Handleiding NiteRider Pro 3600 Fietslamp

Handleiding

Pro 3600

Pro Series User Guide

1

2

3

1000

1800

3600

Run Times*Settings

6:00

3:30

1:30

Pro 3600

* Run times are approximations and will vary.

DOWNLOAD PROGRAMS FROM THE D.I.Y. SOFTWARE

To download Programs from the D.I.Y. Software, the Docking

Station must be powered by a wall outlet, the Docking Station must

be connected to the host computer and the headlamp must be

connected to the Docking Station.

1. Plug the AC Adapter into the Docking Station and then into

the wall socket. The “Power” indicator on the docking station

will illuminate solid red.

2. Plug one end of the USB Cable into the Docking Station and the

other end into the USB port of a computer. The “USB/PC”

indicator will illuminate solid yellow.

3. Connect the Pro 3600 headlamp to the Docking Station. The

“Headlamp” indicator will illuminate solid yellow.

4. Click the “Update” button on the D.I.Y. Software control panel

to initiate transmission of Programs to the headlamp. Refer to the

“D.I.Y. Pro LED Series Software Guide” for detailed information

on the software features and how they function.

5. Both the “USB/PC” and “Headlamp” indicators will blink

indicating Programs are being downloaded through the Docking

Station and into the headlamp.

6. With a successful download, the headlamp LED indicator

changes from red to green.

Warning: Disconnecting the headlamp from the docking station,

or the docking station from the computer, or disrupting power

to the docking station while transmitting Programs from the

D.I.Y. Software will create a problem. The headlamp will either

not operate or operate unpredictably. To correct this situation,

disconnect power to the docking station, wait 10 seconds, then

reconnect power. The D.I.Y. Software and docking station will

reconnect, then repeat the downloading process.

D.I.Y. SOFTWARE

The latest version of the D.I.Y Software is available to download at

www.niteriderservices.com. The software runs under Windows 2000

and above. For detailed information on the software please refer to

the “D.I.Y. Pro LED Series Software Guide”.

RIDING AT NIGHT

While a Pro 3600 lighting system will dramatically improve your

view, control and enjoyment of night riding, please remember that

cycling at night is an inherently dangerous activity. In addition to

using your lighting system properly and riding with extreme caution,

NiteRider urges you to:

• Never ride alone

• Always let someone know where you are going

• Wear a helmet and reective clothing

• Carry an auxiliary light and emergency supplies

• Make sure the headlamp, mounting bracket and battery

are securely fastened.

• Always disconnect the battery from the headlamp when

transporting the light system.

PROTECTING YOUR INVESTMENT

Properly charge your battery to maximize its lifespan (see the

“Battery Charging and Care” section for detailed information). When

not in use, always disconnect the headlamp from the battery tray.

To unplug, grasp the connector, not the cable.

The Pro 3600 will perform in wet weather conditions, but

submerging it in water will damage the system.

SUPPORT

If you experience diculties during product installation or operation,

NiteRider provides free telephone support on weekdays from 8:00

AM to 4:30 PM (Pacic Time) at 800.466.8366, extension 4. You

may also e-mail us at:

NiteRider Technical Lighting Systems, Inc.

8295 Aero Place, Suite 200

San Diego, Ca 92123

www.niterider.com

@

Support

niterider

dot

com

FACTORY SETTINGS

Factory settings are locked and cannot be changed. The Pro 3600

factory settings include 3 light levels and the one ash pattern. See

table below.

THERMAL STEP DOWN

If the Pro 3600 headlamp is used in a static air environment, such

as bench testing, heat retention, due to inadequate airow, may

cause the light output to “step down” to a lower level to avoid

damage. In rare cases of extreme heat retention the light will power

of to protect the LED’s from overheating. Use a fan if bench testing the

light in a static air environment.

DOCKING STATION

The Docking Station has two uses.

1. To recharge the Pro Series Li-Ion battery

2. To download Programs from the D.I.Y Software to the headlamp

BATTERY CHARGING AND CARE

Battery Recharging

A Pro 3600 (8-cell, 7.4v, 11.6Ah, Li-Ion) will fully charge in 5:00 hours

1. Plug the AC Adapter into the Docking Station and then into

the wall socket. The “Power” indicator on the docking station

will illuminate solid red.

2. Place the battery into the Docking Station. The “Battery”

indicator will illuminate solid blue indicating contact and that

the battery is ready to charge. A blinking yellow indicator

signies the battery is out of the permissible temperature

range for charging.

3. Status of the 5-step charging process is displayed on the front

panel of the Docking Station.

4. When the battery is fully charged the “Charged” indicator will

illuminate solid green and charging will shut o automatically.

5. Leaving the battery in the Docking Station indenitely will not

harm the battery. Every 24-hours the Docking Station will test

the battery level and apply a charge if required.

Warning: If the “Batt Error” indicator illuminates solid red contact

NiteRider Customer Service for assistance.

150-22843 - Rev A

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je NiteRider Pro 3600 Fietslamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met NiteRider. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van NiteRider Pro 3600 Fietslamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor NiteRider Fietslampen
Meer handleidingen voor Fietslampen