Handleiding Black and Decker D6000 Strijkijzer

Handleiding

Please Read and Save this Use and Care Book.

IMPORTANT SAFETY

INSTRUCTIONS

When using your iron, basic safety precautions should always

be followed, including the following:

•READ ALL INSTRUCTIONS BEFORE USING.

•Use iron only for its intended use.

•To protect against a risk of electric shock, do not immerse the

iron in water or other liquid.

•The iron should always be turned off (refer to How to Use

section) before plugging or unplugging from outlet. Never yank

cord to disconnect from outlet; instead grasp plug and pull to

disconnect.

•Do not allow cord to touch hot surfaces. Let iron cool completely

before putting away. Loop cord loosely around the iron when

storing.

•Always disconnect iron from electrical outlet when filling with

water or emptying, and when not in use.

•Do not operate iron with a damaged cord, or if the iron has been

dropped or damaged. To avoid the risk of electric shock, do not

disassemble the iron, take it to a qualified service person for

examination and repair. Incorrect reassembly can cause a risk of

electric shock when the iron is used.

•Close supervision is necessary for any appliance being used by

or near children. Do not leave iron unattended while connected

or on an ironing board.

•Burns can occur from touching hot metal parts, hot water, or

steam. Use caution when you turn a steam iron upside down

or use the surgeof steam - there may be hot water in the water

tank. Avoid rapid movement of iron to minimize hot water

spillage.

•The iron must be used and rested on a stable surface.

- When placing the iron on its stand, ensure that the surface on

which the stand is placed is stable.

- The iron is not to be used if it has been dropped,

if there are visible signs of damage or if it is leaking.

SPECIAL INSTRUCTIONS

•To avoid a circuit overload, do not operate another high-wattage

appliance on the same circuit.

•If an extension cord is absolutely necessary, a cord rated at

15-amperes and 120-volt, or a 7-ampere and 220-volt cord

should be used. Cords rated for less amperage may overheat.

Care should be taken to arrange the cord so that it cannot be

pulled or tripped over.

SAVE THESE INSTRUCTIONS.

This product is for household use only.

POLARIZED PLUG (120V MODELS ONLY)

This appliance has a polarized plug (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit

into a polarized outlet only one way. If the plug does not fit fully into

the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Do not attempt to modify the plug in any way.

TAMPER-RESISTANT SCREW

Warning: This appliance is equipped with a tamper-resistant screw to

prevent removal of the outer cover. To reduce the risk of fire or electric

shock, do not attempt to remove the outer cover. There are no user-

serviceable parts inside. Repair should be done only by authorized

service personnel.

Note:

If the power supply cord is damaged, it should be replaced

by qualified personnel or in Latin America by an authorized service

center.

HOW TO USE

This appliance is intended for household use only.

GETTING STARTED

• Remove all labels, tags and stickers attached to the body, cord or soleplate of

the iron.

• Please go to www.prodprotect.com/applica to register your warranty.

• Remove and save literature.

• If ironing dry, place appliance on its heel rest on a stable ironing board.

• Uncoil cord and plug into standard electrical outlet.

Important: For optimum performance, allow the iron to stand for 90

seconds until the Standby

symbol in the bottom right of the LCD

display changes to Ready .

FILLING WATER TANK

1. With iron on flat surface with soleplate down, open

water-fill cover (A).

2. Tilt the iron and using a clean measuring cup, pour

water into opened chamber until water reaches the

MAX level mark on the side of the water tank (B). Do

not overfill.

Note: This iron can be filled with ordinary tap water; if

your water is hard or soft, you may want to use distilled

water. Do not use water processed through a home

softening system.

3. Close the water-fill cover.

Note: If you need to add water while ironing, unplug the iron and follow the

above steps.

4. Plug the iron into an electrical outlet

• The iron beeps.

• The backlight illuminates and turns off.

The Standby

symbol remains on the LCD display

(C).

5. Turn on the iron by pressing the (+) temperature control button, located to

the left of the LCD display (D).

• The iron beeps.

• The LCD backlight turns on.

• The iron begins to heat up and the LCD displays the

lowest heat setting.

SELECTING FABRIC TEMPERATURE

1. Read fabric labels to help determine fabric type to be

ironed.

Tip: If unsure of fabric’s fiber content, test a small area (on the inside seam

or hem) before proceeding to iron the entire garment or cloth.

