Handleiding Oregon RM313PNFA Wekker

Handleiding

FR

EN

Self-Setting Atomic Projection

Clock with Indoor Thermometer

RM313PNFA

User Manual

INTRODUCTION

Thank you for purchasing the Oregon Scientific™

Self-Setting Atomic Projection Clock with Indoor

Thermometer (model: RM313PNFA). This device

bundles precise time keeping, alarm and temperature

features into a single tool you can use from the

convenience of your home. Keep this manual handy as

you use your new product. It contains practical step-by-

step instructions, as well as technical specifications and

warnings you should know.

PACKAGE CONTENTS

Main unit

Power adapter

AA batteries for

main unit x 2

OVERVIEW

MAIN UNIT

2

1

3

4

5

6

7

8

9

10

1. / switch – Slide to toggle

continuous projection feature on/off.

2.

+ - Press to increase a value in setting mode, or

ip the projection by 180° in idle. Press and hold to

increase a value rapidly in setting mode, or to turn

on RF clock signal reception in idle.

3.

- - Press to decrease a value in setting mode, or

ip the projection by 180° in idle. Press and hold

to decrease a value rapidly in setting mode, or to

turn off RF clock signal reception in idle.

4.

- Press to display the alarm time and turn on/

off the alarm function. Press and hold to enter the

alarm setting mode.

5. - Press to toggle between clock:second /clock:

weekday display, or exit alarm time display. Press

and hold to enter setting mode.

6.

- Press to toggle between the US time zones.

7.

- Press to turn on the backlight and

projection for 5 seconds (see Projection/

Backlight section), or snooze the alarm. Press

and hold until the unit beeps to turn on the

projection for 5 minutes.

8. Projection lens

9. AC power adaptor jack

10. RESET – Press to reset the unit to default.

LCD DISPLAY

A

B

A. Time/Weekday/Seconds display

B. Calendar (Month/Date)/Alarm display, Indoor

temperature display

Symbol Description

RCC signal received

Alarm is on.

Low battery

Time zone selection indicator

Alarm display mode

GETTING STARTED

INSERT BATTERIES

1. Gently push the battery compartment cover in the

direction as arrow shown (see Overview section)

to remove it from the main unit.

2. Insert the batteries, matching the polarities (

+/-).

NOTE

Replace the batteries when displays, or

when the display is dim.

AC POWER

Plug the power cable to the power jack and plug the

power adapter into a suitable power outlet.

NOTE

It is recommended to insert the battery as a

backup power source.

CLOCK

CLOCK RECEPTION

This clock synchronizes automatically with a clock

signal. Press and hold + to turn on and search for

the clock signal.

The main unit receives WWVB signal as RCC signal.

Clock signal reception indicator:

Icons Description

Main unit is searching for clock

signal strength

(ash)

Main unit is searching for clock

signal

No clock signal

Strong RCC signal received

Weak RCC signal received

NOTE

It takes 2-10 minutes to receive the clock signal.

If the signal is weak, it could take up to 24 hours to

receive a valid signal.

SET THE CLOCK MANUALLY

1. Press and hold - to disable signal reception. The

icon turns off.

2. Press and hold

.

3. Press once or press and hold +/- to adjust the

setting for hour, minute, year, month, date,

temperature unit (°C/°F) and language.

4. Press

to conrm each setting.

NOTE

• The language options are English (

EN), Spanish

(SP), Italian (IT), French (FR) and German (GE).

• The RCC signal reception is on after each reset or

battery replacement.

• The RCC signal turns off automatically when you

set time, year, month or date manually.

• Press ZONE

to select required US time zone

(Pacic, Mountain, Central or Eastern) time as

shown on directly.

ALARM

SETTING/ADJUSTING ALARM TIME

1. Press and hold .

2. Press once or press and hold +/- to adjust the hour

and minute setting, then press to conrm.

To turn on/off the alarm, press .

OPERATION

When the alarm rings, the backlight will flash.

You may:

• Press

to stop. The alarm will ring again on the

next day.

• Press

to snooze. The alarm rings again

after 8 minutes.

PROJECTION/BACKLIGHT

Press to turn on projection and backlight for

5 seconds, or press and hold until the unit beeps to turn

on the projection for 5 minutes. For the optimal projection

results, place the unit within 1.5 - 2 m (5 – 6.5 ft) from

the ceiling or wall.

To use the continuous projection feature, connect the

AC power adaptor to a suitable outlet.

switches to

switches to

With

Adapter

Continuous

projection.

Press to

turn on the projection

and backlight for

5 seconds.

Press and hold

to turn on

the projection for

5 minutes.

Without

Adapter

Press to

turn on the

projection and

backlight for

5 seconds.

Press and hold

to turn on

the projection for

5 minutes.

