Handleiding Watts BT-DRF-02 Thermostaat

Handleiding

PPLIMW15250Ba

BT-DRF-02

IMPORTANT!

Before starting work the installer should carefully read this Installation & Operation

Manual, and make sure all instructions contained therein are understood and observed.

- The thermostat should be mounted and maintained by specially trained personnel only.

People in the course of training are only allowed to handle the product under the

supervision of an experienced fitter. Subject to observation of the above terms, the

manufacture shall assume the liability for the equipment as provided by legal terms.

- All instructions in this Installation & Operation manual should be observed when

working with the controller. Any other application shall not comply with the regulations.

The manufacturer shall not be liable in case of incompetent use of the control. Any

modifications and amendments are not allowed for safety reasons.

The maintenance may be performed by service shops approved by the manufacturer

only.

- The controller functionality depends on the model and equipment. This installation

leaflet is part of the product and has to be obtained.

APPLICATION

- The thermostats range “BT-DRF-02” has been developed to control and manage all

type of Electrical heating system or materials.

- The controllers have been designed for use in residential rooms, office spaces and

industrial facilities.

Please find the Watts Vision system configuration documentation on:

http://www.wattselectronics.com

Table of content

1 Presentation

1.1 Keyboard

1.2 LED & Display

2 First Installation

2.1 Batteries installation

2.2 RF installation

2.2.1 With receivers

2.2.2 Case of central

2.3 Starting

3 Working mode definition

3.1 Manual mode Comfort

3.2 Manual mode Reduced

3.3 OFF mode

3.4 Anti-freeze mode

3.5 Timer mode

3.6 Reversible mode

3.7 AUTO mode

4 Special function

4.1 Keyboards lock Function

4.2 Open window function

4.3 Humidity measurement

4.4 Visualization

5 Parameter’s menu

6 Technical characteristics

7 Troubleshooting & Solution

8 Advanced installer’s parameters menu

1 Presentation

Electronic thermostat with LCD display specially designed to control different type of

heating systems.

It will be your best partner to optimize your energy consumption and increase your

comfort.

- Modern design with soft touch material

- Wireless Bidirectional communication 868 MHz

- Temporary override function

- Anti freeze function.

- EEPROM non volatile memory

- 2 AAA batteries

- 2 parameter menus (User and Installer)

- Humidity measurement (*)

In option

External sensor with several possibilities of regulation (Floor, combined…)

1.1 Keyboard

Left Navigation key (◄)

Right navigation key (►)

Escape key ( )

Edition key ( )

1.2 LED & Display

Color of “OK” LED when backlight is lit up:

Red Fix: heating demand (**)

Green Fix: cooling demand (**)

Green flash: validation is required

Red flash: error on sensor or batteries

1. Operating mode menu (active mode is framed).

2. Parameter number if “3” is displayed.

3. Installation Parameter menu.

4. Type of used sensor and displayed temperature

Regulation => Internal sensor.

Regulation => Floor sensor (Only available with receiver)

Regulation => Internal sensor with Floor limitation.

Regulation => outside temperature measured by external sensor (connected on the

back of thermostat)

Visualization of the humidity percentage (*)

5. Heating demand indication (**)

6. Cooling demand indication (**)

7. Low batteries indicator

8. °C or °F unit indicator

9. Setting or measured temperature if “4” is displayed.

Give the parameter name/value if “3” is displayed

10. Key lock indicator

11. RF indicator

2 First Installation

This section will guide you to set up your thermostat for the first time.

2.1 Batteries installation

- Open the two side’s covers and insert the 2 AAA Alkaline supplied batteries (or remove

the small protection sticker if the batteries are already installed in the compartment)

- Close the two side’s covers.

2.2 RF installation

Please have a look at the list of all receivers compatible with this thermostat in Technical

Caracteristics section.

2.2.1 With receivers

- First of all to configure your thermostat with the receiver, you must put your receiver in

RF init mode. (refer to the receiver leaflet, only the RF receivers of the same range are

compatibles)

- Press and maintain the edition key ( ) during 5s, then the parameter « INI » must be

displayed.

The thermostat will send now the radio configuration signal to the receiver.

- After few seconds, the thermostat and the receiver should exit by their self the RF init

mode, this is the normal procedure to confirm a correct pairing.

- You can check the RF distance. Go to the room which must be regulated. Put your

thermostat on the final position (On the wall or table...), then put the thermostat in

Comfort mode (setting temperature position 37°C). Close the door and go to the receiver

to check if the new thermostat status has received.

- Return to the thermostat and switch it off. Check on the receiver again if it’s also

switched off.

If the RF signals were received correctly, adjust your setting temperature as you want.

If the RF signals weren’t received correctly, check the installation (Receiver position,

distance...) or restart the RF init rules to be sure.

Remark: To make the installation easier, it will be better to have the thermostat near to

the receiver during the configuration mode (a minimal distance of 1 meter must be

respected).

2.2.2 Case of central (BT-CT02)

The link is done with central (BT-CT02).

2.3 Starting

The thermostat is now ready to work. Default working mode is Comfort mode

3 Working mode definition

Your thermostat has several different working modes to allow you to adjust your unit

according to your life habitudes.

To change the working mode, open the small center

cover to access to the navigation keys (◄) or (►). Move

the frame cursor on the desired working mode and press

(OK) to enter in the chosen operating mode.

3.1 Manual mode Comfort

Manual working mode, the comfort setting temperature will be followed all the time.

