Handleiding Bosch WAS32760GB Wasmachine

Handleiding

8

Safety instructions

 Read the Instruction manual and Installation instructions and all other information enclosed with the washing

machine and act accordingly.

 Retain the documents for subsequent use.

Risk of electric shock  Never pull the cable to disconnect the mains plug

 Only insert/pull out the mains plug with dry hands.

Danger to life For appliances that have reached the end of their service life:

 Disconnect the mains plug.

 Sever the mains cable and discard along with the plug.

 Destroy the lock on the washing machine door. This will prevent children from

locking themselves in and risking their lives.

Danger of suffocation  Keep packaging, film and packaging parts out of the reach of children.

Risk of poisoning  Keep detergents and care products out of the reach of children.

Risk of explosion  Items of laundry pretreated with cleaning agents containing solvents, e.g. stain

remover/cleaning solvent may cause an explosion after being loaded into the

washing machine.

Rinse items of laundry thoroughly by hand beforehand.

Risk of injury  The washing machine door can become very hot.

 Be careful when emptying hot detergent solution.

 Do not climb onto the washing machine.

 Do not lean on the open washing machine door.

 Do not reach into the drum if it is still rotating.

Consumption values

Programme Load Current*** Water***

Programme

duration***

L Cottons 30 °C* 9 kg 0.38 kWh 61 l 2A h

L Cottons 40 °C* 9 kg 1,05 kWh 60 l 2B h

L Cottons 60 °C* 9 kg 1.23 kWh 60 l 2B h

L Cottons 90 °C 9 kg 2.3 kWh 72 l 2A h

/ Mixed Load 40 °C*

3.5 kg 0.47 kWh 35 l 1 h

I Easy-Care 40 °C* 4 kg 0.69 kWh 46 l 1B h

 Delicate/Silk 30 °C 2 kg 0.14 kWh 33 l B h

/c: Wool 30 °C 2 kg 0.16 kWh 40 l B h

* Programme setting for test according to currently valid European standard 60456.

Information about comparability tests: To test the test programmes, wash indicated load size at

maximum selectable spin speed.

Programme Additional function Load

Annual energy

consumption

Annual water

consumption

L Cottons 40/60 °C j EcoPerfect** 9/4,5 kg 196 kWh 11300 l

** Programme setting for testing and energy labelling in accordance with EU directive

2010/30/EU with cold water (15 °C).

*** The values may deviate from the stated values depending on water pressure and hardness,

room temperature, type and amount of laundry, detergents used, fluctuations in the

mains voltage and selected additional functions.

9

Important information

Before washing for the first time

Do not put any laundry in the machine. Turn the tap on. Pour into compartment II:

 approx. 1 litre water

 detergent (dosage according to the manufacturer's instructions for light soiling and according to water hardness)

Set programme selector to  Easy-Care 60 °C and press $ Start/Reload. At the end of the programme, turn the

programme selector to Off.

Protecting the laundry and the machine

 When determining the dosage of all washing powders, additives and cleaning agents, you must follow the

manufacturer's instructions.

 Empty pockets.

 Look out for metal items (paperclips, etc.).

 Wash delicates in a laundry bag (tights, curtains, underwired bras).

 Fasten zips, do up any buttons.

 Brush sand out of pockets and collars.

 Remove curtain fittings or place in the laundry bag.

Load laundry

 For optimum spin behaviour, load large and small items of laundry together.

 Individual items may lead to considerable imbalances.

 Take care not to trap items of laundry between the washing machine door and the rubber seal.

Soaking Load laundry of the same colour.

Pour soaking agent/detergent into compartment II in accordance with the manufacturer's instructions. Turn the

programme selector to L Cottons 30 °C and press $ Start/Reload. After approx. 10 minutes, press

$ Start/Reload to stop the programme. Once the required soaking time has elapsed, press $ Start/Reload again

to continue the programme, or select a different programme.

Starching Laundry must not be treated with fabric softener

Starching is possible in all wash programmes if liquid starch is used. Pour starch into the ~ fabric softener

compartment in accordance with the manufacturer's instructions (rinse first if necessary).

Dyeing/bleaching

Dye should only be used in normal household quantities. Salt may damage stainless steel. Always follow the dye

manufacturer's instructions. Do not use the washing machine for bleaching clothes.

Load display

The load sensor detects how heavily the washing machine is loaded. The laundry is not weighed.

