Handleiding Sunding SD-201A Fietscomputer

Handleiding

BICYCLE COMPUTER

SUNDING（SD-201A）（21Functions）

FUNCTIONS

- SPD CURRENT SPEED

- ODO ODOMETER （0.001～99999km/m)

- DST TRIP DISTANCE

- MXS MAXIMUM SPEED

- AVS AVERAGE SPEED

- TM ELAPSED TIME .

- CLK CLOCK （12H/24H）

- PRM TEMPERATURE（-10℃~70℃）

- MIN PRM

- MAX PRM

- CAL（0～99999Kcal）

- FAT（0～9999.9kg）

- SCAN

- “+” “－” COMPARATOR

- SETTING SPEED SCALE（km/h,m/h）

- SETTING TYRE CIRCUMFERENCE :（0mm～9999mm）

- SETTING THE LAST VALUE OF ODOMETER/ODO

- FREEZE FRAME MEMORY

- SETTING THE RIDER’S WEIGHT

- MAINTENANCE ALERT

- AUTO ON/OFF

Computer Battery Installation

Remove the battery cover from the bottom of the computer by using a

flat blade screwdriver, install one CR2032 battery with the positive

(+)pole facing the battery cover and replace the cover. Should the LCD

show irregular figures, take out the battery and reinstall it.

Speedometer Sensor&magnet

Attach the speedometer sensor bracket to the left fork blade, using the

shims to adjust the diameter, and using the cable ties (as shown below)

to tie it with the fork. Position the sensor and magnet as show; make sure

that the arc of the magnet intersects the alignment mark on the sensor

with 1mm clearance.

Mounting Shoe

Attach the mounting shoe with the

cable ties to the handlebar, adjust the

mounting shoe on the handlebar with

the shims to hold its position. (three

type of mounting shoes for

choices )

Sensor Wiring

Route the sensor wire up the fork blade,

using cable ties to secure it at the bottom

and crown to avoid it hinder the movement

of the front wheel.

Computer

Attach the computer to the mounting shoe

by sliding the unit until it snaps firmly into

its postion. To remove it, press the button on

it in the opposite direction.

To check for proper speed function and

sensor alignment, spin the front wheel with

computer in speed mode. Adjust the position of sensor and magnet if

there is no or weak reaction.

Wheel Size Input

‘2060’ appears on the screen when the battery has been installed, with

one figure flashing, choose the correct wheel circumference from the

table below. Press RIGHT button to advance digits as needed and LEFT

button to confirm and advance.

(The circumference ranges 0mm～9999mm),press LEFT button to

enter KM/M mode

Setting KM/mile

Press the RIGHT button to choose km/h or

m/h. Press the LEFT button to enter into

ride’s weight setting.

Setting rider’s weight

The default weight is 65kg, press the RIGHT button to adjust the

flashing weight number according to rider’s weight, press LEFT button

to confirm and advance. Weight ranges : 20~150kg. Press the LEFT

button to enter into Maintenance Alert setting.

Setting maintenance alert

While the default Maintenance Alert digit

200km/m is flashing, Press the RIGHT button

to choose 200/400/600/800 km/m）

（Press the LEFT button to confirm and enter

into Clock mode.(When the ODO>the

Maintenance Alert digit you setted, the

will appear on the screen to alert the rider, press the LEFT button to

cancel it.)

CLK Mode(12H/24H)

In Clock mode, press the LEFT button

for 3 seconds to enter into 12h/24h

selection.Press the RIGHT button until Hour

digit flashes,thenpress the LEFT button to

adjust Hour .Press the RIGHT button

, until Minute digit flashes, then press the LEFT

button to adjust Minute .Press the RIGHT button twice to finish and

enter into ODO mode.

Setting the Last value of Odometer

In ODO mode, press the LEFT button for 2

seconds to set the ODO value, its initial

value is 0000.0. when one figure flashing,

press RIGHT button to adjust it and LEFT

button to confirm it, and start to set the next

figure.(after re-install the battery, latest

value can be inputted according to the value exists before the

battery is re-installed).

Reset of Mileage Parameter

In ODO mode, Press and hold both RIGHT and LEFT button

simultaneously for 3 seconds to clear the circumference value and cancel

(km/m) & Maintenance Alert setting. The user need to reset the tyre

circumference, (km/m) & Maintenance Alert, the original ODO value

and CLOCK will remain unaffected.

Speedometer

When riding speed is shown all the time on the screen, it ranges :0-

99.9km/h(m/h), and it is accurate to +/- 0.1km/h (m/h).

Speed Comparator

During riding , ▲and ▼will dispaly on the screen , ▲indicates the

current speed is higher than average speed. ▼indicates the current speed

is lower than average speed.

Odometer

In ODO mode , the total distance is indicated on

the screen, its mileage ranges : 0.001 ～

99999km(m). The display will be back to 0

when value exceeds its maximum limit, press

the RIGHT button to enter DST mode.

Trip Distance (DST)

In DST mode, the distance for one trip is

indicated on the screen. This distance is start to

be calculated when DST becleared to 0. It

ranges: 0~9999km(m), when exceed the range

limit, it will restart from 0 automatically. In

DST mode, press LEFT button for 5 seconds to clear the DST, MXS,

AVS, TM records. Press the RIGHT button to enter into MXS mode.

