Handleiding Bontrager Duotrap S Fietscomputer

Handleiding

•

1

•

2

•

2

•

3

•

1

•

•

3

4

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

-- Consult the dealer or experienced radio / TV technician for help.

NOTES:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES

OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE GRANTEE OF THIS DEVICE

COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.

Pairing: Consult your ANT + or Bluetooth Smart device’s instructions for pairing. Sensor

will need to be activated directly before pairing process.

Sensor Activation: To verify proper magnet install, spin wheel or turn crank more than

two revolutions. Initial sensor activation and magnet alignment will be indicated by the

LEDs flashing up to 10 times.

Please Note: The sensor will stay active for at least 2 minutes although the LEDs no

longer flash.

Bluetooth Smart Connection: Install and activate sensor. Turn on your phone’s

(or other compatible device) Bluetooth capability. Open the desired cycling app and follow

instructions for Bluetooth Smart sensor connection. Please note, Bluetooth Smart devices

do not always appear in your phone’s settings, even when connected. All apps collect,

share, and display speed and cadence information differently.

FCC ID: 04GDUOTRAPS

This device complies with part 15 of the FCC Rules.

Operation is subject to the following conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

This device complies with Industry Canada RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device

must accept any interference, including interference that may cause undesired operation

of the device.

Leprésent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils

radio. Exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)

l’appareil ne doit pas produire de brouillage, et (2) l’utilsateur de l’appareil doit accepter

tout brouillage radioélectrque subi, meme si le brouillage est susceptible d’en

compromettre le fonctionnement.

www.bontrager.com

IC: 7666A-DUOTRAPS

Remove the pedal and

install cadence magnet on

nondrive side crank arm

with thick side nearer the

chainstay. Use cadence

magnet band that gives

the best fit.

For carbon bikes, place

magnet 135mm or

145mm from the center

of the bottom bracket to

the center of the magnet.

Hint: If the magnet is aligned

but the LED does not

illuminate, place a cadence

band shim underneath the

appropriate magnet.

Verify magnet is aligned with

sensor by illumination of

green cadence sensor LED

as crank is turned. LED will

illuminate for the first 10

revolutions. Align magnet

with tech mark on alloy

bike’s chain stay.

145mm

135mm

SPEED MAGNET INSTALLATION (CARBON AND ALLOY BIKES)

CADENCE MAGNET INSTALLATION (CARBON AND ALLOY BIKES)

PAIRING AND SENSOR ACTIVATION

Speed magnet (carbon

bikes) Snap magnet onto

inside/trailing edge non-drive

side spoke. Some carbon

frame/wheel combinations

may require magnet to be

flipped so the thin side faces

sensor.

Speed magnet (alloy bikes)

Tighten wheel magnet on

spoke for alloy bikes

Align speed magnet with

tech mark on DuoTrap S.

Verify sensor is aligned with

magnet by illumination of red

speed sensor LED as wheel

is rotated. LED will illuminate

for the first 10 revolutions.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Bontrager Duotrap S Fietscomputer. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Bontrager. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Bontrager Duotrap S Fietscomputer in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Bontrager Fietscomputers
Meer handleidingen voor Fietscomputers

Veelgestelde vragen over Bontrager Duotrap S Fietscomputer

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Bontrager Trip 1 Fietscomputer

Handleiding

Bontrager Trip 4W Fietscomputer

Handleiding

Bontrager Trip 100 Fietscomputer

Handleiding

Bontrager Trip 200 Fietscomputer

Handleiding

Bontrager Duotrap Fietscomputer

Handleiding

Bontrager Trip 300 Fietscomputer

Handleiding

Bontrager GoTime Fietscomputer

Handleiding

Echowell BL 12W Fietscomputer

Gerelateerde categorieën