Handleiding Smith Corona Memory Correct Typemachine

Handleiding

Margins

Margins are preset depending on your pitch

setting. They are:

10 Pitch 12 Pitch 15 Pitch

(Pica) (Elite) (Micro)

Left Margin 12 14 18

Right Margin 72 86 108

Changing Margins

When you need to change the margins,

follow the instructions below:

1. Press Back Space or Spacebar to

desired left margin.

2. Press Margin. Unit beeps.

3. Press Spacebar to desired right margin.

4. Press Code + Margin. Unit beeps.

Note: To signal that you are near the right

margin, your typewriter will beep once 5

spaces before the right margin.

Tabs

You can set up to six tabs, either regular or

decimal. Tabs may be set outside of

margins.

Regular Tab Decimal Tab

This is 123.56

a Regular 12.47

Tab 2.09

Regular Tabs

Regular tabs justify text at the tab stop. To

set a regular tab:

1. Position print hammer at desired location.

2. Press Tab S. Unit beeps.

Decimal Tabs

Decimal tabs are used to align numbers with

the decimal point. To set a decimal tab:

1. Position the print hammer at desired

location.

2. Press Code + D. Tab (O). Unit beeps.

3. Repeat steps 1 and 2 to set more decimal

tabs if desired.

4. Press Return when all tabs are set.

Using Tabs

Once tabs are set, they can be used as you

are typing your text.

1. Press Tab to move to tab location.

2. Type text. If using a decimal tab, type the

numbers preceding the decimal point. The

carrier moves to the left for each number

you type. If you make a mistake, press

Tab to start again.

3. Type the decimal point. The numbers

print to this point.

4. Type the numbers following the decimal

point.

Clearing a Tab

Both types of tabs are cleared the same way.

1. Position print hammer to tab setting.

2. Press Code + Tab (Tab C). Release

immediately. Unit beeps.

Clearing All Tabs Quickly

Press and hold Code + Tab (Tab C) until 2

beeps are heard. If you are positioned at a

tab stop, you will hear 3 beeps.

Pitch

Your typewriter has been designed with triple

pitch capabilities. To set the Pitch:

Press Code + Tab S for 10 Pitch.

Press Code + 1 for 12 Pitch.

Press Code + 2 for 15 Pitch.

Unit beeps when selecting pitch.

Note: Your typewriter is set at 10 pitch.

Change the printwheel if you select another

pitch. Changing pitch in the middle of a line

erases Correction Memory. However, after

the new pitch is selected, Correction Memory

begins again.

Line Spacing

Each time you turn the typewriter on, it is set

for single line spacing. You can change line

spacing to 1

1

⁄

2

line spacing or double line

spacing. To change line spacing:

Press Code + 3 for single line spacing.

Press Code + 4 for 1

1

⁄

2

line spacing.

Press Code + 5 for double line

spacing.

Unit beeps when selecting line spacing.

Impression Control

Impression control is the force used by the

print mechanism to strike the paper. When

you turn the typewriter on, it is set at

medium. You can change to light or heavy

impression. It is recommended that you

select heavy impression when typing on

carbons. For normal typing, use medium

impression. To set impression control:

Press Code + L for light impression.

Press Code + M for medium

impression.

Press Code + H for heavy impression.

The unit beeps when Impression control is

changed.

Note: Standard bond paper stock is

recommended for best quality. Copier paper,

erasable bonds and very heavily textured

bond papers do not print well with

Correctable Film ribbon. For these paper

types, we recommend High Density

Correctable Film or Multi-Strike ribbons. If

typing stencils, use those specifically

designed for daisywheel printers.

Correcting Text

There are two ways to correct typing errors:

off-line and on-line. The half-space feature

can be used for both.

On-Line Correction

The typewriter can automatically correct all

characters in a one-line memory buffer called

the Correction Memory. You can easily

correct characters no longer in Correction

Memory using Off-Line correction. After

correcting an error you can quickly return to

your previous typing position.

Important: Bold and auto underscore must

be activated before correcting characters

having these enhancements.

Correct Key

Use Correct for erasing character(s) in

Correction Memory.

1. Position the print hammer on the incorrect

character and then press Correct. Hold

down Correct to continue correcting, or

press Back Space and then Correct

again until all characters are removed.

2. Type correct text.

3. Press Code + Reloc (Return) if

necessary to relocate. The unit beeps.

Note: You erase Correction Memory when

you turn off the typewriter, press Return,

change pitch, or use the Half Space feature.

WordEraser



Key

Use WordEraser for erasing word(s) in

Correction Memory.

