Handleiding Vetta RT Classic Fietscomputer

Handleiding

RT Classic & RT233

9

RT Classic RT233

Speed (Current)

Speed (Avg / Max)

Cumulative Odometer

Trip Distance

Freeze Frame Memory

LCD Screens

12 /24 Hour Clock

Interchangeable Front Cover

EZ Tire Setup

2

2

Service Timer

HEAD UNIT (RT233)

HEAD UNIT (RT Classic)

Vetta cycle computers are sophisticated electronic instruments. Vetta recommends that

this product be installed only by a qualified bicycle retailer. Failure to read these instructions

and/or improper installation of this device may void the warranty. If in doubt about any

aspect of the installation or operation of this product, consult your local bicycle retailer for

clarification.

RT Classic:

RT233:

Attach the Wired Speed Sensor with the Zip-Ties supplied and tighten the Bladed Spoke

Magnet to the bicycle.

Mounting the sensor as high up on the fork leg as possible. (see

Fig.A).

Adjust the sensor and magnet spacing with the Spacer. Remove the Spacer

after

tightening the Zip-Tie down to hold the sensor in its final position.

MOUNTING BRACKET & HEAD UNIT

Wired Mounting Bracket

Head Unit

Head Unit

UNLOCK

Loocking Tab

Wired Mounting Bracket

UNLOCK

Loocking Tab

Step 1:

Advance the computer to the SPD screen mode using Buttong #2.

Step 2:

Pick up the front of the bicycle and spin the front wheel or ride the bicycle a short distance.

The LCD should display a speed reading within 2-3 seconds.

If there is no speed reading, check the alignment and spacing between the magnet and sensor.

Make sure that the Head Unit is completely locked into position. If these checks do not solve the

problem, talk to an Authorized Vetta’s Retailer or connect to www.vetta.com/support.asp.

CLASSIC

CLASSIC

CLASSIC

8

The head unit is water resistant and sealed to withstand wet weather conditions. However,

do not deliberately place it in water.

Avoid leaving the head unit exposed to extremely hot weather conditions.

Vetta encourages you to ride safely. Wear a helmet every time you ride, use front and rear

lights at night, and always keep your eyes on the road ahead of you.

1

Set / Select Button (Left)

2 Mode / Advance Button (Right)

A Upper Display (Speed)

B Service Timer Icon

C Speed / Distance Units

D Lower Display

E Function Icons

A

Contact Points

B

Battery Compartment

C

Battery Coner

Important:

Use the tapes provided with the package (NOT ZIP-TIES) to hold wires to the

frame, fork, bars or stem to avoid damaging or cutting the wires accidently. Make sure excess

wire is taped down or wrapped around brake cable housing to secure it.

The Head Unit uses a CR2032 3-Volt Lithium

button cell battery.

Battery Run Time (1 hour training / day): Approx. 12 months

Important: Most cycle computer problems are caused by weak or

dead batteries. See the Trouble Shooting section near the end of

the manual for details.

1. Remove the battery cap from the bottom of the

Head Unit using a coin.

2. Install a new battery as shown with the positive

(+) side facing out. Do not touch or bend any

of the battery contacts during installation.

3. Screw the battery cap firmly into place making

sure the O-ring seal does not get pinched or distorted.

Caution: To avoid damage to the battery cap, do not over tighten.

Press momentarily

Press & hold for 2 seconds

1 Set / Select Button (Left)

2 Mode / Advance Button (Right)

Button & when the lowest screen is in the CLK Mode: NOM Setup

1

2

Button & when the lowest screen is in the DST Mode: Reset Ride Data

1

2

Note: Secure wire with tape supplied and by winding it around cables. Be sure to leave

enough slack in the wire to accommodate the movement of fork and handlebars.

Attach Mounting Bracket to the handlebar on the “Sensor Side”. Adjust its position to your liking

and fasten the screw.

Slide the Head Unit into the Wired Mounting Bracket as shown until it clicks into position.

Remove by pressing in the locking tab as shown.

Once installation is complete, the computer should be tested to make sure it is working properly.

Important: Once the sensor is aligned, tighten the magnet’s locking screw and Mounting Bracket

Strap.

