Handleiding RugGear RG730 Mobiele telefoon

Handleiding



User Manual

Receiver

Headphone jack

USB/Charging port

Distance and light sensor

Front camera

Touchscreen

Back button

Flashlight

Rear camera

Speaker

Lock screw

Secondary

microphone

Power key

Volume

up/down key

Home key

Main menu

Customizable key

(PTT – software

required)

Microphone

Overview

Installation of the micro-SIM

and micro-SD cards

Key

Command function

Power Key

Press and hold to power your phone on

and off.

From the standby mode, press and hold to

bring up the phone main menu.

From the standby mode, briey press this

key to turn off or wake the screen when the

phone is asleep.

Customizable

key

Press and hold to select a shortcut for an

app.

USB port

Data cable jack, OTG cable jack.

Secondary mic

Noise elimination.

Tip: key

combination

Take a screen shot: Press and hold the

volume down key and Power keys

simultaneously for 1 second.

The device is designed to t two standard micro SIM cards. Single SIM

card use supports connection to 4G networks.

If two micro-SIM cards are inserted, only one SIM card can be set as the

4G SIM. The other micro- SIM card slot only supports GSM networks.

Warning: Insert micro SIM cards only.

The use of other size SIM cards will void the product’s

warranty.

To install the memory card in your phone, please follow the steps

described below:

1. Start by powering off the phone.

2. To open the back compartment, unfasten the two screws at the

back by turning them counter-clockwise, as illustrated below.

3. Lift to remove the back cover from the phone, as illustrated in the

image below:

5. Pull the tray latches up to access the micro-SIM/SD card slots, as

illustrated in the image below:

6. Then place the micro-SIM and micro-SD card(s) inside the

corresponding slots, as shown:

7. Proceed to close (A) and then lock (B) each card holder, as indicated

by the arrows:

8. Replace the back cover by carefully pressing it down:

9. Finish by turning the screws clockwise to rmly tighten the back

compartment cover:

Note:

To avoid damage to your phone or loss of data, make sure that the

phone has been turned off, and there is no power or phone

connector plugged in before installing or removing the micro-SIM

card or micro-SD card.

After installation is complete, make sure the cover is rmly fastened.

Tighten the battery cover screws to avoid water damage or dirt from

entering the mobile phone.

It is recommended to use the supplied data cable and adapter, or a

RugGear approved data cable for the phone to charge.

The micro USB port is located on the

upper edge of the RG730, next to

the headset jack. Please refer to the

picture below:

Lift the rubber plug, before

inserting the headset or data

cable, as indicated below:

Tips: Insert / Remove the memory card:

In order to store additional multimedia les, you must insert a memory

card. The device accepts memory cards with a capacity of up to

64GB.Prior to uninstalling the memory card, ensure that all conditions

for a safe removal are met.

1. In standby mode, open the application list, and then select

Settings Storage Unmount SD OK.

2. Remove the memory card.

Charging the battery

Prior to using your phone for the rst time, let the battery drain

completely before charging it to full capacity.

It is recommended to use the supplied data cable and adapter, or a

RugGear approved data cable for the phone to charge. Unapproved

equipment or USB cables may cause damage to the device or cause

batteries to explode.

When the battery power level is low, the phone plays an alert and

displays a prompt, along with an empty battery icon

When the battery power is nearly depleted, your phone will power off

automatically. In this case, allow the battery to recharge in order to

continue using the phone.

If the battery is completely discharged, the device cannot be turned on

immediately even when connected to the charger. Allow the depleted

battery to charge for a few minutes before attempting to turn on the

device.

USB charger

Connecting the charger improperly may cause serious damage to the

device. Any damage caused by misuse is not covered by the warranty.

The device may heat up while charging. This is normal and should not

affect the lifespan or performance of the device. To save energy,

unplug the charger when not in use.

Wireless charging devices

The device's wireless charging function uses energy-saving and

comprehensive emission control technologies.

Before using the wireless charger function, closely follow all safety

precautions contained in this manual to ensure safe and proper use of

this product.

1. As this mobile phone features a built-in Qi wireless charging

receiver, it will only support chargers adhering to the Qi standard.

2. Do not expose the wireless charger to rain or water.

3. Do not disassemble, modify or repair the charger yourself.

4. Do not place the device inside or near heating equipment or high

pressure containers, such as water heaters, microwave ovens, or hot

cooking utensils.

Wireless charging diagram:

Extend battery life

Energy saving tips:

1. Turn off wireless communication when the Bluetooth, Wi-Fi or GPS

functions are not in use.

2. Decreasing the phone screen brightness and shortening of the sleep

timer delay setting will further reduce power consumption. You can

also press the power button to turn off the screen when not using

the device.

3. Disable the automatic synchronization of emails, calendars, contacts

and other applications

4. The installation and use of certain applications may decrease battery

life. Exit used applications by pressing the “recent apps” button to

view them and slide left/right to close.

