Handleiding Sony M-670V Cassetterecorder
Handleiding voor je Sony M-670V Cassetterecorder nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.
Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.
Handleiding
Loading…
3-259-967-24 (1)
Operating Instructions
Mode d’emploi (voir verso)
M-673V/670V
Microcassette™-Corder
Recording
You can record right away with the built-in microphone.
Make sure that nothing is connected to the MIC jack.
* The button/jack has a tactile dot.
PAUSE
EAR
MIC (PLUG IN
POWER)*
Microphone
FF/CUE •
REW/REVIEW
Tape counter
reset button
VOL*
(Battery alert LED)
TAPE SPEED*
REC/BATT
VOR
Tape counter
1 Press the reset button of the tape counter.
2 Press and insert a standard microcassette with the side to
start recording facing the lid.
3 Select the desired tape speed.
2.4 cm for optimum sound (recommended for normal use): A 30-
minute recording can be made using both sides of the MC-30
microcassette (supplied for the United States and Europe only).
There is a tactile dot on this side.
1.2 cm for longer recording time: A 60-minute recording can be
made using both sides of the MC-30 microcassette (supplied for
the United States and Europe only).
4 Set VOR to OFF.
If you set VOR to ON, the unit automatically starts recording the
sound and pauses when there is no sound (you can save tapes and
batteries).
When the sound is not loud enough, set it to OFF, or the unit may
not start recording.
5 Press .
is pressed simultaneously and recording starts. While the tape
runs, the REC/BATT lamp lights and flashes depending on the
strength of the sound.
Recording level is fixed.
At the end of the tape, recording stops and the unit turns off
automatically (Automatic shut-off mechanism).
To Press or slide
Stop recording
Pause recording
Slide
PAUSE in the direction of the arrow.
To release pause recording, release
PAUSE*.
Start recording during
playback
during playback (the unit enters the recording
mode)
Review the portion just
recorded
Push up FF/CUE
•
REW/REVIEW toward
REW/REVIEW during the recording. Release the
button at the point to start playback.
Take out a cassette
*
PAUSE will also be automatically released when
is pressed (stop-
pause-release function).
Note
Select the 2.4 cm tape speed for recording, if you play back the recorded tape with
another unit. Otherwise, the sound quality may be changed.
Notes on VOR (Voice Operated Recording)
The VOR system is affected by the environmental recording conditions. When
you use the system in a noisy place, the unit will stay in the recording mode. If
the sound is too soft, on the contrary, the unit will not start recording. If you
cannot get the results you want, set it to OFF.
The VOR system may not record the beginning of the sound you want to record
because it starts recording only after it catches the sound. For an important
recording, set it to OFF.
To monitor the sound
Connect an earphone (not supplied) firmly to the EAR jack. The
monitor volume cannot be adjusted by VOL.
To prevent a cassette from being accidentally recorded over
Break off and remove the cassette tabs. To reuse the cassette for
recording, cover the tab hole with adhesive tape.
Recording from Various Sound Sources
Notes
When you are going to record something that you may not have an opportunity
to record again, test the unit first before you actually start recording.
When recording with an external microphone, the VOR system may not work
properly because of the difference in sensitivity.
Recording with an External Microphone
Connect a microphone firmly to the MIC jack.
M-673V : use the supplied microphone.
M-670V : use a microphone of low impedance (less than 3 kΩ).
When using a plug-in-power system microphone, the power to the
microphone is supplied from this unit.
Recording from another equipment
Connect another equipment firmly to the MIC jack using the
connecting cord (not supplied).
Set this unit to the recording mode and another equipment to the
playback mode.
Playing a Tape
VOL*
*
FAST PB
FF/CUE •
REW/REVIEW
EAR
* The button has a tactile dot.
TAPE SPEED*
PAUSE
(Battery
alert LED)
1 Insert a cassette with the side to start playing facing the lid.
2 Select the tape speed to the same speed as that used for recording.
3 Press .
4 Turn VOL to adjust the volume. There is a tactile dot beside VOL to
show the direction to turn up the volume.
At the end of the tape, playback stops and the unit turns off
automatically (Automatic shut-off mechanism). After the tape has been
wound or rewound, be sure to press .
If you plug in headphones (not supplied) to the EAR jack, you will get
monaural output from both left and right channels.
To Press or slide
Stop playback/stop fast
forward or rewind
Pause playback
Slide
PAUSE in the direction of the arrow. REC/
BATT lamp goes off.
