Handleiding Sierra Designs Reverse Combi Tent

Handleiding

S I E R R A D E S I G N S

SIERRA DESIGNS 2011 Cherry Street, Unit 202 Louisville, CO 80027 Phone: 303-262-3050 Fax: 303-262-3051 Toll Free: 800-635-0461

First Pitch

In order to familiarize yourself with your new tent, we

suggest that you “test pitch” it before embarking on a

wilderness trip.

Select a Site

Look for a level spot that is protected from the wind in

order to ensure sleeping comfort. Clear the area of debris

such as sharp stones and sticks which might abrade or punc-

ture the tent floor. Choose an area that will drain well when

it rains.

Unfurl the Tent and Assemble the Poles

Unfurl the tent and lay the tent floor flat on the ground

with the door unzipped. Carefully unfold the shock corded

pole sections and allow them to slide together. Do not allow

the poles to snap together: This can lead to serious pole

damage. Make certain that the insert of each pole section

is fully inserted into the next pole section (Figure 1).

You will have two poles of equal length. Each pole will

have 2 slightly pre-bent sections.

Stake out the Tent Floor

Although the Reverse Combi is a completely freestanding

tent, we suggest that you always stake out the floor for

greater safety and stability, especially in high winds. First

stake the webbing loops at corners A and B (Figure 2).

Then move to the opposite end of the tent, pulling the

webbing loops at corners C and D until the tent is square-

ly and tautly positioned, and stake down. Staking points E

and F is optional.

Erect the Tent

Insert the pole tips of one of the poles into the grommets at

points A and D, and the tips of the other into the grommets

at points B and C. Pull the two poles up so they intersect at

the center of the tent. Next, position yourself in the open

doorway and hook the Clip-Loc

™

(Figure 3) over the widest

angle of this intersection (do not attach the bungee cord yet).

Following the tent seams between points A and D, and B

and C attach all of the Swift Clips

™

to their corresponding

tent poles. Now attach the bungee cord on the Clip-Loc a

at the apex of the tent by wrapping the bungee in the di-

rection crossing the open gate of the

clip. Wrap the cord around the pole

intersection two to four times, de-

pending on desired firmness, then

slide the cord into the groove on the

backside of the clip to hold it taut

(Figure 3).

Fly Sheet

Making sure that the zippers are in front of the doors, drape

the fly over the tent. At the corners of the fly, points A, B,

C and D, are

3

/4" side-release “Fly Clip” buckles. Clip these

buckles (Figure 5) into their corresponding mates at points

A, B, C and D on the tent floor (Figure 2). By first clip-

ping the blue webbing strap on the rainfly to a blue

webbing strap on the body, you are guaranteed a fast, prop-

er rainfly set-up every time. Adjust the buckles to the

desired fit. Stake out the fly vestibule away from the tent

body at points H, I, J, & K. We recommend you stake out

points L & M for maximum ventilation. The tent may be

guyed out from points N, O, P, & Q for maximum stability

in high winds.

.

Ventilation

Besides staking and guying out all the points listed above,

optimal airflow through the tent itself can be obtained by

leaving part of the double-zippered vestibule open.

Vestibule

The vestibule can be pitched in a variety of configurations

to address different weather, storage, ventilation, or

wind conditions. The vestibule door may be folded in

half and attached to itself to form a half-door. The

entire door may be guyed out from points H, I, J, &

K to form a large awning, or it may be folded in half

to form a small awning. Or, the vestibule door may

be rolled entirely out of the way, forming an unob-

structed yet protected entrance

insert

incorrect

correct

A

B

C

D

L

M

H

I

J

K

NO

P

Q

6

A

F

E

B

C

D

REVERSE COMBI

Your Sierra Designs

REVERSE COMBI tent is very

easy to pitch and maintain.

Follow these instructions to

pitch your tent quickly,

safely and easily.

Figure 3: Clip-Loc

REVERSE COMBI TENT CONTENTS

Tent Body & Rainfly: 1 Portable Attic: 1

Tent Poles: 3 Footprint: 1

Tent Stakes: 8* Coffee Sling: 2

Guy Cords: 4 Pitching Instructions: 1

* Sierra Designs tent s include stakes for pitching the body and fly under normal conditions.

Additional stakes may be required in severe conditions.

Figure 4: Tent Fly (top view)

Figure 1: Correct Pole Assembly

Figure 5: Fly Clip

Figure 2: Tent Body (top view)

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sierra Designs Reverse Combi Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sierra Designs. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sierra Designs Reverse Combi Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sierra Designs Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Sierra Designs Reverse Combi Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.