Handleiding Barska AX11970 Kluis

Handleiding

PARTS OF THE SAFE

Parts of the Safe

A. Key Entry

B. Indicator Light

C. Fingerprint Scanner

D. Wake Up Button

E. Initialization Button

F. Battery Compartment

and Cover

G. Cable Slot

H. Mounting Holes

(located under the safe)

See reverse side for more information

A

B

C

D

F

G

E

8/12

BC239

H

OPENING THE SAFE WITH ACCESS KEY

1. Insert access key into key entry, turn clockwise to open,

partially lift lid of safe and remove access key by turning it

counter clockwise

2. Open safe by lifting the lid of the safe

NOTE

Store access keys in a secure place. NOT inside of safe

When calling for replacement or additional access keys have

the access key code number ready. The access key code is

etched in the key entry and on the access keys.

BATTERIES

1. Locate the battery compartment and remove battery cover

2. Gently slide battery holder out of the compartment

3. Place 4, AA batteries and pay attention to the polarity of

each battery

4. Gently slide battery holder back into place

5. Replace battery cover

REPLACING BATTERIES

The red indicator light will start flashing and a continuous

beeping sound will be heard. This indicates that the batteries

are low.

1. Open safe by using the access key; turn clockwise

2. Repeat steps 1-5 of “Batteries” and replace old batteries with

new batteries

3. Close safe and ensure that the safe is locked

NOTE

After replacing the batteries safe retains registered fingerprints

REGISTERING A FINGERPRINT

The safe is in demo mode, ANY fingerprint can open the safe

1. With the safe open press and release the initialization button

2. A beep will be heard and scanner will flash red

3. Immediately place desired finger on the scanner

- Hold finger still, until registration process is complete

4. Registration process is complete when a total three beeps

are heard. See below

Successful Save

- Indicator light will flash green, followed by one beep,

indicator light will flash green twice and two

consecutive beeps

- Registration has been successful

Unsuccessful Save

- Indicator light will flash green, followed by one beep,

indicator light will flash red and two consecutive beeps

- Repeat registration process again

NOTE

- To add more fingerprints/users repeat steps above

- Stores up to 120 fingerprints

- For security purposes wipe fingerprint off scanner

For Accurate and Consistent Fingerprint Scanning

- Use scanner in low light conditions

- Use the index finger

- Place and hold finger firmly on the scanner

- Each user should register 2-3 different fingerprints

TESTING A REGISTERING A FINGERPRINT

1. With safe lid open, press the wake up button

2. Place registered finger on the scanner

Successfully Saved Fingerprint

- Indicator light will flash green indicating a valid fingerprint

- You will hear the safe unlock

Unsuccessful Fingerprint

- Indicator light will flash red and green consecutively

indicating that the fingerprint in not valid

- Repeat steps in “Registering A Fingerprint”

4. Close safe and ensure that the safe is locked

5. For security purposes wipe fingerprint off scanner

OPENING THE SAFE USING A FINGERPRINT

1. Press the wake up button

2. Place registered finger on the scanner

3. The indicator light will flash green indicating a valid fingerprint

4. Gently lift the door of the safe

5. Close safe and ensure that the safe is locked

6. For security purposes wipe fingerprint off scanner

DELETING ALL FINGERPRINTS

1. With the safe open locate the battery compartment and

remove battery cover

2. Gently slide battery holder of out of the compartment

3. Remove all 4, AA batteries from battery holder

4. Press wake up button a few times to release remaining

electronic power

5. Re-insert 3, AA batteries and pay attention to the polarity of

each battery

6. Press and hold down the initialization button

7. Re-insert the last AA battery you will hear 2 beeps, release

initialization button

8. Gently slide battery holder back into place and replace

battery cover

WARNING

Avoid leaving safe door open and unattended; it will allow

unauthorized individuals to add their fingerprint and/or

reprogram the safe, gaining full access to the safe and the

contents.

User Manual For Portable

Biometric Compact Safe

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Barska AX11970 Kluis. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Barska. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Barska AX11970 Kluis in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Barska Kluizen
Meer handleidingen voor Kluizen

Veelgestelde vragen over Barska AX11970 Kluis

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.