2. Once you determine the fabric type, press the (+) and

(-) fabric selector buttons on either side of the LCD

display to select the appropriate fabric setting (E).

The LCD display will light up and the fabric type will

appear at the top with the corresponding number for

the setting below it to the left. There will be a flashing arrow

▲

to show the

iron is heating. When the iron is heated, the iron will beep and the Standby

symbol will change to Ready and the arrow will disappear.

3. Whenever the temperature setting is changed, the

▲

or

▼

symbols will

appear on the LCD to show that the iron is either heating up or cooling

down to the newly selected setting.

Important: Always stand the iron on its heel when powered on but not

in use.

STEAM SELECTION

1. The steam symbol can be displayed by pressing the

Steam On/Off button, which is located just behind

the LED display and in front of the steam and spray

buttons (F).

2. ALL-TEMP STEAM® enables you to use steam on all

settings. There will be one burst of steam displayed

on the LCD when using fabric settings 1 through 3 (G). There will be two

bursts of steam displayed when using fabric settings

4 through 7 (H).

3. The steam symbol on the LCD display will blink until

the iron reaches the appropriate temperature. It then

remains constant.

4. If changing the setting from 1 through 3, the

symbol will flash until the iron is fully heated to the next selection, and then

remain constant. If changing to a setting higher than

3, a symbol appears and flashes until the selected

temperature is reached, then remains constant.

5. If the Steam On/Off button is pressed at any time

during use, the iron stops producing steam and the

steam symbol disappears from the LCD display.

IRONING WITH STEAM

When using steam, be sure the iron is filled with water before you begin to

iron.

ALL-TEMP STEAM® System

ALL-TEMP STEAM® utilizes Smart Steam® technology and enables you to

utilize steam on all fabrics and temperature settings — even LOW.

Smart Steam® Technology

The Smart Steam® system automatically generates the right amount of

steam for the fabric type selected. Once you select the temperature, the

Smart Steam® technology detects the set temperature and adjusts the steam

power accordingly.

Suggestions for each setting:

• Acrylic: scarves, blouses, knits – iron on the wrong side

• Nylon: lingerie, robes, sleepwear, raincoats – iron on the wrong side

• Polyester: knits, dresses, blouses, skirts, travel wear - iron on the wrong side

• Blends: shirts, blouses, knits, uniforms, bed and table linens

• Wool: trousers, slacks, jackets, silk scarves and blouses

• Cotton: 100% cotton blouses and shirts, table linens

• Linen: slacks, summer wear, jackets, blouses

Press the Steam On/Off button to turn on the steam func-

tion. The Steam symbol on the LCD display flashes during

heat-up, and then appears constant when the steam

function is ready (I).

SURGE-OF-STEAM

1. Use to remove stubborn creases.

2. Press the surge-of-steam button to generate a burst

of steam (J). For best results, allow at least 5 seconds

between bursts.

USING THE SPRAY BUTTON

Use to dampen tough wrinkles at any setting.

1. Be sure the iron is filled with water.

2. On first use, pump the Spray button

several times

(K).

IRONING WITHOUT STEAM

1. Ironing without steam can be performed at any setting.

2. It is not necessary to empty the water tank; simply

press the steam button to the OFF position. The

steam symbol(s) will disappear from the LCD

display (L).

3. If desired, empty the water tank following the

directions below and press the steam button

to

turn off the steam.

VERTICAL STEAM

Use for removing wrinkles from hanging garments, curtains and drapes.

1. Be sure water tank is filled to maximum capacity.

2. Hang garment to be steamed on a clothes hanger. Curtains and drapes can

be steamed where they are hung.

3. Press fabric selection button to reach appropriate fabric setting. Allow the

iron to stand for 90 seconds until the Standby

symbol in the bottom right of the LCD display changes

to Ready .

4. Hold the iron close, but not touching the fabric.

5. Using your free hand, pull the fabric tight and pump the

surge-of-steam button as you move the iron over the

fabric (M).

EMPTYING THE WATER TANK (OPTIONAL)

Note: It is not necessary to empty the water tank after

each use.

1. Unplug the iron and let it cool.

2. Open the water-fill cover.

3. To release the water, hold the iron over a sink with the

tip pointing down. Water will empty out of the water-fill

opening (N).

