Handleiding Westinghouse 6104200 Lamp

Handleiding

W-417

102816

WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a

period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or

implied.

This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration

of components, nor does it cover damages caused through abuse, improper installation, surges in

electric current, or acts of third parties.

This warranty does not cover costs of removing and re-installing the lighting fixture.

If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many

years of beauty and service. For questions and comments, please visit www.westinghouselighting.

com/contact-us.

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

WARNING:

ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.

Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-

tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-

age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are

damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are pro-

vided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985

have supply wires rated 60° C. Consult a qualified electrician before installing.

NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded

type receptacle and is not intended for connection to a two wire ungrounded source of supply.

Owner’s Manual

LED Indoor Lighting Fixture

Installation Instructions

Guide d’utilisation

Instructions d’installation

Appareil d’éclairage pour utilisation intérieure avec LED

GARANTIE LIMITÉE DE CINQ ANS

Cet appareil d’éclairage Westinghouse est assorti d’une garantie de 5 ans contre les défauts de matéri-

aux et de fabrication, qui entre en vigueur à partir de la date d’achat. La présente garantie se substitue

à toute autre garantie expresse ou tacite.

Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la

foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages

survenant suite à une utilisation anormale, une installation impropre, une surtension de courant élec-

trique ou des actes d’un tiers.

Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.

Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez-

nous gratuitement au numéro suivant : 1-888-417-6222.

MISE EN GARDE:

L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.

Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez

pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-

mencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil

d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un

plafond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si l’un des

composants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez pas cet

appareil d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.

Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil

d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se

trouvent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)

NOTA: Pour appareil d’éclairage avec sortie terre. Cet appareil d’éclairage utilise un réceptacle

muni d’un fil de terre et ne doit pas être branché à un bloc d’alimentation à deux fils non mis à

la terre.

LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION INTÉRIEURE

Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d’éclairage a été

conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à

nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.

NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces

y sont avant de mettre l’emballage au rebut (voir fig. 1).

MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures

meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Identify color coding of fixture wires.

3.

Connect the black wire from the fixture with the black wire (live wire) from the outlet box (B) by wire

connector (D), and wrap the wire connector (D) with electrical tape for a more secure connection.

4.

Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (B) by

wire connector (D), and wrap the wire connector (D) with electrical tape for a more secure connection.

5. Partially thread green grounding screw (E) into side hole (F) on mounting plate (C) (see fig.1).

6.

Wrap the bare grounding wire (A) from the fixture canopy (G) around the green grounding screw (E)

on the mounting plate (C) leaving enough excess wire. Connect the greenish grounding wires (A)

from hanging cord and excess grounding wire from the fixture canopy (G) with the grounding wire

from outlet box (B) by using a wire connector (D), then wrap the wire connector (D) with electrical

tape for a more secure connection.

7. Tighten green grounding screw (E). Do not over tighten.

8. Tuck wires inside outlet box (B).

9. Raise mounting plate (C) upto outlet box (B), secure with outlet box screws (A) (included).

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1. Raise canopy (G) up to mounting plate (C), secure with set screws (H).

2. Raise decorative net (J) up to fixture shade (I), secure with clips on decorative net (J).

3. Turn power back on at circuit box.

WARNING

Turn off electricity to the mounting site before beginning installation.

Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can

discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to

clean this fixture.

NOTE FOR FIXTURES THAT ARE SOLID BRASS:

Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-

quer which gives maximum protection against the weather. However, in time the brightness of the

brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture

looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-

faces, giving the fixture an extra protective covering.

ADJUSTING LENGTH OF CORD

These steps should only be performed by someone familiar with working with electrical wiring. Care

must be taken when adjusting the length of the cord to ensure insulation on internal wires is not

damaged. If not familiar with these steps, seek the aid of a qualified electrician.

1. Remove Wire Connectors (M) connecting end of cord to wires from the box attached to the

Mounting Plate (C). Note which color wires are connected in each Connector.

2. Loosen the screw in strain relief (K) until cord slides easily, being careful not to completely remove

screw. Slide canopy down cord until the fixture is the correct distance below the canopy. Tighten

the screw in the strain relief until cord does not slide.

3. Slide cord through one side of Cord Lock (L) until Cord Lock is nearly touching the top of the strain

relief (K). Slide cord through the other side of the cord lock until it locks in place.

4. Cut cord approximately two to three inches (2”-3”) above Cord Lock.

5. Leaving at least one inch (1”) of outer insulation above the Cord Lock, carefully cut through outer

insulation of cord, being careful not to damage inner insulation. Remove outer insulation. Strip

inner insulation from end of both wires, leaving approximately 1/2 inch of wire exposed.

6. Attach new cord ends to the wires from the box attached to the Mounting Plate (C), using Wire

Connectors (M) removed earlier, matching colors as previously noted. Tape Connectors for more

secure connection.

ORDERING PARTS

Keep this manual for future reference, and in case replacement parts are needed. Available parts can

be ordered from place of purchase. Use exact wording from diagrams when ordering parts.

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com

, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.

Used under license by Westinghouse Lighting. All rights reserved. Made in China

*OUTLET

BOX (B)

MOUNTING

PLATE (C)

CANOPY (G)

SHADE (I)

DECORATIVE

NET (J)

GREEN

GROUNDING

SCREW (E)

WIRE

CONNECTORS (D)

WIRE

CONNECTORS (M)

STRAIN RELIEF (K)

GROUND

WIRE (A)

OUTLET BOX

SCREWS (A)

SET SCREW (H)

CORD LOCK (L)

SIDE

HOLE (F)

*NOT SUPPLIED

Line art shown may not exactly match the

fixture enclosed. However, the installation

instructions do apply to this fixture.

FIGURE 1.

*BOITE DE SORTIE

DE COURANT (B)

PLAQUE DE

MONTAGE (C)

SERRE-CÂBLE (K)

CHAPEAU (G)

ABAT-JOUR (I)

FILET

DÉCORATIF (J)

VIS DE MISE

A LA TERRE

(VERTE) (E)

CONNECTEURS

DE FIL (D)

CONNECTEURS (M)

FIL DE MISE

A LA TERRE (A)

VIS DE LA BOITE DE

SORTIE DE COURANT (A)

VIS DE

CALAGE (H)

DISPOSITIF DE

BLOCAGE DU

CORDON (L)

TROU

LATERAL (F)

*NON FOURNI

Il est possible que le dessin illustré ici ne

soit pas la reproduction exacte de l’appareil

d’éclairage contenu dans la boîte.

Les instructions d’installation demeurent

cependant valables.

FIGURE 1.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Westinghouse 6104200 Lamp. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Westinghouse. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Westinghouse 6104200 Lamp in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Westinghouse Lampen
Meer handleidingen voor Lampen

Veelgestelde vragen over Westinghouse 6104200 Lamp

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Westinghouse 6401240 Lamp

Handleiding

Westinghouse 6348840 Lamp

Handleiding

Westinghouse 6577540 Lamp

Handleiding

Westinghouse 6362440 Lamp

Handleiding

Westinghouse 6113140 Lamp

Handleiding

Westinghouse 6121640 Lamp

Handleiding

Westinghouse 6580940 Lamp

Handleiding

Westinghouse 6124840 Lamp

Gerelateerde categorieën