1. Position the print hammer on any

character in the right most word to be

corrected, and then press WordEraser

once for each word to be erased. If you

press WordEraser while between words,

the word to the left of the space will be

deleted.

2. Type correct text.

3. Press Code + Reloc (Return) if

necessary to relocate. The unit beeps.

Off-Line Correction

To correct an error not in the current line

Correction Memory:

1. Press Code + Up (6), Down (7), or

Return to position the print hammer on

the line containing the incorrect character.

2. Press Back Space or Spacebar to move

to incorrect character.

3. Press Code + Correct. The unit beeps.

4. With correction cassette installed, retype

the incorrect character to remove it.

5. Type the correct character.

Important: Bold and auto underscore must

be activated before correcting characters

having these enhancements.

Half Space

The Half Space feature is used when making

corrections when you omit a character or

type one too many. When the Half Space

feature is activated, the typing position

moves a half space to the right. Regular

spacing returns when the Half Space feature

is deactivated.

Note: When you activate the Half Space

feature, the Correction Memory is erased.

The typewriter remembers the half spaced

characters until the Half Space feature is

deactivated. Then, the typewriter begins to

remember normal spaced characters again.

Adding a Character

1. Press Correct or WordEraser to

erase error.

2. Press Back Space to position the carrier

one space before the first character of the

erased word.

3. Press Code + Half Space (Spacebar).

Print hammer advances a half space.

4. Type correct word.

5. Press Code + Half Space (Spacebar).

1

2

5

Important: Save all packing materials. If you

ship or move the typewriter, it should be

repacked in the original carton. See

“Shipping Instructions.”

This diagram depicts only basic features. For

information on coded features, see specific

chapters or the Quick Reference Guide at the

end of these instructions. Product

appearance and/or specifications are subject

to change without notice.

My Most Popular Features

Correcting Cassette

Easy to change and snap into place.

Automatic Memory Correction

Instant correction.

WordEraser

Erases an entire word.

Auto Center

Quickly and accurately centers text.

Bold

Highlights text.

Decimal Tab

Automatically aligns numbers by decimal

points.

Self Demonstration...

Activate this Self Demonstration Program

and discover my most popular features.

This built-in Demo is easy to use. Follow the

instructions below.

1. Insert Paper.

2. Press and hold Code while pressing Z.

3. Release both.

Hardware Basics

Typewriter Diagram

Inserting Paper

Note: Your typewriter handles 12” wide

paper and a 9” typing line. Standard bond

paper stock is recommended for best quality.

Copier paper, erasable bonds and very

heavily textured bond papers do not print

well with Correctable Film ribbon. For these

paper types, we recommend High Density

Correctable Film or Multi-Strike ribbons. If

typing stencils, use those specifically

designed for daisywheel printers.

1. Insert paper securely in the slot behind

the platen (3) against the paper alignment

mark. (For 12” wide paper, center on the

platen area.)

2. Advance

paper by using

the platen

knob (6), Index

Up/Down

feature, or

Return key.

3. Push the

paper release

lever (4) back,

and straighten

the paper if

necessary.

Return lever to

original

position.

4. Make sure the

protective

cover is in its

original

position.

Platen Knob/Variable Line Spacer

Rotate the platen knob to position the paper

up or down at variable line positions.

Removing Paper

To remove paper, push the paper release

lever back and gently pull the paper out of

the machine.

Turning the Typewriter Off

When typing is completed, move the power

switch to Standby. We suggest you unplug

the typewriter if it will not be used for an

extended period of time.

Keyboard

Code Key

The Code key is used in combination with

other keys to activate features. Code key

combinations are activated by pressing and

holding the Code key while pressing the

second key.

Shift Key

Press Shift while typing an alpha key to type

upper case letters or to type the characters

located on the top of certain keys, such as $, %.

Lock Key and

Indicator Light

Press Lock to type continuously in upper

case characters and access the characters

located on top of certain keys. The shift lock

light will light when Lock is pressed. To

deactivate shift lock, press Lock or a Shift

key. The light goes out.

Important: When the shift lock light flashes,

the typewriter has received an incorrect

command. Press Code to stop the flashing

light.

Repeat Action

All keys will automatically repeat when held

down except the following

Keyboard II characters: ^ ‘ ~ .

Format

Each time you turn on your typewriter, a

preset format is activated. It is set for general

typing purposes. These settings remain

active until you change them.