SPECIAL FEATURES

Language Settings

Your iron has a multilingual digital display that lets you

select from English, French and Spanish.

To change the language (O):

1. Press and hold the (-) button for 2 seconds; the digital

display shows EN (for English).

2. Press the (-) button again, the display changes to FR

(for French).

3. Press the (-) button one more time and the digital display changes to ES

(Spanish).

Note: The languages will change in the order listed above.

3-Way Automatic Shutoff

The automatic shutoff feature in your iron works as

follows:

• The iron will shut off after 30 seconds of inactivity if left

on its soleplate or tipped over on its side. If left vertically on its heel rest, it will

shut off after 8 minutes of inactivity (P).

• The unit beeps once and the AUTO OFF symbol

on the LCD display appears to let you know the iron has

stopped heating (Q).

Important: Although the iron has turned off, it is still

hot.

• After a few seconds, the backlight on the LCD display turns off.

• If you pick up the iron, an internal motion detector is activated and the iron

starts heating gain.

Tip: You might have to move the iron or shake it gently.

• The unit beeps once, the digital display light comes on, and the previously set

temperature is displayed again.

Note: Wait for iron to reheat completely before resuming operation.

ANTI DRIP System

0

VERTICAL STEAM

3-WAY AUTO OFF

AUTO CLEAN®

ALL-TEMP STEAM

ANTI DRIP

DIGITAL CONTROLS

The anti-drip system prevents water from spotting at low temperatures.

AUTO CLEAN® System

Note: If the AUTO CLEAN® symbol appears on the LCD display, the unit

needs cleaning. Follow the procedure under AUTO CLEAN® System.

CARE AND CLEANING

This product contains no user-serviceable parts. Refer service to qualified

service personnel.

CLEANING OUTSIDE SURFACES

1. Make sure iron is unplugged and has cooled completely. Wipe the soleplate

and outer surfaces with a soft cloth dampened with water. Add mild

household detergent. Never use abrasives, heavy-duty cleansers, vinegar

or scouring pads that may scratch or discolor the iron.

2. After cleaning, steam iron over an old cloth to remove any residue from the

steam vents.

AUTO CLEAN® SYSTEM

To keep the steam vents free of any buildup, follow these instructions about

once a month.

1. Fill the water tank well below the MAX line. Plug in the iron.

2. Select fabric temperature setting 6 and stand the iron on its heel rest.

3. Wait for the iron to beep and display temperature number with

corresponding fabric.

4. Unplug the iron and hold over a sink with the soleplate facing down.

5. Press and hold the AUTO CLEAN® button. Be careful,

as after several seconds, hot water and steam will

come out of the steam vents (R). Continue to hold the

AUTO CLEAN® button until all the water has emptied. If

necessary, rock iron side-to- side and front-to-back.

6. When finished, release the button, stand the iron on its

heel rest and plug it in. Heat for about 2 minutes to dry out any remaining

water.

STORING YOUR IRON

1. Unplug the iron and allow it to cool.

2. Store vertically on its heel to prevent water leaking from the soleplate.

NEED HELP?

For service, repair or any questions regarding your appliance, call the appro

-

priate 800 number on cover of this book. Please DO NOT return the product to

the place of purchase. Also, please DO NOT mail product back to manufac-

turer, nor bring it to a service center. You may also want to consult the website

listed on the cover of this manual.

Two-Year Limited Warranty

(Applies only in the United States and Canada)

What does it cover?

• Anydefectinmaterialorworkmanshipprovided;however,Applica’sliability

will not exceed the purchase price of product.

For how long?

• Twoyearsfromthedateoforiginalpurchasewithproofofsuchpurchase.

What will we do to help you?

• Provideyouwithareasonablysimilarreplacementproductthatiseither

new or factory refurbished.

How do you get service?

• Saveyourreceiptasproofofdateofsale.

• Visittheonlineservicewebsiteatwww.prodprotect.com/applica,orcall

toll-free 1-800-231-9786, for general warranty service.

• Ifyouneedpartsoraccessories,pleasecall1-800-738-0245.

What does your warranty not cover?