Maximum Speed (MXS)

In MXS mode, maximum speed is indicated on

the bottom line. Press the LEFT button for 5

seconds to clear the records of MXS,DST,AVS

and TM. Press the RIGHT button to enter AVS

mode.

Average Speed

In AVS mode, the average speed for one

trip is indicated on the screen. Press the

LEFT button for 5 seconds to clear the

AVS, DST, MXS, TM records. Press the

RIGHT button to enter Into TM mode.

Trip Time

In TM mode, the trip time for one trip is

indicated on the screen. TM ranges :

0 :00 :00~9 :59 :59,restartfrom0 :00 :00 when it

exceed the range limit. In TM mode, press the

LEFT button for 5 seconds to clear the TM, DST,

MXS, AVS records. Press the RIGHT button to enter into RPM mode.

Temperature (PRM)

In RPM mode, the current outdoor

temperature is indicated on the screen.

Minimum Temperature(MIN RPM)

Maximum Temperature(MAX RPM)

The default display for RPM is℃, press the

LEFT butoon for 3seconds, ℃ is flahing, press the RIGHT button to

exchange ℉/℃,press the LEFT button to confirm. RPM ranges :

-10~70 (℃), it is accurate to +/-0.1℃. In RPM mode, press the LEFT

button for 5 seconds to clear RPM MIN MAX, DST, MXS, AVS. Press

the RIGHT button to enter into CAL mode.

CAL (Calory)

In CAL mode, the total heat energy the rider consumed is calculated

from the last restoration of the computer is indicated on the screen. It

ranges: 0~99999Kcal. Press the RIGHT buttonto enter into FAT mode.

FAT

In FAT mode, the total FAT the rider

consumed is calculated from the last restoration of

the computer is indicated on the screen. It ranges:

0~9999.9kg. Press the RIGHT button to enter into

Scan mode.

SCAN

In SCAN mode, the DST, MXS, AVS, TM are

indicated in turn every 4 seconds. Press the

RIGHT button to enter into CLK mode.

Menu Hide Function

In any mode except CLK mode, press the RIGHT button for

5 seconds, the computer is going to Menu hide mode, it

hides MIN RPM, MAX RPM, CAL & FAT, which will not

be indicated on the screen but still running without effect.

Also in any mode except CLK mode, press the RIGHT

button for 5 seconds again, these functions are resumed.

Sleep Mode

If no signal has been inputted for 300 seconds, computer

will enter into Sleep mode, CLK remains. It will turn back to

the former mode with all the data collected when any signal

is inputted or any button is pressed.

FREEZE FRAME MEMORY

In any mode, press the LEFT button to enter into Freeze

Frame memory mode, flashing TM data will appear on the

screen, press the RIGHT button to view the records of DST,

TM, AVS and MXS. Press the LEFT button to end it.

Malfunctions and Problems

Malfunctions

Problems

No speedometer

Improper magnet/sensor alignment

Inaccurate value is

indicated

Improper input, such as wheel

circumference.

Slow display

response

Temperature exceeds operating

limits(0℃～55℃).

Black display

Temperature too high, or put in direct

sunlight for too long time. Need back to

shadow place for a period.

Weak display

Poor battery contact or dead battery.

Display shows

Irregular figures

Take out battery and reinstall it after 10

seconds.

Accessories

TIRE SIZE

CIRC

TIRE SIZE

CIRC

700c x 38mm

2180

26’’ x 2.25’’

2115

700c x 35mm

2168

26’’ x 2.1’’

2095

700c x 32mm

2155

26’’ x 2.0’’

2074

700c x 30mm

2145

26’’ x 1.9’’/1.95’’

2055

700c x 28mm

2136

26’’ x 1.75’’

2035

700c x 25mm

2124

26’’ x 1.5’’

1985

700c x 23mm

2105

26’’ x 1.25’’

1953

700c x 20mm

2074

26’’ x 1.0’’

1913

700cTubulari

2130

24’’ x 1.9’’/1.95’’

1916

650c x 23mm

1990

20’’ x 1-1/4’’

1618

650c x 20mm

1945

16’’ x 2.0’’

1253

27’’ x 1-1/4’’

2161

16’’ x 1.95’’

1257

27’’ x 1-1/8’’

2155

16’’ x 1.5’’

1206

26’’ x 2.3’’

2135

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Sunding SD-201A Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Sunding. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Sunding SD-201A Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Sunding Fietscomputers
Meer handleidingen voor Fietscomputers

Veelgestelde vragen over Sunding SD-201A Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Sunding SD-563C Fietscomputer

Handleiding

Sunding SD-576B Fietscomputer

Handleiding

Sunding SD-548B Fietscomputer

Handleiding

Sunding SD-568 Fietscomputer

Handleiding

Sunding SD-201C Fietscomputer

Handleiding

Sunding SD-548C Fietscomputer

Handleiding

Sunding SD-577C Fietscomputer

Handleiding

Sunding SD-548A Fietscomputer

Gerelateerde categorieën