. Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the operator, if proper

precautions are taken.

b) When blade is binding, or when interrupting a cut for any

reason, release the trigger and hold the saw motionless

in the material until the blade comes to a complete stop.

Never attempt to remove the saw from the work or pull the saw

backward while the blade is in motion or kickback may occur.

Investigate and take corrective actions to eliminate the cause

of blade binding.

c) When restarting a saw in the workpiece, centre the saw

blade in the kerf and check that saw teeth are not engaged

into the material. If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is restarted.

d) Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under their

own weight. Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Blunt or improperly set

blades produce narrow kerf causing excessive friction, blade

SYMBOLS

Direct current, DC

Waste electrical products should not be

disposed of with household waste. Please

recycle where facilities exist. Check

with your Local Authority or retailer for

recycling advice.

Refer to instruction manual/booklet

Wear ear protection General warning

Wear eye protection Regulator compliance mark

Wear respiratory protection

220080

binding and kickback.

f) Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment

shifts while cutting, it may cause binding and kickback.

g) Use extra caution when making a “plunge cut” into

existing walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

h) Check lower guard for proper closing before each use. Do

not operate the saw if lower guard does not move freely

and close instantly. Never clamp or tie the lower guard into

the open position. If saw is accidentally dropped, lower guard

may be bent. Raise the lower guard with the retracting handle

and make sure it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

i) Check the operation of the lower guard spring. If the guard

and the spring are not operating properly, they must be

serviced before use. The lower guard may become sluggish

due to, gummy deposits, or a build-up of debris.

j) Lower guard may be retracted manually only for special

cuts such as “plunge cuts” and “compound cuts.” Raise

lower guard by retracting handle and as soon as blade

enters the material, the lower guard must be released. For

all other sawing, the lower guard should operate automatically.

k) Always observe that the lower guard is covering the

blade before placing saw down on bench or oor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

l) This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

m) Never hold piece being cut in your hands or across your

leg. Secure the workpiece to a stable platform. It is important

to support the work properly to minimize body exposure, blade

binding, or loss of control.

n) Do not use the tool with abrasive or masonry/wet diamond

wheels.

o) Only use blade diameter(s) in accordance with the

markings on

the tool.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Katana 220080 Cirkelzaag. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Katana. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Katana 220080 Cirkelzaag in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Katana Cirkelzagen
Meer handleidingen voor Cirkelzagen

Beoordeling

Veelgestelde vragen over Katana 220080 Cirkelzaag

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Skil 3571 DA Cirkelzaag

Handleiding

Metabo KT 18 LTX 66 BL Cirkelzaag

Handleiding

Meec Tools 017-408 Cirkelzaag

Handleiding

Worx WX531L Cirkelzaag

Handleiding

Skil 3575 DB Cirkelzaag

Handleiding

Fieldmann FDPP 200705-E Cirkelzaag

Handleiding

Clarke CCS185 Cirkelzaag

Handleiding

Parkside IAN 445969 Cirkelzaag

Gerelateerde categorieën