• Damagefromcommercialuse

• Damagefrommisuse,abuseorneglect

• Productsthathavebeenmodiedinanyway

• Productsusedorservicedoutsidethecountryofpurchase

• Glasspartsandotheraccessoryitemsthatarepackedwiththeunit

• Shippingandhandlingcostsassociatedwiththereplacementoftheunit

• Consequentialorincidentaldamages(Pleasenote,however,thatsome

states do not allow the exclusion or limitation of consequential or incidental

damages, so this limitation may not apply to you.)

How does state law relate to this warranty?

• Thiswarrantygivesyouspecificlegalrights.Youmayalsohaveother

rights that vary from state to state or province to province.

Por favor lea este instructivo antes de usar el producto.

INSTRUCCIONES

IMPORTANTES DE SEGURIDAD

Cuando se utilizan aparatos eléctricos, siempre se debe respetar

ciertas medidas de seguridad a fin de reducir el riesgo de un

incendio, un choque eléctrico y (o) lesiones a las personas,

incluyendo las siguientes:

•LEA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR EL

PRODUCTO.

•Utilice la plancha solamente con el fin previsto.

•A fin de evitar el riesgo de un choque eléctrico, no sumerja la

plancha en agua ni en ningún otro líquido.

•Siempre ajuste la plancha a la posición de apagado (Off) antes

de conectarla o desconectarla de la toma de corriente. Nunca tire

del cable para desconectar el aparato; sujete el enchufe y hale

con cuidado.

•No permita que el cable entre en contacto con las superficies

calientes. Espere que la plancha se enfríe bien antes de

guardarla. Enrolle el cable holgadamente alrededor de la plancha.

•Siempre desconecte la plancha cuando no esté en uso y cuando

llene o vacíe el tanque de agua.

•No utilice la plancha si el cable o el enchufe presentan algún

desperfecto, si la ha dejado caer o dañado. Para evitar el riesgo

de un choque eléctrico, no desarme la plancha. Acuda a una

persona de servicio calificada. El reensamblaje incorrecto de la

plancha puede ocasionar el riesgo de un choque eléctrico.

•Se requiere supervisar de cerca todo aparato eléctrico al ser

utilizado por o en la presencia de los niños. Nunca descuide la

plancha mientras permanece enchufada ni sobre la tabla de

planchar.

•Pueden ocurrir quemaduras si se tocan las partes metálicas, el

agua caliente, o el vapor. Tome precaución al invertir una plancha

de vapor ya que puede haber agua caliente dentro del tanque.

Evite los movimientos bruscos para no derramar agua caliente.

•La plancha debe usarse o colocarse en una superficie plana y

firme.

- Cuando se coloca la plancha sobre el talón de descanso,

asegúrese de que la superficie sea plana y firme.

- La plancha no se debe usar si se ha caido, si se ha dañado o si

está goteando.

INSTRUCCIONES ESPECIALES

•Para evitar una sobrecarga eléctrica, no utilice ningún otro

aparato de alto consumo de corriente en el mismo circuito.

•Para evitar sobrecargas, no opere ningún otro aparato de alto

consumo de corriente en el mismo circuito. Si el uso de un cable

de extensión es absolutamente necesario, se deberá utilizar uno

de 15 amperios y 120 voltios o uno de 7 amperios y 220 voltios.

Los cables de menor amperaje se pueden sobrecalentar. Se debe

tener cuidado de acomodar el cable de manera que nadie lo hale

ni se tropiece.

CONSERVE ESTAS

INSTRUCCIONES.

Este aparato eléctrico es para uso doméstico

solamente.

ENCHUFE POLARIZADO (MODELOS 120V SOLAMENTE)

Este aparato cuenta con un enchufe polarizado (un contacto es más

ancho que el otro). A fin de reducir el riesgo de un choque eléctrico,

este enchufe encaja en un tomacorriente polarizada en un solo

sentido. Si el enchufe no entra en el tomacorriente, inviértalo y si aun

así no encaja, consulte con un electricista. Por favor no trate de alterar

esta medida de seguridad.

TORNILLO DE SEGURIDAD

Advertencia: Este aparato cuenta con un tornillo de seguridad para

evitar la remoción de la cubierta exterior del mismo. A fin de reducir el

riesgo de incendio o de choque eléctrico, por favor no trate de remover

la cubierta exterior. Este producto no contiene piezas reparables por

el consumidor. Toda reparación se debe llevar a cabo solamente por

personal de servicio autorizado.

