Handleiding Barska AX11648 Kluis

Handleiding

User’s Manual for

Biometric/Key Pad Safe

WARNING

- Safe can be opened by either Fingerprint, PIN code,

and/or Emergency Keys.

- If user resets the safe to Factory Default mode: ANY

fingerprint and Factory Default PIN code can open

the safe.

- Register both Fingerprint and PIN code to disable

Factory Default mode.

- Register at least two different fingerprints and test a few

times before closing the safe door.

- Test with a non-registered fingerprint. If the safe opens,

the safe is still in Factory Default mode.

- Avoid leaving safe door open and unattended; it will allow

unauthorized individuals to add their fingerprints and/or

reprogram the safe, gaining full access to the safe and

the contents.

- Test the Emergency Keys and store them in a secure

place, NOT inside of the safe.

- To maximize the security and performance of the safe,

test registered fingerprints every 6 months.

Read all instructions before using this safe.

A. Initialization Button

B. Battery Compartment

C. Bolts

D. Fingerprint Scanner

E. Indicator Lights

A

B

C

I

D

F

G

E

H

F. Enter Button

G. Key Pad

H. Knob

I. Logo Plate and

Emergency Key Access

* Actual model may vary

GETTING STARTED

1. Remove Emergency Keys from accessory package

- To expose the Emergency Key Access, remove Logo Plate

(I) screws with provided tool

- Insert Emergency Key into key access, push and turn

counter-clockwise

- Turn the Knob (H) clockwise to open

Note: Store Emergency Keys in a secure place, NOT inside of

the safe

2. Continue with INSTALL BATTERIES

INSTALL BATTERIES

1. With safe door open, remove Battery Compartment (B) cover

- Insert 4 AA batteries and restore battery cover

- Continue with FINGERPRINT REGISTRATION

FINGERPRINT REGISTRATION

IMPORTANT: The safe is in either Factory Default mode or

Pre-registered mode, test safe to determine factory settings

below

Factory Default mode: Safe can be opened with ANY

fingerprint(s)

Pre-registered mode: Safe can NOT open with any fingerprint(s)

During registration the door must remain open and Bolts (C)

must be in the retracted position. Otherwise, the fingerprint will

not be saved

To retract bolts:

- Insert Emergency Key into key access, push and turn

counter-clockwise

- Turn the Knob (H) clockwise to retract bolts

1. Press and release Initialization Button (A)

2. Immediately place a finger on the Fingerprint Scanner (D)

- Hold finger still

- Two beeps will be heard recognizing the fingerprint; followed

by one long beep

- Remove finger

- Registration is complete

Successful Registration

Registration is successful when two short beeps are heard,

followed by one long beep

Unsuccessful Registration

Registration failed if two short beeps are heard, followed by

three short beeps

3. To register another fingerprint, repeat steps 1 - 2

4. Continue with TEST A (NON) REGISTERED FINGERPRINT

Fingerprint Memory Full

If the Indicator Lights (E) flash and beep twice followed by a few

green flashes, it indicates the memory is full. Refer to DELETE

STORED FINGERPRINTS AND PIN CODE / RESET TO

FACTORY DEFAULT MODE for more options

TEST A (NON) REGISTERED FINGERPRINT

1. Test multiple Non-Registered fingerprints

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, press and release Enter

Button (F)

- Place a non-registered finger on the Fingerprint Scanner (D)

- Door should NOT open; three short beeps will be heard

- If the door opens with a non-registered fingerprint,

registration was unsuccessful; the safe remains in Factory

Default mode

IMPORTANT: If registration was unsuccessful repeat steps

under FINGERPRINT REGISTRATION, and test non-registered

fingerprint

2. Test Registered fingerprint

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, press and release Enter

Button (F)

- Place a registered finger on the Fingerprint Scanner (D)

- Door should OPEN, one long beep will be heard, turn the

Knob (H) clockwise to open the safe

- Fingerprint registration was successful

3. Continue with PIN CODE REGISTRATION

PIN CODE REGISTRATION

IMPORTANT: Safe only retains one PIN code; Factory Default

PIN code is 1234

1. Press and HOLD number “1” key until the green Indicator

Light (E) turns on, release button

- Enter Factory Default PIN code 1234, press Enter Button

(F), one long beep will be heard

- Enter new PIN code (four to eight digits), press Enter Button

(F), two short beeps will be heard

- Re-enter new PIN code, press Enter Button (F), one long

beep will be heard

- Registration is complete

2. If you hear three short beeps with red/green Indicator Lights

(E) flashing, it indicates the new PIN code registration was

unsuccessful, repeat step 1

3. Continue with TEST A (NON) REGISTERED PIN CODE

See reverse side for more information

10/12

BC256

U

n

l

o

c

k

L

o

c

k

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Barska AX11648 Kluis. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Barska. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Barska AX11648 Kluis in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Barska Kluizen
Meer handleidingen voor Kluizen

Veelgestelde vragen over Barska AX11648 Kluis

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.