Handleiding Basetech 3DP1 3D Pen

Handleiding

• As power supply, only use the supplied mains adaptor.

• Only connect the power adaptor to a normal mains socket connected to the public

supply.

• Before plugging in the power adaptor, check whether the voltage stated on the

power adaptor complies with the voltage of your electricity supplier.

• Never connect or disconnect power adaptors if your hands are wet.

• Never unplug the power adaptor from the mains socket by pulling on the cable;

always use the grips on the plug.

• When setting up the product, make sure that the cable is not pinched, kinked or

damaged by sharp edges.

• Always lay the cables so that nobody can trip over or become entangled in them.

This poses a risk of injury.

• For safety reasons, disconnect the power adaptor from the mains socket during

storms.

• If the wall plug transformer is damaged, do not touch it; there is danger to life from

electric shock! First, switch off the mains voltage to the mains socket to which the

wall plug transformer is connected (switch off at the corresponding circuit breaker

or remove the safety fuse, then switch off at the corresponding RCD protective

switch, so that all poles of the mains socket are disconnected). You can then

unplug the wall plug transformer from the mains socket. Dispose of the faulty

wall plug transformer in an environmentally friendly way; do not use it any more.

Replace it with a wall plug transformer of the same design.

• Never use the product immediately after it has been brought from a cold room into

a warm one. The condensation generated could destroy the product. The plug-in

power supply unit also involves danger to life by electric shock! Allow the product

to reach room temperature before connecting it to the power supply and putting it

to use. This may take several hours.

• Never pour any liquids over electrical devices or put objects lled with liquid

right next to the device. If liquid or an object enters the interior of the device

nevertheless, rst power down the respective socket (e.g. switch off circuit

breaker) and then pull the mains plug from the mains socket. Do not operate the

product anymore afterwards, but take it to a specialist workshop.

• In schools, training facilities, hobby or self-service workshops, handling of

electrical devices must be monitored by trained personnel.

• When operating on commercial premises, the relevant accident prevention

regulations of workers’ compensation boards for electrical equipment must be

observed.

• Consult an expert when in doubt about the operation, safety or connection of the

appliance.

• Maintenance, modications and repairs must only be completed by a technician

or an authorised repair centre.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

Operating elements

1

2

3

9

4

5

8

6

7

1 Feed opening

2 DC-socket

3 Temperature and material control

4 LED heating indicator green

5 LED operation indicator red

6 Unload button

7 Speed control

8 Feed button

9 Nozzle tip

Operating Instructions

3D Printing Pen 3DP1

Item No. 1646098

Intended use

The product is used to create three-dimensional objects made of plastic lament. A heating

element inside the pen heats the plastic lament. At the push of a button, the nozzle extrudes

a thin thread of lament that hardens in the air. The product is powered via the power adaptor

which is included in delivery.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.

in bathrooms) must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged. In

addition, improper use can result in short circuits, res, electric shocks or other hazards. Read

the instructions carefully and store them in a safe place. Make this product available to third

parties only together with its operating instructions.

This product complies with the statutory national and European requirements. All company

names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• 3D printing pen

• Small plastic tool

• 3x PLA-lament (3 m)

• 2x stencil

• Power adapter

• USB cable (1.2 m)

• Operating instructions

Up-to-date Operating Instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code

shown. Follow the instructions on the website.

Explanation of symbols

The symbol with the lightning in the triangle is used if there is a risk to your health,

e.g. due to an electric shock.

The symbol with the exclamation mark in the triangle is used to indicate important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on operation.

This symbol warns you of hot surfaces.

Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on

proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

• This appliance may be used by children over 8 years of age and people with

reduced physical, sensory or mental capabilities if they have been given

supervision or instruction concerning the safe use of the appliance and understand

the potential hazards.

• Children must not clean or service the product without appropriate supervision.

• Children should always be supervised by an adult to ensure that they do not play

with the appliance.

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, steam and solvents.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Do not place the product under any mechanical stress.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• Feed only suitable lament into the feed opening.

• Caution. Do not touch the nozzle tip during operation because it is very hot. Risk

of burns!

• The mains outlet must be located near to the device and be easily accessible.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Basetech 3DP1 3D Pen. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Basetech. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Basetech 3DP1 3D Pen in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Basetech 3D Pennen
Meer handleidingen voor 3D Pennen

Beoordeling

Gerelateerde producten

Handleiding

Velleman 3DPEN 3D Pen

Handleiding

3D&Print Pro 3D Pen

Handleiding

Polaroid Play 3D Pen

Handleiding

Velleman 3DPEN1 3D Pen

Handleiding

Gembird 3DP-PEN-01 3D Pen

Handleiding

Hamilton Buhl MPEN 3D Magic 3D Pen

Handleiding

Monoprice MP Select 3D Pen

Handleiding

Gembird 3DP-PEND-02 3D Pen

Gerelateerde categorieën