Nota:

Si el cordón de alimentación esta dañado, en América Latina

debe sustituirse por personal calificado o por el centro de servicio

autorizado.

COMO USAR

Este aparato es para uso doméstico solamente.

PASOS PRELIMINARES

• Despegue todo rótulo, calcomanía o etiqueta adherida al cuerpo, cable o suela

de la plancha.

• Por favor, visite www.prodprotect.com/applica para registrar su garantía.

• Retire y conserve toda literatura.

• Si va a planchar en seco, coloque el aparato verticalmente sobre una tabla de

planchar estable.

• Desenrolle el cable y enchúfelo a una toma de corriente normal.

Importante: Para mejores resultados, deje reposar la plancha por 90

segundos hasta que el icono “en espera”

en la esquina inferior

derecha de la pantalla VCL cambie a “listo” .

COMO LLENAR EL TANQUE DE AGUA

1. Abra la tapa del orificio de llenado según la ilustración

(A).

2. Incline la plancha y con una taza de medir limpia,

vierta agua en el orificio hasta alcanzar la marca de

llenado MAX en el costado del tanque (B). No exceda

el nivel de llenado.

Nota: El tanque de esta plancha se puede llenar con agua corriente de la

llave; si el agua de la región es demasiado dura o blanda, se puede usar agua

destilada. No use agua procesada por un sistema doméstico de ablan-

damiento de agua.

3. Cierre la tapa del orificio de llenado.

Nota: Si tiene que agregar agua al tanque durante el

planchado, desconecte la plancha y siga los pasos

citados anteriormente.

4. Enchufe la plancha a una toma de corriente.

• El aparato produce un sonido.

• LapantallaVCLseiluminaydespuésseapaga.

• Elsímbolo,“enespera”permaneceenlapantallaVCL

(C).

5. Para encender la plancha, presione el botón del

control de temperatura (+), a la izquierda de la

pantallaVCL(D).

• El aparato produce un sonido.

• LapantallaVCLseilumina.

• LaplanchaseempiezaacalentarylapantallaVCL

exhibe la temperatura más baja.

COMO AJUSTAR LA TEMPERATURA SEGÚN EL

TEJIDO

1. Lea las etiquetas de las prendas para determinar el

tipo de tejido a planchar.

Consejo:

Si desconoce la fibra de cierto tejido, ensaye primero sobre una

superficie pequeña y planche una costura o ruedo interior.

2. Una vez que determine el tipo de tejido, presione los

botones para la selección de tejido (+) y (-) situados a

unoyotroladodelapantallaVCLyelijaeltipodetejido

apropiado (E).LapantallaVCLseiluminayeltipode

tejido aparece en la parte superior, con el número corre-

spondiente debajo, hacia la izquierda. También aparece

una flecha intermitentemente mientras la plancha se está calentando. La

plancha produce

un sonido cuando alcanza la temperatura programada y el

símbolo “en espera”

cambia a “listo” y la flecha desaparece.

3. Siempre que uno ajusta el nivel de temperatura, las flechas

▲

o

▼

aparecennuevamenteenlapantallaVCL,indicandoquelaplanchaseestá

calentando o enfriando según la temperatura programada.

Importante: Siempre coloque la plancha sobre el talón de descanso

cuando esté encendida pero no en uso.

SELECCIÓN DE VAPOR

A

B

C

D

E

F

G

H

I

J

K

ACRYL

1

ACRYL

1

L

M

N

O

30 SECONDS

8 MINUTES

P

30 SECONDS

8 MINUTES

Q

R

A

B

C

D

E

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Black and Decker D6000 Strijkijzer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Black and Decker. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Black and Decker D6000 Strijkijzer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Black and Decker Strijkijzers
Meer handleidingen voor Strijkijzers

Veelgestelde vragen over Black and Decker D6000 Strijkijzer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Black and Decker ICR200 Strijkijzer

Handleiding

Black and Decker IR2050 Strijkijzer

Handleiding

Black and Decker IR05XC Strijkijzer

Handleiding

Black and Decker ICR2020 Strijkijzer

Handleiding

Black and Decker D1700 Strijkijzer

Handleiding

Black and Decker IR4500S Strijkijzer

Handleiding

Black and Decker IR07XC Strijkijzer

Handleiding

Black and Decker ICR07X Strijkijzer

Gerelateerde categorieën