No projection,

backlight turns on for

5 seconds.

NOTE

• When the unit connects to the power outlet, the

continuous projection turns on automatically. You

may turn on/off the continuous projection while the

unit is connected to the power outlet.

• When the projection is on for 5 minutes, press and

hold again to stop 5 minutes projection.

You hear a beep.

PRECAUTIONS

• Do not subject the unit to excessive force, shock,

dust, temperature or humidity.

• Do not immerse the unit in water. If you spill liquid

over it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or

corrosive materials.

• Do not tamper with the unit’s internal components.

This invalidates the warranty.

• Only use fresh batteries. Do not mix new and

old batteries.

• Images shown in this manual may differ from the

actual display.

• When disposing of this product, ensure it is

collected separately for special treatment.

• Placement of this product on certain types of

wood may result in damage to its finish for

which Oregon Scientific will not be responsible.

Consult the furniture manufacturer's care

instructions for information.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

• Do not dispose old batteries as unsorted municipal

waste. Collection of such waste separately for

special treatment is necessary.

• Please note that some units are equipped with

a battery safety strip. Remove the strip from the

battery compartment before rst use.

NOTE

The technical specifications for this product and

the contents of the user manual are subject to change

without notice.

NOTE

Features and accessories will not be available

in all countries. For more information, please contact

your local retailer.

SPECIFICATIONS

MAIN UNIT

L x W x H

115mm x 63mm x 105mm

(4.5in x 2.5in x 4.2in)

Weight 148 g

Temperature

range

-5°C to 50°C

(23°F to 122°F)

Temperature

accuracy

0°C to 40°C: ±1°C (± 2.0°F)

T<0°C : ±2°C (± 4.0°F)

T>40°C : ±2°C (± 4.0°F)

Resolution 0.1°C (0.2°F)

Power

2 x UM-4 (AA) 1.5 V batteries

3.6 V adapter

NOTE

When the indoor temperature is lower than

-5 °C (23.0 °F), the screen displays LL.L. When the

temperature is higher than 50 °C (122.0 °F), the screen

displays HH.H.

ABOUT OREGON SCIENTIFIC

Visit our website www.oregonscientific.com to learn

more about Oregon Scientific products.

For any enquiry, please contact our Customer Services

at [email protected].

Oregon Scientific Global Distribution Limited reserves

the right to interpret and construe any contents, terms

and provisions in this user manual and to amend it, at

its sole discretion, at any time without prior notice. To

the extent that there is any inconsistency between the

English version and any other language versions, the

English version shall prevail.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares that this Self-

Setting Atomic Projection Clock with Indoor

Thermometer (model: RM313PNFA) is in compliance

with the essential requirements and other relevant

provisions of Directive 1999/5/EC. A copy of the signed

and dated Declaration of Conformity is available on

request via our Oregon Scientific Customer Service.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

WARNING

Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE

This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this equipment

does cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try

to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

This Class B digital apparatus complies with Canadian

ICES- 3(B)/NMB-3(B).

DECLARATION OF CONFORMITY

The following information is not to be used as contact

for support or sales. Please call our customer service

number (listed on our website at www.oregonscientific.

com), or on the warranty card for this product) for all

inquiries instead.

We

Name: Oregon Scientific, Inc.

Address: 10778 SW Manhasset Dr.

Tualatin, Or 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: RM313PNFA

Product Name: Self-Setting Atomic Projection

Clock with Indoor Thermometer

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1, 41 Man Yue St.,

Hung Hom, Kowloon,

Hong Kong

COUNTRIES RTTE APPROVED COMPLIED

All EU countries, Switzerland CH

and Norway N

CONTENU DE L’EMBALLAGE

Unité principale

Adaptateur

secteur

2 piles AA pour

l’unité principale

VUE D’ENSEMBLE

UNITE PRINCIPALE

2

1

3

4

5

6

7

8

9

10

1. Interrupteur / – Faire

coulisser pour régler sur ON/OFF la projection

en continue.

2.

+ - Appuyez ici pour augmenter les réglages ou

inverser la projection de 180° en mode inactif.

Maintenez appuyé pour augmenter rapidement

les valeurs en mode réglage, ou pour activer le

signal de réception de l’horloge RF.

3.

- - Appuyez ici pour diminuer les réglages ou

inverser la projection de 180° en mode inactif.

Maintenez appuyé pour augmenter rapidement

les valeurs en mode réglage, ou pour activer le

signal de réception de l’horloge RF.

4.

- Appuyez ici pour afcher l’heure de l’alarme et

activer/désactiver l’alarme. Maintenez appuyé ce

bouton pour entrer dans les réglages de l’alarme.

5.

