Handleiding Brinsea Octagon 20 ECO Broedmachine

Handleiding

AE21 GB Issue 02

3

Optional Autoturn Cradle:-

2 Base bars

1 Motorised cradle end

1 Plain cradle end

1 Set of four bolts

2.1 Please identify each part and check that they are all present and undamaged. If there are any parts

damaged or missing please contact your retailer or Brinsea Products (at the address at the end of the

document). Damaged appliances shall not be used.

2.2 Check also that the electrical supply matches the machine’s requirements (marked on the technical label

on the inside of the lid of the incubator and on the inside of the blank Autoturn cradle end). The power

cord set must be an appropriately rated and approved cord-set in accordance with the regulations of the

country it is used in.

2.3 To register your new Brinsea product please visit www.brinsea.co.uk and follow the link on the right

hand side of the home page to qualify for your free 2 year guarantee.

2.4 Go to www.Brinsea.co.uk and register as a free member of the Brinsea Email Group to receive the latest

news and information such as advance notice about new products, special offers, exclusive competitions

and much more.

3 Location, Installation and Temperature

3.1 Your incubator will give best results in a room free from wide temperature variations and with generous

ventilation – particularly if several incubators are running at the same time. Ensure that the room

temperature cannot drop on a cold night. Ideally thermostatically control the room at between 20 and

25°C (68 and 77°F). Never allow the room temperature to drop below 15°C (59°F) and ensure that the

incubator cannot be exposed to direct sunlight. Do not use your incubator on the floor.

3.2 If using the Autoturn cradle: Assemble the Autoturn cradle in accordance with the diagram below (Fig. 2)

and place on a flat, level surface (workbench height is ideal). Place the incubator into the Autoturn cradle

as illustrated (Fig. 1). The cabinet is designed to locate onto the lugs at either end of the Autoturn cradle.

Take care to offer the incubator at the angle which matches that of the drive lug to avoid damage to the

mechanism. Ensure full engagement in the slots in the ends of the incubator so that the incubator is level

end to end.

FIG. 2

3.3 If using without the Autoturn cradle place the incubator upright on a flat level surface.

3.4 Remove the lid and place it where it can not be splashed by water. Lift out the egg tray and fill one of the

two water channels (Octagon 20) or two of the four water channels (Octagon 40) with water or 100:1

Brinsea Incubation Disinfectant Solution leaving the top of the liquid 3/4” (20mm) from the top of the

channel. Replace the tray and replace the lid. Slide the ventilation control to the centre of its range.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Brinsea Octagon 20 ECO Broedmachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Brinsea. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Brinsea Octagon 20 ECO Broedmachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Brinsea Broedmachines
Meer handleidingen voor Broedmachines

Beoordeling

Gerelateerde producten

Handleiding

Brinsea Octagon 40 Eco Broedmachine

Handleiding

Brinsea Ovation 28 Advance Broedmachine

Handleiding

Brinsea Ovation 56 Zoologica Broedmachine

Handleiding

Brinsea Maxi II Eco Broedmachine

Handleiding

Brinsea Contaq Z7 Raptor Broedmachine

Handleiding

Brinsea Ova-Easy 380 Broedmachine

Handleiding

Brinsea Ova-Easy 580 Broedmachine

Handleiding

Brinsea Ovation 56 EX Broedmachine

Gerelateerde categorieën