Handleiding Vango Solace 400 Tent

Handleiding

TENT PITCHING INSTRUCTIONS – SOLACE (UK)

Flysheet First Pitching:

 Open out flysheet and position in required direction

 Peg out the four main corners of the tent using the pegs supplied

 Locate inflation points on each beam

 Remove the valve cap (figure 1)

 Insert the correct pump adaptor, which will lock onto the valve (figure 2 & 3)

 There is no need to turn the white valve button as the adaptor will move this to the correct position

 Inflate all tubes to 7psi. The tubes MUST be guided into an arch as they are inflated.

 Final tube pressure MUST NOT exceed 8psi

 DO NOT OVER-INFLATE THE BEAMS

 Start with the center tube and guide the beam into an upright position while it is inflating

 Inflate the other beams.

 A small amount of air may leak from the valve when it is being inflated but this is normal

 Remove the pump adaptor as soon as the beam is at the correct psi

 Replace the valve cap to create an air tight seal (figure 5 & 6)

 Ensure the tent is in a straight line

 The groundsheet should be flat and wrinkle free

 Peg out the remaining poles and pegging points using pin pegs at the base of poles

 Peg out ALL guy lines using pin-pegs ensuring that guy line fabric attachment points are evenly tensioned.

 Reposition and adjust tensioning where necessary

CORRECT PUMP SET-UP:

 Pump Body > Pressure Valve > Pressure Gauge > Hose

 (Ensure the valve/gauge/hose are connected to the inflation port of the pump)

Inner Attachment:

 Open out inner tent inside flysheet and position doorways to correspond with the living area

 Starting from the rear corners of the tent, attach the elasticated hooks on the groundsheet to corresponding rings on the flysheet

 Suspend the inner by attaching toggles of inner tent through rings on inside of flysheet

 Do the rear first and work forward

Tension Band System:

 Remove Tension Band System from pockets and attach into the corresponding clips at the apex of the pole

 Adjust the straps until they are taut

 DO NOT OVERTENSION. Excess tension will alter the shape of the tent

TO DEFLATE AIRBEAM/ AIRAWAY/ AIRAWNING:

 To deflate the AirBeam (remove the cap (figure 7)) press & turn (figure 8) the button from CLOSED to OPEN

In the unlikely event of a puncture:

 Deflate the air beam. Unzip the internal flysheet sleeve which contains the affected beam.

 Remove the tube and its protective outer.

 The zips for the protective outer are cable tied together to prevent accidental access. Cut the cable tie and open the zip.

 DO NOT open these zips when the tube inflated.

 Remove the clear rubberised tube from the protective sleeve taking care when removing the valve from the sleeve.

 Partially inflate the tube and pass through a bucket or basin of water, looking for air bubbles. This will indicate location of puncture

 Use the repair patch provided and cover hole, using instructions on patch. Re-insert tube into protective outer, closing zip from both ends, so that zip pullers

are in the flysheet sleeve (this might be easier with the tube partially inflated)

AIRBEAM INFLATION:

AIRBEAM DEFLATION:

AUFBAUANLEITUNG– SOLACE (DE)

Mit Außenzeltaufbau zuerst:

 Außenzelt auslegen und korrekt ausrichten.

 Befestigen Sie die 4 Hauptecken des Zelts mit Hilfe der mitgelieferten Heringe

 Lokalisieren Inflation Punkte auf jeder Strahl

 Entfernen Sie die Ventilkappe

 Legen Sie die richtige Pumpenadapter , die auf das Ventil sperren wird

 Es besteht keine Notwendigkeit , um die weiße Ventilknopf drehen, da der Adapter wird diese in die richtige Position bewegen

 Pumpen Sie alle Schläuche auf 7psi auf. Die Schläuche MÜSSEN beim Aufpumpen in einen Bogen geformt werden.

 Der Schlauchdruck DARF letztendlich 8psi nicht überschreiten.

 TRÄGER NICHT ZU STARK AUFPUMPEN.

 Beginnen Sie mit dem mittleren Schlauch und bringen Sie den Träger beim Aufpumpen in eine aufrechte Form.

 Pumpen Sie die anderen Träger auf.

Figure 1

Remove

locking cap

Figure 3

Lock locking pump

connector

Figure 4

Inflate with

AirBeam pump

Figure 5

Insert locking

cap

Figure 6

Lock locking cap

Figure 8

Push button to deflate &

twist to open position

Figure 7

Unlock

locking cap

Figure 2

Insert locking pump

connector

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Vango Solace 400 Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Vango. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Vango Solace 400 Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Vango Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Vango Solace 400 Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Vango Tryfan 300 Tent

Handleiding

Vango Tay 300 CLR Tent

Handleiding

Vango Lismore TC 450 Tent

Handleiding

Vango Xenon UL Air Tent

Handleiding

Vango Casa Air Lux Tent

Handleiding

Vango Joro Air 600XL Tent

Handleiding

Vango Ventanas II Air TC 650XL Tent

Handleiding

Vango Orava II 650XL Tent

Gerelateerde categorieën