To release pause playback, release
PAUSE*.
Fast forward** (FF)
Slide FF/CUE
•
REW/REVIEW toward FF/
CUE
during stop.
Rewind** (REW)
Slide FF/CUE
•
REW/REVIEW toward
REW/REVIEW during stop.
Search forward during
playback (CUE)
Keep FF/CUE
•
REW/REVIEW pushed
toward FF/CUE
during playback and release it at
the point you want.
Search backward during
playback (REVIEW)
Keep FF/CUE
•
REW/REVIEW pushed
toward
REW/REVIEW during playback and
release it at the point you want.
Start recording during
playback
*
PAUSE will also be automatically released when
is pressed (stop-
pause-release function).
** If you leave the unit after the tape has been wound or rewound, the batteries
will be consumed rapidly. Be sure to press
.
Note
If you leave the unit after the tape has been wound or rewound, the batteries will
be consumed rapidly. Be sure to press
•
REW/REVIEW switch may not
return to the center position when you release the switch. In this case, push back
the switch to the center to start playback.
To increase the playback speed
Slide the FAST PB
switch in the direction of the arrow. The
playback speed will be increased.
To return to the original speed, slide the FAST PB
switch to the
original position.
Precautions
On power
Operate the unit only on 3 V DC.
For AC operation, use the AC power adaptor recommended for the
unit. Do not use any other type. For battery operation, use two size
AAA (R03) batteries.
On the unit
Use only the (standard microcassettes) with this unit.
Non-standard cassettes cannot be used because their “L” dimension
(see illustration) is different.
Approx. 5 mm
Standard
Only standard microcassettes
have a small indention of side A.
Approx. 2.5 mm
Non-standard
Do not leave the unit in a location near heat sources, or in a place
subject to direct sunlight, excessive dust or mechanical shock.
Should any solid object or liquid fall into the unit, remove the
batteries or disconnect the AC power adaptor, and have the unit
checked by qualified personnel before operating it any further.
Keep personal credit cards using magnetic coding or spring-wound
watches etc. away from the unit to prevent possible damage from the
magnet used for the speaker.
When you do not use the unit for long, remove the batteries to avoid
damage caused by battery leakage and subsequent corrosion.
If the unit has not been used for long, set it in the playback mode and
warm it up for a few minutes before inserting a cassette.
If you have any questions or problems concerning your unit, please
consult your nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult
your nearest Sony dealer.
You cannot close the cassette compartment lid.
The cassette is being inserted in the wrong way.
has been already pressed.
The cassette is not being inserted completely.
The unit does not operate.
The batteries have been inserted with incorrect polarity.
The batteries are weak. Replace both batteries with new ones.
PAUSE is slid in the direction of the arrow.
The AC power adaptor is not firmly connected.
The unit will not run on dry batteries if the AC power adaptor is
left plugged into the DC IN 3V jack even though you disconnect
the AC power adaptor from the power source.
Recording cannot be made.
There is no cassette in the cassette compartment.
The tab on the tape has been removed. To reuse the tape for
recording, cover the tab hole with adhesive tape.
The batteries are weak. Replace both batteries with new ones.
Recording is interrupted.
The VOR switch is set to ON. When you do not use VOR, set it
to OFF.
Recording cannot be erased completely.
The head is contaminated. See “Maintenance”.
About This Manual
The instructions in this manual are for 2 models.
There is no difference among M-673V and M-670V except for the
supplied accessories.
M-673V consists of M-670V Microcassette recorder and the accessories.
For information about the supplied accessories, see “Specifications” of
this manual.
Preparing Power Sources
Choose one of the following power sources.
Dry Batteries
Insert the batteries
with correct polarity.
Make sure that nothing is connected to the DC IN 3V jack.
1 Open the battery compartment lid.
2 Insert two size AAA (R03) batteries with correct polarity and close
the lid.
To take out the batteries
To attach the battery compartment lid if it is accidentally
detached
When to replace the batteries
Replace the batteries with new ones of the same kind when the REC/
BATT lamp dims and the
lamp flashes.
Notes
The unit will play back normally for a while, even after the
lamp flashes.
However, replace the batteries as soon as you can. Otherwise, the built-in
speaker may emit a loud noise and recordings may not be made correctly.
In the following cases you do not need to replace the batteries:
– if the
lamp flashes with the playback sound when you turn up the volume.
– if the
lamp lights momentarily when the tape starts running or at the end
of the tape.