By pressing (-) or (+) keys, the comfort setting temperature starts to blink and can be

adjusted.

Remark: Setpoint in Comfort mode is used in

mode

3.2 Manual mode Reduced

Manual working mode, the reduced setting temperature will be followed all the time.

By pressing (-) or (+) keys, the reduced setting temperature starts to blink and can be

adjusted.

Remarks:

- Setpoint in Reduced mode is used in

mode

- In cooling mode, Reduced mode acts like the OFF mode (system is stopped)

3.3 OFF mode

Use this mode if you need to switch off your installation.

Be Careful: In this mode your installation can freeze.

At any time, when display is off, press on the (Ok) key to display a few seconds the

current temperature and time.

Remark: To exit the operating mode, use the navigation keys (◄) or (►).

3.4 Anti-freeze mode

Use this mode if you want to protect your installation against freezing.

- The anti-freeze setting temperature is fixed and can be adjusted in the parameter

menu number 06 ‘HG’, refer to chapter 5 (Default value 10°C).

Remark: in cooling mode, Anti-freeze mode acts like the OFF mode (installation is

stopped).

3.5 Timer mode

The Timer mode allows you to adjust, the temperature for a special time. After this time,

thermostat will return to older current mode.

- You can first adjust, the desired setting temperature with (-) or (+), press (OK) to

validate (Default value 24°C)

- In a second time, you can adjust the duration in hours “H” if below 24H, then in day “d”

with (-) or (+), press (OK) to start the function.

The logo will blink and the number of hours /days left is displayed until the end of the

period.

If you want to stop the Timer function before the end, set the duration period to “no”

with (-) key or use the navigation keys (◄) or (►).

3.6 Reversible mode

The reversible mode allows you to choose the working mode for your installation.

By pressing on (-) or (+) keys, the selected working mode blinks and can be modified.

The user can choose:

- Hot: the installation operates in heating mode (winter)

- CLd: the installation operates in cooling mode (summer).

During this selection, the status LED will be red color if heating is selected or green color

if cooling is selected.

By pressing (OK) key, you validate you selection. By pressing (◄) or (►) key or the

( ) key, you come back to the current working mode of the thermostat.

Remarks:

- This menu is only available if the parameter “21” has been set to “REv” (refer to

chapter 8)

- This mode is not available if thermostat is linked with a central (BT-CT02)

3.7 AUTO mode

This mode appears when if a central is linked to your installation. In this case, the zone

of the thermostat follows the program created on the Central (BT-CT02).

4 Special function

4.1 Keyboards lock Function

Use this function to prevent all change of your settings (In a child room, public area…)

- To activate the Key lock function, first maintain the escape key ( ) pressed and press

simultaneously on the edition key ( ).

- The “ ” logo will be displayed on the screen.

Repeat the same procedure to unlock the key board.

4.2 Open window function

This function is able to stop heating if thermostat detects an unusual decrease of

temperature (open window).

Principle:

If the displayed temperature (internal or ambient sensor) decreases by 3°C or more

during a 5 minutes period (or less), the thermostat stops heating for 15 minutes. If the

temperature continues decreasing, it continues to stop.

During this stop, the room temperature will blink.

Return to normal mode:

The thermostat returns automatically to normal mode after the stop period.

The function can be overridden by pressing the (OK) button during the stop heating

phase.

The blinking temperature should stop to indicate the end of the detection.

Special cases:

- This function doesn't work if Thermostat is in Floor regulation

- This function doesn't work if Thermostat is in OFF / Antifreeze Mode

- If temperature is less than 10°C, thermostat will regulates at 10°C during the stop

phase (refer to chapter 5, parameter 06)

- This function doesn’t work in cooling configuration

4.3 Humidity measurement (*)

Thermostats measure the humidity in the air. This measure allows:

- To regulate the humidity in the air (refer to parameter 34 chapter 8)

- To protect your system against condensation (refer to parameter 35 chapter 8).

4.4 Visualization

With this function, you can quickly view the current temperatures of the different sensors

connected to your thermostat (floor, remote, external). On the main screen, press

several times on the escape key ( ). This “scroll function” is only available on the main

screen:

You will see in the order of each press:

1/ the setting temperature followed by the thermostat

2/ the ambient temperature

3/ if the external sensor is connected: the outside temperature

4/ the humidity percentage (*)

Remarks :

- refer to chapter 1.2 for icon meanings

- if Parameter “Sen” is set on “Air” (refer to chapter 8), the remote sensor will be used as

an external sensor.

Minus Key (-)

Plus Key (+)

Validation Key (OK)

Status LED

GB

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Watts BT-DRF-02 Thermostaat. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Watts. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Watts BT-DRF-02 Thermostaat in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Watts Thermostaten
Meer handleidingen voor Thermostaten

Veelgestelde vragen over Watts BT-DRF-02 Thermostaat

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Watts BT 051 Chrono Battery Thermostaat

Handleiding

Watts BT 050 Chrono Battery Thermostaat

Handleiding

Watts BT-DPRF-02 Thermostaat

Handleiding

Watts BT DPRF-01 Thermostaat

Handleiding

IMIT CRD/503N Thermostaat

Handleiding

Fantini Cosmi CH140GSM Thermostaat

Handleiding

BTicino NT4466 Thermostaat

Handleiding

Fantini Cosmi C76B Intellitherm Thermostaat

Gerelateerde categorieën