Home > Diversen > Rookmachines > BeamZ Rookmachines > BeamZ 160.491 S1200 MKII Rookmachine

Handleiding BeamZ 160.491 S1200 MKII Rookmachine

Handleiding voor je BeamZ 160.491 S1200 MKII Rookmachine nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 1 comment en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

- 3 -

Warning

- The smokemachine must be placed at least 100 cm away from inflammable materials such as curtains,

books, etc. Make sure that the housing cannot be touched by accident.

- For indoor use only.

- During installation, nobody should stand beneath the mounting area.

- Prior to the first use, have the unit checked by a qualified person.

- The unit contains voltage carrying parts. DO NOT open the smokemachine

- Never plug or unplug the unit with wet hands.

- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.

- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains

outlet. It needs to be repaired by a qualified technician.

- Only connect this unit to an earthed mains outlet of 230Vac/50Hz .

- Always unplug the unit during a thunderstorm or when it is not in use.

- If the unit has not been used for a longer period of time, condensation can occur inside the housing.

Please let the unit reach room temperature prior to use.

- When you unplug the unit from the mains always pull the plug, never the lead.

- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid

chain, a steel cable, etc. which has to be fastened separately from the mounting bracket.

- The supplied bracket is the main fixing and must be used to solidly mount the light effect.

- In order to avoid accidents in public premises, the local legal requirements and safety

regulations/warnings must be fulfilled.

- Keep out of the reach of children.

Safety

Plug the smoke machine only in an earthed mains outlet or extension cord! ATTENTION: the powercord can

only be replaced by an original replacement, supplied by Tronios. Be careful when filling the fluid tank. First of

all, unplug the mains lead! Then unscrew the cap on the tank and fill it by means of a funnel. Only use the

original Beamz smoke fluid which is environmental friendly and, if used correctly, leaves no residues. Do not

obstruct the openings on top of the case to guarantee a good ventilation. The heating element of the smoke

machine generates heat which needs to be removed. Don’t put any objects on the smoke machine.

Installation and Use

Unpack the fog machine. Fill the fluid tank by means of a funnel. Plug the unit into a mains outlet. Thus the

heating element is automatically switched on. Depending on the room temperature, it takes about 5 until the

working temperature is reached. Then the thermostat is clicking and the LED on the manual control lights up.

Push the switch once and the smoke machine will produce a nice thick fog. Once the smoke machine has

reached its working temperature (the LED is lit) the smoke machine can produce continuously fog during about

1 minute.

After this period of time, the fog generator is cooled so much down that the thermostat switches off. Wait a few

minutes until the working temperature is reached again. It is recommended to produce smoke with small pauses

in between so that the temperature is maintained and the thermostat doesn’t switch off.

Location

Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied

holder and fixing screws.

Switching the unit off

Switch the unit off by unplugging it from the mains. Otherwise the 1200W heating element will draw

unnecessarily current.

Timer remote control

After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may

happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.

Timer function:

Press the yellow button and set the interval, duration and volume controls to the desired level.

Interval: time between the smoke moments (10-200 seconds)

Volume: amount of smoke (0-100%)

Beoordeling

Laat ons weten wat je van de BeamZ 160.491 S1200 MKII Rookmachine vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de BeamZ 160.491 S1200 MKII Rookmachine?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de BeamZ 160.491 S1200 MKII Rookmachine. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

David mason 09-12-2021
Mijn rookmachine maakt een hard knarsend geluid en produceert geen rook. Vloeistof is vol en correct

beantwoord | Ik vind dit nuttig (0) (Vertaald door Google)

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je BeamZ 160.491 S1200 MKII Rookmachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met BeamZ. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van BeamZ 160.491 S1200 MKII Rookmachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.