Handleiding Black and Decker KFBCD001 Schroef-boormachine

Handleiding

● When disposing of batteries, follow the instructions given

in the section “Protecting the environment”.

● Do not damage/deform the battery pack either by puncture

or impact, as this may create a risk of injury and re.

● Do not charge damaged batteries.

● Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries carefully wipe the

liquid off using a cloth. Avoid skin contact.

● In case of skin or eye contact, follow the instructions

below.

@

Warning! The battery uid may cause personal

injury or damage to property. In case of skin contact,

immediately rinse with water. If redness, pain or

irritation occurs seek medical attention. In case of

eye contact, rinse immediately with clean water and

seek medical attention.

Chargers

Your charger has been designed for a specic voltage. Always

check that the mains voltage corresponds to the voltage on

the rating plate.

@

Warning! Never attempt to replace the charger unit

with a regular mains plug.

● Use your charger only to charge the battery in the tool with

which it was supplied. Other batteries could burst, causing

personal injury and damage.

● Never attempt to charge non-rechargeable batteries.

● If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Service Centre in order to

avoid a hazard.

● Have defective cords replaced immediately.

● Do not expose the charger to water.

● Do not open the charger.

● Do not probe the charger.

● The appliance/tool/battery must be placed in a well

ventilated area when charging.

$

The charger is intended for indoor use only.

Electrical safety

#

This charger is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on the

rating plate.

● If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Forward/reverse slider

3. Torque adjustment collar

4. Keyless chuck

5. LED work light

6. Battery

7. Battery release button

Assembly

Use

@

Warning! Let the tool work at its own pace. Do not

overload.

Charging the battery (g. A, B)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

@

Warning! Do not charge the battery at ambient

temperatures below 10 °C or above 40 °C.

Recommended charging temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the

charger will begin to charge automatically when the cell

temperature warms up or cools down.

● Plug the charger (8) into any standard 230 Volts 50 Hz

electrical outlet.

● Slide the battery pack (6) into the charger as shown in

gure A, B.

The LED (8a) will ash indicating that the battery is being

charged.

The completion of charge is indicated by the LED (8a)

remaining on continuously. The pack is fully charged and may

be used at this time or left on the charger.

@

Warning! re Hazard. When removing the charger

from the battery, be sure to unplug the charger

from the outlet rst, then remove the battery from

the charger.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged battery. The LED

ashes in the pattern indicated on the label. If you see this bad

battery blink pattern, do not continue to charge the battery.

Return it to a service center or a collection site for ecycling.

Hot/cold pack delay

When the charger detects a battery that is excessively hot or

excessively cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life.

The light ashes in the pattern indicated on the label.

7

ENGLISH

(Original instructions)

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Black and Decker KFBCD001 Schroef-boormachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Black and Decker. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Black and Decker KFBCD001 Schroef-boormachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Black and Decker Schroef-boormachines
Meer handleidingen voor Schroef-boormachines

Veelgestelde vragen over Black and Decker KFBCD001 Schroef-boormachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Black and Decker HP122K Schroef-boormachine

Handleiding

Black and Decker BDCIM18 Schroef-boormachine

Handleiding

Black and Decker BDCDD12 Schroef-boormachine

Handleiding

Black and Decker KC2000F Schroef-boormachine

Handleiding

Black and Decker BDHD18 Schroef-boormachine

Handleiding

Black and Decker BDCDMT108 Schroef-boormachine

Handleiding

Black and Decker KC8402 Schroef-boormachine

Handleiding

Black and Decker EGBL144 Schroef-boormachine

Gerelateerde categorieën