Service Timer could be programmed with a selected number of ride

time hours as the interval for servicing the bicycle or any component

on it, such as a front or rear shock.

Accumulated Ride Time is displayed on the upper line and Service

Time is displayed on the lower line. To set the service Time, press

Button #2 to advance hour digits. (The hour digits appear on the

lower level with the right hand digit flashing.) Press Button #1 to

select and advance to next digit. (Maximum hour setting=1999 hours)

The default setting for the Service Timer is “0000” hours, which

means the Service Timer is turned off.

Service Timer could be programmed with a selected number of ride time (hours or days)

or distance as the interval for servicing the bicycle or any component on it, such as a front

or rear shock.

Press to scroll flashing hr (hour), day or dst (distance) as the Service Time unit. Press

to select the desired Service Timer unit.

When the desired Service Timer unit has been chosen, press to scroll the flashing digit

to the desired number. Press to select this number and advance to next digit. Repeat

this procedure until all digits are selected.

Press to advance the next setup Mode. (Maximum settings: hour / day / distance=1999

/ 199 / 9999)

1

2

1

2

1

When the Ride Time (the elapsed time for Service

Timer) or the elapsed

distance begins

to flash, press & hold to reset to zero;

OR press to reserve the digits, and advance to the next Setup Mode.

1

2

Important: In the Initial Setup, the elapsed time [ distance] for Service Timer doesn’t exist.

Press Button #2 to switch between “M/hr” and “KM/hr” and Button #1 to select desired units

and advance. (To change units in SPD / ODO

screen mode, press and hold Buttons #1 and

#2 simultaneously for 2 seconds until “M/hr” begins

to flash).

In Setup, Button is used to select or set a value and to advance to the next digit or Mode.

Button is used to switch between settings and to increase values.

1

1

2

2

RT233 (RT Classic) is programmed to enter the Initial Setup Mode after new battery replacement.

In the Initial Setup, riders can program the Basic Settings for the computer, the content of

settings are same as NOM Setup for Basic Setting.

Initial Setup

NOM Setup

After completed the Initial Setup, riders can change any values or correct any errors by re-entering

the NOM Setup. To enter the NOM Setup Mode, press & hold & simultaneously when the

lowest screen is in the aclk Mode.

Important:

Computer CANNOT exit during the Setup Mode until all the Basic Settings are finished.

Press to toggle between flashing 12 and 24 hour formats. Press to select your desired

format (without PM icon implies AM in 12 hour format) and advance to Time setting.

2

2

2

2

1

1

1

1

Press to advance hour digits to correct hour (hold button for rapid advacne). Press to select

and advance to minute setting. Press to advacne minute digits to correct minute. Press to

select and advance to the next Setup Mode.

Press to toggle between flashing M/hr and KM/hr.

Press to select and advance to teh next Setup

Mode.

1.

Wired Speed Sensor with Mounting Bracket

2. Extra Clear Front Cover

3. Bladed Spoke Magnet

4. Spacer

5. Head Unit Battery (CR2032, 3-Volt)

6. Wire Securing Tape

7. Zip-Ties

8. Screw Strap

1. Button 3. Main Display 5. Battery Compartment

2. Button 4. Contact Pins 6. Battery Cap

1

2

(RT Classic)

(RT Classic)

(RT233)

The default settings “0000” means the Service Timer is turned off.

(RT Classic)

(RT233)

(RT Classic)

(RT Classic)(RT233)

(RT233)(RT233)

(RT233)(RT233)

Universal Bike Mount

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Vetta RT Classic Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Vetta. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Vetta RT Classic Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Vetta Fietscomputers
Meer handleidingen voor Fietscomputers

Beoordeling

Veelgestelde vragen over Vetta RT Classic Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Vetta RT233 Fietscomputer

Handleiding

Vetta RT55 Fietscomputer

Handleiding

Vetta RT277 Fietscomputer

Handleiding

Vetta C350 Fietscomputer

Handleiding

Vetta V80 Fietscomputer

Handleiding

Vetta RT77 Fietscomputer

Handleiding

Vetta RT288L Fietscomputer

Handleiding

Vetta C500 Fietscomputer

Gerelateerde categorieën