Handleiding Sierra Designs Hercules Assault V.2 Tent

Handleiding

S I E R R A D E S I G N S

SIERRA DESIGNS 2011 Cherry Street, Unit 202 Louisville, CO 80027 Phone: 303-262-3050 Fax: 303-262-3051 Toll Free: 800-635-0461

combination that runs along the B-C axis. After the pole frame is erected

attach the clips to the pole frame starting at the top of the tent. Do not

attach the Clip-Loc™ at this time. The lowest clips on the tent should

actually be clipped into the hub for added strength (Figure 5). Now take

the ridge pole of the two remaining poles (ridge pole is the longer of the

two) and feed through the two Clip Locs™ at points M and N and insert

the pole tips into the provided grommets at points O and P (Figure 3).

At this point you’ll need to engage the three Clip Locs™ by wrapping

the bungee cord tightly around the two poles and slide the cord into the

groove on the backside of the clip , to keep the cord taught (Figure 6).

With the vestibule pole place the tips of the poles into the grommets

attached to the swift clips at points 5 & 8 on the tent body (Figure 3).

Next attach the remaining clips to the vestibule pole, and stake out and

tighten the vestibule loops at points R & S (Figure 3).

Ventilation

Proper ventilation is essential for creating a comfortable living space in-

side your tent. The vestibule door panel can be rolled away for maximum

ventilation. Because the vestibule forms an awning over the door, you can

often leave the door tied open in a rainstorm, provided the door faces away

from the wind. In addition to the above the Hercules Assault v.2 has been

built with four vents, two in the back corners and two at the top of the

tent. By opening these vents and using the vestibule zippers at the top of

the vestibule you can regulate the ventilation.

Internal Guy System

Sierra Designs was the first to introduce the revolutionary Internal Guy

System. This system remains a very important feature in our Convertible

and 4-Season tents. When installed, this simple system will greatly in-

crease the strength of your tent with the weight of a few guy cords. This

system is very useful in extreme weather conditions, but is not necessary

under normal conditions. Installation: All attachments are made inside the

tent. All that is needed are 4 pieces of guy cord of 100” lengths or longer,

(line tighteners may be used but are optional). Some guy cords and line

tighteners are provided with your tent, however, you can also purchase

the “Internal Guy System” accessory, which uses Swift Clips to eliminate

the need to tie knots. There are nine webbing loops sewn to the interior

of the tent body: one in each corner of the floor at points A, B, C, & D

and four on the tent ceiling at points 5, 6, 7, & 8 (Figure 3). For added

strength along the sides of the tent, run the guy cords between points

on the tents as follows: A to 6, B to 5, C to 7, and D to 8. For added

strength along the front and rear of the tent, run the guy lines A to 8, b

to 7, C to 5, and D to 6 (in this configuration, the Internal Guy System

will partially obstruct the door way). With each guy cord, tie one end to

the webbing loop in the ceiling. Secure the other end to floor webbing

loop with a double half-hitch or a line tightener.

Please note that 6 tent stakes and 6 guy cords and line tighteners were

provided with this tent as a courtesy. If you choose to use more than this

when pitching your tent, additional stakes may be purchased at the store

where you originally purchased your tent.

First Pitch

In order to familiarize yourself with your new tent, we suggest that you

“test pitch” it before embarking on a wilderness trip.

Select a Site

Look for a level spot that is protected from the wind in order to ensure

sleeping comfort. Clear the area of debris such as sharp stones and sticks

which might abrade or puncture the tent floor. Choose an area that will

drain well when it rains.

Unfurl the Tent and Assemble the Poles

Unfurl the tent and lay the tent floor flat on the ground with the door

unzipped. There are four hub assemblies attached to the tent – one at

each corner of the tent. On each hub, assemble the short pole with their

corresponding hub insert (Figure 1). Lay these down at the corners of the

tent making sure that the webbing is not twisted. The hubs are attached

to the tent body by a side-release buckle, which makes untwisting and

storing easy. There are two poles of equal length as well as 2 shorter pre-

bent poles of shorter length. The pre-bent poles are used for the vestibule

(shorter) and the ridge pole (longer). Carefully unfold the shok corded

pole sections and allow them to slide together. Do not allow the poles to

snap together: this can lead to serious pole damage. Make certain that

the insert of each pole section and hub is fully inserted for correct set-up

(Figure 2).

Stake Out the Tent Floor

We recommend staking the floor prior to inserting the poles for greater

pitching ease. Although the Hercules Assault v.2 is a totally free stand-

ing tent, we suggest that you always stake the floor for greater stability,

especially in high winds. First, stake each of the webbing loops at points B

and D (Figure 3). Then move to the front of the tent, pulling the webbing

loops at points A and C until the tent floor is squarely and semi-tautly

positioned, and then stake them down.

Erect the Tent

Start with one of the main body poles and attach one of the open ends

to the insert on the hub attached to the stake loop at point A (Figure 4).

Take care that the webbing strap that attaches the hub to the stake loop

is not twisted. Then, still working with the same hub, insert the two

pole tips on the ends of the hub struts (short poles) into the grommets at

points E and F. Attach the other end of the pole into the hub attached

to the stake loop at point D, once again making sure that the webbing

is not twisted. Next insert the pole tips on the hub strut poles into the

grommets at points I and J. Repeat these steps for the other pole/hub

insert

incorrect

correct

HERCULES ASSAULT V.2

Your Sierra Designs

HERCULES ASSAULT V.2

tent is very easy to pitch

and maintain. Follow these

instructions to pitch your tent

quickly, safely and easily.

Figure 3: Tent Body (top view)

HERCULES ASSAULT V.2 TENT CONTENTS

Tent Body: 1 Line Tighteners: 6

Tent Poles: 4 Pitching Instructions: 1

Tent Stakes: 6* Stake Sack: 1

Guy Cords: 6 Pole Sack: 1

Hub Assembly: 4

* Sierra Designs tents include stakes for pitching the body under normal conditions.

Additional stakes may be required in severe conditions.

Figure 2: Correct Pole Assembly

Figure 6: Clip Loc

Figure 4: Insert Pole into Hub

Figure 1: Assembled Poles

vestibule pole

hub

TIGHTEN

FLOOR

TOWARD

CEILING

Figure 7: Line Tightener

Figure 5: Hub Assembly

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sierra Designs Hercules Assault V.2 Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sierra Designs. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sierra Designs Hercules Assault V.2 Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sierra Designs Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Sierra Designs Hercules Assault V.2 Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.