Recommended dosage

Based on the selected programme and the detected load, the recommended dosage function provides a

recommendation for the detergent dosage in %. The % figure refers to the recommendation of the detergent

manufacturer.

Load adjust

Independently of the load display, the automatic load sensing function uses additional sensors to adapt the water and

power consumption ideally to each programme, depending on the type of fabric and the load.

10

Insert for liquid detergent model-dependent

Position the insert for dispensing liquid detergent:

 Remove the detergent drawer completely a page 10.

 Slide the insert forwards.

Do not use the insert (slide upwards):

 for gel detergents and washing powder

 for programmes with the  Prewash and end time options.

Care

ʑ

Machine housing, control panel

 Remove detergent residue immediately.

 Wipe with a soft, damp cloth.

 Do not clean with a jet of water.

Cleaning the detergent drawer ...

... if it contains detergent or fabric softener residues.

1. Pull out, press insert down, remove drawer completely.

2. To remove the insert: press the insert upwards from below with your finger.

3. Clean the detergent dispenser tray and insert with water and a brush and

dry it.

4. Fit the insert and engage (connect the cylinder to the guide pin).

5. Push in the detergent drawer.

Leave the detergent drawer open so that any residual water can evaporate.

ʑ

Drum

Use chlorine-free cleaning agent, not steel wool.

ʑ

Descaling No laundry in the machine.

This should not be necessary if the detergent is measured out correctly. If it does become necessary, however, proceed

according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or

from our after-sales service (page 13).

Information on the display panel depending on model

Door open? Close the washing machine door properly; laundry may be caught.

Tap closed? Open the tap completely, supply hose kinked or trapped; Clean the filter a page 11,

water pressure too low.

Pump blocked? Detergent solution pump blocked; Clean the detergent solution pump a page 11.

Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon a page 11.

Pause

Top-up not poss.;

Water level too high or

Temperature too high

Not possible to add more laundry.

To continue, press the $ Start/Reload button.

F: 23 Water in the base tub, appliance leaking. Call the after-sales service.

F: 34 Washing machine door cannot be locked. Open the washing machine door and close it so

that you hear it "click"; switch the appliance off and on again; set the programme and

make your settings; start the programme.

Other displays Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears

again, call the after-sales service a page 13.

 Risk of electric shock. Disconnect the mains plug.

 Risk of explosion. No solvents.

11

Information about blockages

Detergent solution pump

Turn the programme selector to Off and disconnect the mains plug.

1. Open and remove the service flap.

2. Take the drainage hose out of the retainer.

Remove the sealing cap, allow the detergent solution to flow out.

Push the sealing cap back on.

3. Unscrew the pump cover carefully (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

solution pump must be able to rotate).

5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the

drainage hose in the holder.

6. Refit the service flap and close it.

To prevent unused detergent from flowing straight into the empty during the next wash:

Pour 1 litre of water into compartment II and start the > Drain programme.

Drainage hose at the siphon

Turn the programme selector to Off and disconnect the mains plug.

1. Loosen the hose clamp, remove the drainage hose carefully (residual water).

2. Clean the drainage hose and siphon connecting piece.

3. Reattach the drainage hose and secure the connection with the hose clamp.

Filter in the water supply

Risk of electric shock

Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).

Reduce the water pressure in the supply hose:

1. Turn off the tap.

2. Select any programme (except  Spin/ > Drain).

3. Press $ Start/Reload. Let the programme run for approximately 40 seconds.

4. Turn the programme selector to Off. Disconnect the mains plug.

Clean the filter:

5. Disconnect the hose from the tap.

Clean the filter with a small brush.

and/or for Standard and Aqua-Secure models:

Remove the hose from the rear of the appliance.

Remove the filter with pliers and clean.

6. Connect the hose and check for leaks.

 Risk of scalding.

Allow the detergent solution to cool down.

 Turn off the tap.

12

What to do if...

ʑ

...Water is escaping:  Attach/replace the drainage hose correctly.

 Tighten the screw connection of the supply hose.

ʑ

...No water is entering the drum:  $ Start/Reload not selected?

 Tap not turned on?

 Filter blocked? Clean the filter a page 11.

 Supply hose kinked or trapped?

ʑ

...Washing machine door cannot

be opened:

 Safety function active. Programme stopped? a page 4.

  Rinse stop (no final spin) selected? a page 3,4.

 Can be opened by emergency release only? a page 13.

ʑ

...Programme does not start:  $ Start/Reload or end time selected?

 Washing machine door closed?

 Childproof lock active? Deactivate a page 5.

