Handleiding Traulsen TBC5 Blast chiller

Handleiding

IV. d - INSTALLING LEGS OR CASTERS (cont’d):

To install the legs or casters, rst raise and block the unit a

minimum of 7” from the oor.

For model TBC5 slide the legs or casters into the two chan-

nels under the front and back of the cabinet (see gure 1).

Secure in place by tightening the two bolts located at the

base of each leg or caster. NOTE: Legs or casters must

be installed towards the four corners of the unit for proper

support.

On model TBC13 thread the legs into the threaded holes

on the bottom of the cabinet (see g. 2). Be certain that all

legs are tightened securely. When the unit is set in its nal

position, it is important for proper operation that the unit be

level. The legs are adjustable for this purpose, turn the bot-

tom of the leg counter-clockwise to raise it, clockwise to lower

it. Level the unit from front to back as well as side to side in

this manner, using a level placed in the bottom of the cabinet.

For installing optional casters, these are “plate” type, and

require the use of four (4) bolts to secure them rmly to the

cabinet bottom at each corner (see gure 3). The caster

bolts are tightened using a 1/2” socket wrench.

IV. e - INTERIOR ARRANGEMENTS:

Models TBC5 and TBC13 are shipped with their full compli-

ment of tray slides already installed from the factory. Upon

delivery the plastic ties used to secure these during shipping

should be removed prior to rst use.

The slides are spaced to allow for maximum capacity of 2”

deep pans. If use of deeper pans is required, the slides can

be removed and adjusted to accommodate this. However

please note that the total quantity of pans possible will be

reduced in order to make room for the deeper pans.

Model TBC1H and TBC1HR are designed to accommodate

one roll-in rack with overall dimension (wheels inboard of

frame) which do not exceed 72” high by 27” wide by 29” deep.

Fig. 1

-3-

III. RECEIPT INSPECTION

All Traulsen products are factory tested for performance and

are free from defects when shipped. The utmost care has

been taken in crating this product to protect against damage

in transit. All interior ttings have been carefully secured and

the legs or casters are boxed and strapped inside to prevent

damage. Door keys will be attached to the handle with a

nylon strip. The handle is protected by an easily removable

nylon netting.

You should carefully inspect your Traulsen unit for damage

during delivery. If damage is detected, you should save all the

crating materials and make note on the carrier’s Bill Of Lading

describing this. A freight claim should be led immediately.

If damage is subsequently noted during or immediately after

installation, contact the respective carrier and le a freight

claim. Under no condition may a damaged unit be returned

to Traulsen without rst obtaining written permission (return

authorization).

IV. a - LOCATION:

Select a proper location for your Traulsen unit, away from

extreme heat or cold. Allow enough clearance between

the unit and the side wall so that the door(s) may open a

minimum of 90°.

IV. b - PACKAGING:

All Traulsen units are shipped from the factory bolted to a

sturdy wooden pallet and durably packaged. Care should

be taken when removing the packaging in order to avoid

scratching the unit’s exterior metal nish.

To remove the wooden pallet, rst if at all possible, we sug-

gest that the cabinet remain bolted to the pallet during all

transportation to the point of nal installation. The bolts can

then be removed with a 3/4” socket wrench. Avoid laying

the unit on its front, side or back for removal of the pallet.

NOTE: DO NOT LAY THE UNIT ON ITS SIDE DURING

TRANSPORTATION OR INSTALLATION.

IV. c - WIRING DIAGRAM:

Refer to the wiring diagram for any service work performed

on the unit. Should you require a wiring diagram, please

contact Traulsen Service at (800) 825-8220, and provide the

model and serial number of the unit involved.

IV. d - INSTALLING LEGS OR CASTERS:

The cabinet must be blocked and stable

before installing legs or casters.

6” high stainless steel legs are supplied standard for models

TBC5 and TBC13. Casters in lieu of legs are available as an

optional accessory for the same models. These are shipped

from the factory packed inside a cardboard box which is

strapped to one of the shelves. Remove the nylon strap and

open the box, it should contain either four (4) legs or casters

(and four bolts for each caster).

IV. INSTALLATION

IV. INSTALLATION (continued)

Fig. 2

Fig. 3

WARNING

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Traulsen TBC5 Blast chiller. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Traulsen. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Traulsen TBC5 Blast chiller in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Traulsen Blast chillers
Meer handleidingen voor Blast chillers

Beoordeling

Gerelateerde producten

Handleiding

Traulsen TBC13 Blast chiller

Handleiding

Traulsen TBC1HR Blast chiller

Handleiding

Traulsen TBC1H Blast chiller

Handleiding

Omcan BC-IT-0103 Blast chiller

Handleiding

Hendi 232187 Blast chiller

Handleiding

Hendi 232170 Blast chiller

Handleiding

Smeg SBC4104G Blast chiller

Handleiding

Omcan BC-IT-0906 Blast chiller

Gerelateerde categorieën