Handleiding Philips SQM7441 Muurbeugel

Handleiding

A

B

C

D

E

F

G

H

*

*

1

2 3

4

5

6

English

1 Important safety instructions

Caution

•

Read these instructions before you begin. If you are unsure

of any part of the process, contact a professional contractor

or installer for assistance. Improper installation can result in

injury or damage.

•The wall or mounting surface must be capable of supporting

the combined weight of the mount and the display; if not, the

structure must be reinforced.

•Locate pipes, wires, or any other hazards in the wall where

you wish to install the mount before drilling.

•Safety gear and proper tools must be used. Failure to do so

can result in injury or damage.

•Two people are recommended for installation. Do not

attempt to lift a heavy display without assistance.

•Follow all instructions and recommendations regarding

adequate ventilation and suitable locations for mounting

your display. Consult the owner‘s manual for your particular

display for more information.

•This wall mount is intended for use only with the maximum

weight of 25 kg (55 lbs). Use with heavier than the maximum

weights indicated may result in instability causing possible

injury.

2 Tilt wall mount (for LCD, Plasma, and LED

displays)

What's in the box

Wall plate (x1)

Mount arm (x2)

User manual (x1)

Hardware kit (x1)

Hardward kit

A

M8 x 63 screw (x2)

B

Lag bolt washer (x2)

C

Concrete anchor (x2)

D

M4 x 12 screw (x4)

E

M6 x 12 screw (x4)

F

M8 x 12 screw (x4)

G

M6 washer (x4)

H

M8 washer (x4)

Tools required

•

Phillips head screw driver

• Ratchet or driver with 13 mm (1/2”) socket

• Electric or portable drill

• 6 mm (1/4”) drill bit and stud nder for drywall

installation

• 10 mm (3/8”) Masonry bit for concrete installation

3 Installation

Mount to the drywall

Caution

For safety reasons, this mount must be secured to at least two

wood studs no less than 16” apart. The studs must be capable

of supporting the combined weight of the mount and display.

1 Use a high quality stud nder to locate two adjacent

studs where you wish to install your mount. Mark

both edges of each stud to help identify the exact

center.

Note

You must use the center of each stud to avoid cracking or

splitting the wood during installation.

2 Place the wall plate against the wall with the arrow

pointing up and level it using the integrated bubble

level.

3 While another person holds the wall plate in

position, mark two locations (one per stud) for

securing the mount to the wall (see Fig. 1).

4 Set the wall plate aside and drill a 6 mm (1/4”) pilot

hole at each marked location.

5 Place the wall plate back against the wall and attach

it using the lag bolts

A

and lag bolt washers

B

provided (see Fig. 2). Do not over-tighten these

bolts and do not release the wall plate until both

bolts are in place. Ensure that the wall plate remains

level after tightening the bolts.

Mount to the concrete wall

Caution

For safety reasons, the concrete wall must be capable of

supporting the combined weight of the mount and the display.

The manufacturer takes no responsibility for failure caused by

walls of insufcient strength.

1 Place the wall plate against the wall in the desired

location and level it using the integrated bubble level.

2 While another person holds the wall plate in place,

mark two locations on the wall for securing the

mount (see Fig. 3).

3 Set the wall plate aside and drill a 10 mm (3/8”) hole

at each marked location. Remove any excess dust

from the holes.

4 Insert a concrete anchor

C

into each hole so that

it is ush with the concrete surface (see Fig. 4). A

hammer can be used to lightly tap the anchors into

place if necessary.

Note

If the concrete wall is covered by a layer of plaster or drywall,

the concrete anchor must pass completely through the layer

to rest ush with the concrete surface.

5 Place the wall plate back against the wall and attach

it using the lag bolts

A

and lag bolt washers

B

provided (see Fig. 2). Do not over-tighten these

bolts and do not release the wall plate until all

bolts are in place. Ensure that the wall plate remains

level after tightening the bolts.

Attaching the mount arms to the display

Caution

Use extra care during this part of the installation. If possible,

avoid facing down your display as it may damage the viewing

surface.

Note

This mount comes with a selection of different screw

diameters and lengths to accommodate a wide variety of

display models. Not all of the hardware in the kit will be

used. If you cannot nd the appropriate screw size in the kit

provided, consult the manufacturer of your display for more

information.

1 Determine the correct diameter of screw to use

carefully by trying different size (M4, M6 and M8)

from the hardware kit (see Fig.5). Do not force

any of the screws – if you feel resistance, stop

immediately and try a smaller diameter screw.

2 Attach the mount arms to the back of your display

using the screws identied in steps 1. If you are using

M6 screws you will need to use M6 washers

G

. If

you are using M8 screws you will need to use M8

washers

H

Note

The mount arms must be attached with the tilt adjustment

screws facing towards the outer edges of the display (see Fig.

6). Otherwise, the tilt function cannot be accessed..

Final assembly

1 Loosen both tilt adjustment screws and set the tilt

to the desired angle. Make sure both arms are set

to the same angle before re-tightening both screws

securely.

2 With the help of another person, carefully lift your

display and place it on the wall plate. Gently apply

pressure to the bottom of your display so that the

clips on the mount arms lock to the wall plate. Do

not release the display until the mount arms have

securely hooked onto the wall plate.

Caution

Make sure that both arms are locked to the wall plate. For

safety reasons, this mount cannot be used unless both arms

are securely locked.

SQM7441

Register your product and get support at

www.philips.com/support

User manual

Manual del usuario

sqm7441_27_2L_um_150731.indd 1-3 31/07/2015 14:56:54

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Philips SQM7441 Muurbeugel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Philips. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Philips SQM7441 Muurbeugel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Philips Muurbeugels
Meer handleidingen voor Muurbeugels

Beoordeling

Veelgestelde vragen over Philips SQM7441 Muurbeugel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Philips SQM6415 Muurbeugel

Handleiding

Philips SQM6325 Muurbeugel

Handleiding

Philips SQM5322 Muurbeugel

Handleiding

Philips SQM3221 Muurbeugel

Handleiding

Philips SQM4122 Muurbeugel

Handleiding

Philips SQM5222 Muurbeugel

Handleiding

Philips SQM5312 Muurbeugel

Handleiding

Philips SQM7842 Muurbeugel

Gerelateerde categorieën