Force system restart

Because this phone has a built-in battery, if the phone cannot be

turned off due to a screen freeze or fault, you can press and hold the

power key for 14 seconds to forcibly restart the device. As improper

use of this button may result in loss of some unsaved data, use this

method with great caution.

Gloves mode

The touchscreen can be operated with gloves on and with wet hands

too. In order to enable this function, go to Settings Display

Gloves mode selected. This increases the phone´s sensitivity to

respond more accurately when the glove ngers come in contact with

the touchscreen.

Water and dust resistance

Your device has been tested and shown to be water and dust resistant

in certain circumstances. Despite its compliance with these resistance

requirements, your device is not impervious to water damage in any

situation.

Caution: USB and headphone rubber plugs must be tightly closed,

and the rear battery cover perfectly tted and screwed, to ensure the

device will properly meet dust and water resistance standards.

This mobile phone underwent a drop test from a height of 1.2 meters.

To maintain the water and dust-resistant performance of the device,

please follow the recommendations listed below:

1. USB and headphone rubber plugs must be tightly closed, and the

rear battery compartment properly tted and screwed, to ensure

phone’s IP protection.

2. Avoid the continuous immersion of the phone in water because of

Its IP68 rating. However, the phone is able to withstand being

sprayed or exposed to water jets from any direction.

3. Do not expose your phone to water at high pressure, such as waves

or waterfalls.

4. Do not expose the equipment to salt, ionized or soapy water.

5. Do not use the phone in a spa or near a hot water source, since high

temperatures may degrade the waterproof rubber.

6. Do not open the battery compartment with wet hands. The internal

components must never come in contact with water.

7. Prevent your mobile phone from being intentionally soaked and do

not attempt to open the back cover in an extremely damp

environment, (such as a swimming or in the shower).

8. Never open the battery compartment if the unit is not thoroughly

dry.

9. Do not use any detergents or other chemical agents to clean the

device and the charger.

10. Rubber seals tted to the back cover are an important part of the

device. Take care when opening and closing the back cover to avoid

damaging them. Also, ensure that the rubber seals are free from

debris, such as sand or dust to prevent damage to the device.

11. The battery cover and the multifunction jack plug may be loosened

if the device is dropped or receives an impact. Ensure that all the

covers are properly aligned and tightly closed.

12. Under certain conditions, the phone is susceptible to slight

vibrations, such as when the volume level is set high. This is normal

due to its waterproof design and therefore does not affect the

performance of the device.

13. If you accidentally drop your phone in the mud, do not worry: just

ush it with clean water and dry it thoroughly before using it.

14. If you accidentally drop your phone on the beach; do not worry just

ush it with clean water and dry it thoroughly before using it.

15. If the device is immersed in water or the microphone or the speaker

gets wet, sound may not be heard clearly during a call. Wipe the

device with a dry cloth or dry it thoroughly before using it. The use of

a hair dryer is not allowed.

16. The touchscreen and other features may not work properly when

wet. It is recommended to continue using the phone only after it

has been completely dried.

Safety information

Read all the safety information before using your mobile phone to

ensure the safe and proper operation of the device:

• Use only RugGear-approved batteries, chargers, accessories, and

supplies.

• Do not place the device in extremely hot or cold places.

• Do not place the device inside or near heating equipment or high

pressure containers, such as water heaters, microwave ovens, or hot

cooking utensils.

• Do not touch the charger or the device with wet hands while the

phone is charging.

• Do not use your device outdoor during a thunderstorm.

• Turn the phone off in areas with a potentially explosive atmosphere,

such a gas station.

• When using the phone in a restricted area, observe all safety warnings

and regulations.

• Comply with all safety warnings and regulations regarding mobile

device usage while operating a vehicle.

• Do not use your device on airplanes.

• Do not use the phone in locations that are susceptible to radio

frequency interference, like hospitals, schools, etc.

• The use of your mobile phone near a pacemaker should be avoided as

it can interfere with the proper operation of the medical device. If you

must use the phone, maintain a distance of at least 6 inches (15cm) to

reduce interference, while holding the phone to the ear on the

opposite side of your body where the pacemaker is placed.

• If you use a hearing aid, contact the manufacturer for information

about radio interference and the device compatibility.

• If you use other medical devices, contact the manufacturer to

determine whether such equipment will be affected by the radio

frequency generated by this mobile phone.

• Never allow children or animals to bite, chew, or lick the phone or

battery.

• Do not touch the multifunction jack and the battery electrode with

either liquid or metallic conductive elements.

• Do not use the camera ash or light close to the eyes of people or

animals.

• To prevent possible hearing damage when using a headset, do not

listen to audio at high volume for prolonged periods of time.

• Do not attempt to disassemble, modify or repair the phone or its

accessories.

• Approaching other handset manufacturers for any changes or

modications will void the warranty. For service, contact the after-

sales service department of RugGear or your local dealer.

• Only qualied service personnel are allowed to repair the unit.

• The device can be used in locations with an ambient temperature of

-5°C to +45°C.

• The product includes a power adapter and a rechargeable battery,

with a charging voltage of 4.2V.