- Appuyez pour alterner entre l’affichage

des secondes et l’affichage des jours de la

semaine. Maintenez appuyé pour entrer dans

le mode de réglage.

6.

- Appuyez ici pour commuter entre les

différents fuseaux horaires US.

7.

(Mise en veille)- Appuyez pour mettre en

veille l’alarme ou activer le rétro-éclairage pendant

5 secondes (voir la section Projection/Retro-

éclairage). Maintenez appuyé jusqu’à ce que

vous entendiez un bip pour activer la projection

pendant 5 minutes.

8. Lentille de projection

9. Prise adaptateur AC

10.

RESET (Réinitialisation) – Appuyez ici pour

réinitialiser l’appareil.

AFFICHAGE LCD

A

B

A. Afchage de l’Heure/du Jour de la semaine/des

Secondes

B. Afchage du Calendrier (Mois/Date), de l’Alarme,

et de la température intérieure

Symbole Description

Signal RCC reçu

Alarme activée

Niveau de pile faible

Indicateur de sélection du fuseau

horaire

Mode d’afchage de l’alarme

POUR COMMENCER

INSTALLATION DES PILES

1. Poussez doucement le couvercle du compartiment

à piles dans la direction indiquée par la èche

(voir la section Vue d’ensemble) pour le retirer de

l’unité principale.

2. Installez les piles en respectant les indications de

polarité (+/-).

REMARQUE

Remplacez les piles lorsque l’icône

s’affiche ou lorsque la luminosité de l’affichage diminue.

ALIMENTATION SECTEUR

Branchez le câble de l’adaptateur secteur sur la prise

d’alimentation de l’appareil puis branchez l’adaptateur

sur une prise de courant.

REMARQUE

Il est recommandé d’installer les piles en

tant que source d’alimentation de secours.

HORLOGE

RECEPTION DE L’HORLOGE

L’ horloge est dés ignée pour se syn chronise r

au t om atiq u emen t av e c u n sig n al d’h o rlog e .

Maintenez appuyé + pour activer et rechercher le

signal d’horloge.

L’unité principale reçoit le signal DCF tant que

signal RCC.

Indicateur de réception du signal d’horloge:

Icônes Description

L’unité principale est à la re-

cherche d’un signal d’horloge

sufsamment puissant.

(ash)

L’unite principale est à la re-

cherche d’un signal d’horloge.

Pas de signal d’horloge

Signal RCC fort reçu

Signal RCC faible reçu

REMARQUE

Cela peut prendre entre 2 et 10 minutes

pour recevoir le signal d’horloge. Si le signal est faible,

cela pourra prendre jusqu’ à 24 heures pour recevoir

un signal valide.

SET THE CLOCK MANUALLY

1. Appuyez et maintenez appuyé pour désactiver le

signal de réception. L’icône s’éteint.

2. Appuyez sur et maintenez appuyé

.

3. Appuyez une fois sur, ou appuyez et maintenez

appuyé +/- pour ajuster le réglage de l’heure, des

minutes, de l’année, du mois, de la date, de l’unité

de température (°C/°F) et la langue.

4. Appuyez sur

pour conrmer chaque réglage.

REMARQUE

• Les opti

ons de langue sont l’anglais (EN),

l’espagnol (SP), l’italien (IT), le français (FR) et

l’allemand (GE).

• Le signal de réception RCC est activé après chaque

réinitialisation ou chaque changement de piles.

Réveil projecteur à réglage

automatique avec thermomètre

d’intérieur

RM313PNFA

Mode d’emploi

INTRODUCTION

Merci d’avoir choisi le Réveil projecteur à réglage

automatique avec thermomètre d’intérieur d’Oregon

Scientific™ (modèles: RM313PNFA). Cet appareil

regroupe une mesure du temps précise, une alarme,

et un suivi des températures dans un outil unique que

vous pouvez utiliser dans le confort de votre maison.

Conservez ce mode d’emploi à disposition lors des

premières utilisations de ce produit. Il contient des

instructions étape par étape, ainsi que des spécifications

techniques et autres avertissements que vous vous

devez de connaitre.

RM313PNFA_UM_MP_R9.indd 1 2015/8/27 11:04:05 AM

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Oregon RM313PNFA Wekker. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Oregon. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Oregon RM313PNFA Wekker in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Oregon Wekkers
Meer handleidingen voor Wekkers

Gerelateerde producten

Handleiding

Oregon RM336PES Wekker

Handleiding

Oregon DP200 Wekker

Handleiding

Oregon TW223 Wekker

Handleiding

Oregon DP100 Wekker

Handleiding

Oregon RMB899P Wekker

Handleiding

Oregon RM803 Wekker

Handleiding

Oregon CIR600 Wekker

Handleiding

Oregon RM330P Wekker

Gerelateerde categorieën