Setting Up

Before you can use your typewriter, you must

remove the packing materials from the print

mechanism. This is essential to the proper

functioning of your typewriter. Do not turn

the unit on until you have prepared the

typewriter for use. Follow the steps listed

below using the typewriter diagram for

reference. The numbers on the diagram

correspond to those in the instructions.

1. Tilt the protective cover (1) toward you.

2. Release the rubber band (left side first)

from the tabs.

3. Remove the print hammer restraint card.

4. Remove the ribbon cassette. If the

typewriter ribbon is slack, advance it by

turning the gear wheel on the bottom of

the cassette in the direction indicated (see

illustration).

5. Place the cassette back on the carrier,

and return the protective cover to its

original position. You will hear it snap into

place.

Turning the Typewriter On

The electrical cord is stored on the back of the

unit. Remove the plug from the protection slot

and unwind the cord for use.

1. Plug the typewriter into a proper electrical

outlet. (Use the correct electrical current.)

2. The symbol indicates the unit is in

Standby mode. This means your keyboard

is inactive until you select ON (|). Move

the power switch (5) to ON (| ). The carrier

(2) moves to the preset left margin.

Removing a Character

1. Press Correct or WordEraser to

erase error.

2. Press Code + Half Space (Spacebar).

Print hammer advances a half space.

3. Type the correct word.

4. Press Code + Half Space (Spacebar).

Note: Before activating the Half Space

feature on another line, you have to remove

the error using off-line correction procedures.

(See “Off-Line Correction.”)

Enhanced Text

You can enhance your text by using Bold,

Auto Center, Underscore, Superscript and

Subscript.

Bold Print

This feature is used for highlighting text. To

use Bold:

1. Press Code + Bold (B). Unit beeps.

2. Type text.

3. Press Code + Bold (B) to deactivate

bold.

Important: Bold and auto underscore must

be activated before correcting characters

having these enhancements.

Auto Underscore

You can automatically underscore just the

words or the words and spaces using the

Auto Underscore feature.

Activating Word Underscore

1. Press Code + Word (_/-). Unit beeps.

2. Type text.

3. Press Code + Word (_/-) to deactivate

Underscore.

Activating Underscore All

1. Press Code + All (+/=). Unit beeps.

2. Type text.

3. Press Code + All (+/=) to deactivate

Underscore.

Manual Underscore

You can manually go back and underscore

text.

1. Position print hammer under the first

character of the text to be underscored.

2. Press Shift + —.

Auto Center

This feature automatically centers text

between current margins. To use Auto Center:

1. Press Code + Center (0). Unit beeps.

The carrier moves to the center of the

margins.

2. Type the text. The carrier will backspace

in half space increments for each

character typed.

3. Press Return. Text prints and centers

automatically.

Note: If you make a mistake, press

Code + Center to restart centering. If you

decide not to center text, press Return prior

to entering text.

Superscript/Subscript

Your typewriter can easily create superscript

and subscript characters.

Typing Superscripts

1. Press Code + Super (9). Typing position

moves up

1

⁄

2

line.

2. Type the superscript. Carrier returns to

the original line.

Typing Subscripts

1. Press Code + Sub (8). Typing position

moves down

1

⁄

2

line.

2. Type the subscript. The carrier returns to

the original line.

Note: If you superscript or subscript more

than one character, you must repeat steps 1

and 2 above. If you decide not to type a

superscript or subscript after activating the

feature, press Correct to return to the

original line.

Correcting Superscript and

Subscript Errors

To correct errors made while using

Superscript or Subscript:

1. Press Back Space to error.

2. Activate superscript or subscript.

3. Press Code + Correct.

4. Type the incorrect character. It is erased

and carrier returns to original line.

This User’s Manual should be used with the following model: Memory Correct.

 Copyright Smith Corona Corporation, 1997.

799558 Rev. A NAES Printed in USA

Code

Lock

Shift

R

`

RRRRRR

4

3

6

MEMORY CORRECT

Electronic Typewriter

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Smith Corona Memory Correct Typemachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Smith Corona. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Smith Corona Memory Correct Typemachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Smith Corona Typemachines
Meer handleidingen voor Typemachines

Gerelateerde producten

Handleiding

Smith Corona Wordsmith 250 Typemachine

Handleiding

Smith Corona Wordsmith 150 Typemachine

Handleiding

Smith Corona Wordsmith 100 Typemachine

Handleiding

Smith Corona Spellmate Typemachine

Handleiding

Smith Corona Wordsmith 200 Typemachine

Handleiding

Panasonic KX-R194 Typemachine

Handleiding

Panasonic KX-R310 Typemachine

Handleiding

Underwood 3 Typemachine

Gerelateerde categorieën