ʑ

...Detergent solution

does not empty.

  Rinse stop (no final spin) selected? a page 3,4.

 Clean the detergent solution pump a page 11.

 Clean the waste pipe and/or drainage hose.

ʑ

...Water not visible in the drum:  Not a fault - water below the visible area.

ʑ

...Spin result not satisfactory.

Laundry wet/too damp:

 Not a fault - the unbalanced-load detection system interrupted spinning, uneven

laundry distribution.

Distribute large and small items of laundry evenly in the drum.

  Easy-iron selected? a page 5.

 Speed selected too low? a page 5.

ʑ

...The programme duration

changes during the washing

cycle:

 Not a fault - the programme sequence is optimised for the relevant washing

process. This can cause changes in the programme duration in the display panel.

ʑ

...Spinning is restarted several

times:

 Not a fault - unbalanced-load detection system is adjusting the imbalance.

ʑ

...Residual water in the ~

compartment for care products:

 Not a fault - the action of the care product is not affected.

 Clean the insert if necessary a page 10.

ʑ

...Odours build up in the washing

machine:

 Run the L Cottons 90 °C programme without laundry. Use standard detergent.

ʑ

...The³3status display lights

up:

Foam may be escaping from the

detergent drawer:

 Too much detergent used?

Mix 1 tablespoon of fabric softener with ½ litre of water and pour into

compartment II (not for outdoor or down fabrics).

 Reduce the detergent dosage for the next wash cycle.

ʑ

...Loud spinning, vibrations and

walking during the spin cycle:

 Are the appliance feet fixed?

Secure appliance feet a Installation instructions.

 Transportation safety devices removed?

Remove transportation safety devices a Installation instructions.

ʑ

...Noises emitted during

spinning and emptying:

 Clean the detergent solution pump a page 11.

ʑ

...Display panel/indicator lamps

do not function during

operation:

 Power cut?

 Circuit breakers tripped or fuses blown? Reset the circuit breakers or change

the fuses.

 Energy saving mode active? a page 1.

 If the fault occurs repeatedly, call the after-sales service.

ʑ

...Programme sequence longer

than usual:

 Not a fault - unbalanced-load detection system is adjusting the imbalance by

repeatedly redistributing the laundry.

 Not a fault - foam detection system active - several rinse cycles are added.

ʑ

...There is detergent residue

on the laundry:

 Occasionally, phosphate-free detergents contain water-insoluble residues.

 Select the Rinse programme or brush out the laundry after washing.

 Use liquid detergent

13

What to do if ...

ʑ

in Reload mode,

$ Start/Reload flashes very

quickly and an audible signal

sounds:

 Water level too high. Close the washing machine door immediately.

 To continue, press the $ Start/Reload button.

If you cannot correct a fault yourself (switching on/off) or a repair is required:

 Turn the programme selector to Off and remove the mains plug from the socket.

 Turn off the tap and call the after-sales service a page 13.

Emergency release e.g. in the event of a power cut

The programme continues when the power supply is restored. However, if the laundry has to be removed, the washing

machine door can be opened as follows:

Risk of scalding

The detergent solution and laundry may be hot. If possible, leave to cool down.

Do not reach into the drum if it is still rotating.

Do not open the washing machine door if water can be seen through the glass.

1. Turn the programme selector to Off and disconnect the mains plug.

2. Empty the detergent solution a page 11.

3. Pull the emergency release downwards with a tool and release.

Washing machine door can then be opened.

After-sales service

ʑ

If you cannot remedy the fault yourself (What to do if ..., a page 12, 13), contact our after-sales service. We will

always find a suitable solution to avoid unnecessary visits by repair personnel.

ʑ

The contact details of your nearest after-sales service can be found here or in the after-sales service directory

(model-dependent).

 GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute.

A call set-up fee of up to 6 pence may apply.)

ʑ

Please give customer service the product number (E-Nr.) and the production number (FD) of the appliance.

Product number Production number

This information can be found:

on the inside of the washing machine door*/opened service

flap* and rear of the appliance.

*model-dependent

ʑ

Trust the manufacturer's competence. Turn to us.

You will thereby ensure that the repairs are performed by trained service personnel equipped with original repair parts.

Washing machine

en Instruction manual

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Bosch WAS32760GB Wasmachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Bosch. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Bosch WAS32760GB Wasmachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Bosch Wasmachines
Meer handleidingen voor Wasmachines

Veelgestelde vragen over Bosch WAS32760GB Wasmachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.