– if the
lamp flashes during FF/REW or CUE/REVIEW.
Battery life* (Approx. hours)
Batteries Recording Playback**
Sony alkaline LR03 (SG)*** 14.5 9
Sony manganese R03 (SB) 5 2.5
* Measured valued by the standard of JEITA (Japan Electronics and Information
Technology Industries Association) (Using a Sony Microcassette)
** Using a tape on which music has been recorded is played at volume setting 7
using speaker
*** When using Sony LR03 (SG) alkaline dry batteries (produced in Japan)
Note
The battery life may be shorter depending on the operating condition, the
surrounding temperature and battery type.
For maximum performance we recommend that you use
alkaline batteries.
House current
AC power adaptor
(not supplied)
to a wall outlet
Connect the AC power adaptor to DC IN 3V and to a wall outlet.
Use a commercially-available AC power adaptor (rated output voltage/
current: 3 V DC/700 mA).
Do not use any other AC power adaptor.
Polarity of the plug
Notes
Depending on the AC power adaptor, noise may be heard while using the unit.
Refer to the operating instructions of the AC power adaptor.
The voltage of power supply is different depending on the country. Please buy
an AC power adaptor in the country where the product is to be used.
Do not touch the AC power adaptor with wet hands.
Connect the AC power adaptor to an easily accessible AC outlet. Should you
notice an abnormality in the AC power adaptor, disconnect it from the AC
outlet immediately.
Playback cannot be made.
The tape has reached the end. Rewind the tape.
No sound comes from the speaker.
The earphone is plugged in. Unplug it.
The volume is turned down completely.
The sound drops out or comes with excessive noise.
The volume is turned down completely.
The batteries are weak. Replace both batteries with new ones.
The head is contaminated. See “Maintenance”.
Direct placement of the cassette tape on the speaker resulted in
magnetization and deteriorated tonal quality.
Use the unit away from radiowave-emitting devices such as
cellular phones.
Tape speed is too fast or too slow or the sound is distorted in the
playback mode.
Improper setting of the TAPE SPEED switch. Set it to the same
speed as that used for recording.
The FAST PB
switch is slid in the direction of the arrow.
The batteries are weak. Replace both batteries with new ones.
During CUE/REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
The batteries are weak. Replace both batteries with new ones.
Maintenance
Head
Pinch roller
Capstan
To clean the tape head and path
Press
and wipe the head, capstan and the pinch roller with a cotton
swab, moistened with alcohol every 10 hours of use.
To clean the exterior
Use a soft cloth slightly moistened in water. Do not use alcohol, benzine
or thinner.
Specifications
Tape
(normal position type)
Recording system
2-track 1-channel monaural
Speaker
Approx. 2.8 cm dia.
Tape speed
2.4 cm/s, 1.2 cm/s
Frequency range
300 Hz - 4 000 Hz (with TAPE SPEED switch at 2.4 cm/s)
Input
Microphone input jack (minijack/monaural/PLUG IN POWER)
sensitivity 0.2 mV for 3 kΩ or lower impedance microphone
Output
Earphone jack (minijack/monaural) for 8 Ω - 300 Ω earphone
Power output (at 10% harmonic distortion)
450 mW
Power requirements
3 V DC batteries size AAA (R03) × 2/External DC 3V power sources
Dimensions (w/h/d) (incl. projecting parts and controls)
Approx. 54.8 × 106.8 × 21.5 mm
Mass (main unit only)
Approx. 92 g
Supplied accessories
Microcassette tape MC-30 (1) (for the United States and Europe only)
Alkaline batteries LR03 (SG) (2) (M-673V, M-670V for the United States
only)
Microphone (1) (M-673V only)
Carrying pouch (1) (M-673V only)
Design and specifications are subject to change without notice.
©2004 Sony Corporation Printed in China
Loading…
Beoordeling
Laat ons weten wat je van de Sony M-670V Cassetterecorder vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.Meer over deze handleiding
We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sony M-670V Cassetterecorder. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sony. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sony M-670V Cassetterecorder in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.
Specificaties
| Merk | Sony |
| Model | M-670V |
| Categorie | Cassetterecorders |
| Bestandstype | |
| Bestandsgrootte | 0.95 MB |
Alle handleidingen voor Sony Cassetterecorders
Meer handleidingen voor Cassetterecorders
Praat mee over dit product
Laat hier weten wat jij vindt van de Sony M-670V Cassetterecorder. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.