• The device can be charged in locations with an ambient temperature

of 0°C to +45°C.

Caution: there is a risk of explosion if the battery is replaced with the

improper type. Dispose of used batteries in accordance with applicable

guidelines.

Excessive sound pressure from earphones and headphones can cause

hearing loss.

Disclaimer

All content and services available through this device belong to third

parties and are protected by copyright, patent, trademark and other

intellectual property laws. Such content and services are intended

solely for personal, non-commercial use. You may not use any content

or services in the absence of a license from the content owner or

service provider.

In addition to the above limitations, unless expressly permitted by the

applicable content owner or service provider, you may not modify,

copy, republish, upload, post, transmit, translate, sell, create derivative

works, exploit, or distribute in any manner content or service otherwise

displayed through this device.

Third-party content and services are provided on an “as is” basis.

RugGear does not warrant contents or services so provided, either

expressly or impliedly for any purpose. Except as required by

applicable laws and regulations, RugGear disclaims any expressed or

implied warranties, including but not limited to, the implied warranties

of merchantability and tness for a particular purpose.

Third party services may be terminated or interrupted at any time, and

RugGear makes no representation or warranty that any content or

service will remain available for any period of time.

Content and services are transmitted by third parties by means of

networks and transmission facilities over which RugGear has no

control.

Without limiting the generality of this disclaimer, RugGear expressly

disclaims any responsibility for any interruption or suspension of any

content or service made available through this device.

RugGear is neither responsible nor liable for customer service related

to the content and services. Any question or request for service relating

to the content or services should be made directly to the respective

content and service providers.

Specific Absorption Rate (SAR)

The exposure standard for your wireless equipment employs a unit of

measurement known as the Specic Absorption Rate (SAR). The SAR

limit in Europe is 2.0 W/kg. The RG730 device has also been tested

against this SAR limit. The highest SAR value reported under this

standard during product certication for use at the ear is 0.2236W/kg

and when properly worn on the body is 0.761 W/kg. This device was

tested for typical body-worn operation with the back of the handset

kept 1.0cm from the body. To maintain compliance with RF exposure

requirements, use accessories that maintain a 2.5cm separation

distance between the user's body and the back of the handset. The use

of belt clips, holsters and similar accessories should not contain

metallic components in its assembly. The use of accessories that do

not satisfy these requirements may not comply with RF exposure

requirements, and should be avoided.

During use, the actual SAR values for this device are usually well below

81.00 mm

153.00 mm

the values stated above. This is because, for purposes of system

efficiency and to minimize interference on the network, the operating

power of your mobile device is automatically decreased when full

power is not needed.

Organizations such as the World Health Organization and the US Food

and Drug Administration have suggested that if people are concerned

and want to reduce their exposure, they could use a hands-free

accessory to keep the wireless device away from the head and body

during use, or they could reduce the amount of time spent using the

device.

This symbol on the device, battery and accessories

indicate that

they should be handed over to a collection point for

proper disposal at the end of their life.

NOTICE: This device complies with Part 15 of the FCC Rules [and with

Industry Canada license-exempt RSS standard(s)]. Operation is subject

to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Industry Canada Statement

Le present appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploitation est

autorisee aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'appareil doit accepter tout brouillage radioelectrique subi, meme

si le brouillage est susceptible d'en compromettre le

fonctionnement.

NOTICE:

Changes or modications made to this equipment not expressly

approved by RugGear may void the FCC authorization to operate this

equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses RF energy and can cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on. The user is encouraged to try to correct the

interference by one or more of the following measures:

o Reorient or relocate the receiving antenna.

o Increase the separation between the equipment and receiver.

o Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

o Consult the dealer or an experienced radio/TV technician for

help.

FCC/ISED RF exposure

information and statement:

The SAR limit of FCC (ISED) is 1.6 W/kg averaged over one gram of

tissue.

Device types: TD-LTE digital mobile phone (FCC ID: ZLE-RG730) has also

been tested against this SAR limit. The highest SAR value reported

under this standard during product certication for use at the ear is

0.2236W/kg and when properly worn on the body is 0.761W/kg. This

device was tested for typical body-worn operations with the back of

the handset kept 10mm from the body. To maintain compliance with

FCC RF exposure requirements, use accessories that maintain a 10mm

separation distance between the user's body and the back of the

handset. The use of belt clips, holsters and similar accessories should

not contain metallic components in its assembly. The use of

accessories that do not satisfy these requirements may not comply

with FCC RF exposure requirements, and should be avoided.

LTE-FDD Digital Mobile Phone

NFC antenna location

Wireless charging area

Camera

4. Micro-SIM and micro SD card compartments are in their locked

position. To unlock, gently slide the SIM/SD card holder upwards,

as illustrated in the image below:

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je RugGear RG730 Mobiele telefoon. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met RugGear. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van RugGear RG730 Mobiele telefoon in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor RugGear Mobiele telefoons
Meer handleidingen voor Mobiele telefoons

Veelgestelde vragen over RugGear RG730 Mobiele telefoon

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.