2B3.
ENGLISH
DESCRIPTION
The unit can be found in filtering hoods or in exhaust hoods.
In the Filtering hoods (Fig.1) the air and steam taken up by the unit are purified with charcoal filters and returned
to the environment through the aeration grids on the side of the flue. WARNING: When using filtering hoods, both
charcoal filters and an air deflector (A) must be used. Located in the lower part of the flue, this deflector recycles
the air to the environment.
The charcoal filters are not supplied. In the Exhaust hoods (Fig.2) an exhaust duct conveys the steam and
cooking odors directly outside through the wall/ceiling. Therefore they do not require charcoal filters.
INSTALLATION
To facilitate installation, before starting remove the grease filters:
To remove the metal grid (Fig.3), push the two stops towards the inside of the hood and turn the grid until this can be
removed.
To remove the metal filter/s (Fig.4A or 4B), in line with the handle, push the stop inwards and pull the filter down.
Wall fitting (Fig.5): making use of the appropriate drilling jig (Fig.6), apply the supplied blocks into the wall,
and remember the distance between the hood and the cooktop must be at least 65 cm. Insert two of the supplied
screws so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance
(A). Once the apparatus is hooked, fix it definitively to the wall using the two other screws and the holes made
at its bottom (B). To avoid damage make exclusive use of the holes already prepared on the hood.
Securing the telescopic flue: Basic installation requirements:
– Set the electrical power supply within the space covered by the decorative flue.
– If your unit is installed in an Exhaust hood, prepare the air exhaust hole.
Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches
on the centre of the bracket (Fig.7); using a pen, mark the 2 holes on the wall and then make the holes and fit
the screw anchors provided and proceed to secure the bracket using the 2 screws (provided).
Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock it
to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all power
connections to the hood by means of the power cable. Take 2 assembled flues and place these on the upper
surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws
(Fig.8).
Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower
flue as shown in Figure 9, using the 2 screws. Take 2 assembled flues and place these on the upper surface
of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.8).
Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such
filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:
- if the hood features round charcoal filters (Fig.10), fit the charcoal filter by turning anti-clockwise.
- if the hood features round charcoal filters (Fig.11), remove the charcoal filter by turning it clockwise.
OPERATION
Depending on the model, the unit is equipped with the following controls:
Controls shown in Fig.12: Button A = light switch. Button B = first speed motor ON/OFF switch. Button C =
second speed switch. Button D = third speed switch. E = motor on light.
Controls shown in Fig.13: A = Light switch; position 0: light off; position 1: light on. B = Motor switch; position
0: motor off; position 1-2-3: motor on at speed I, II and III. C = Motor pilot lamp.
Charcoal filter/s: if using the hood in the filtering hood, the charcoal filter/s must be replaced periodically on the
average once every 6 months. To remove the charcoal filters, proceed as follows, remove the charcoal filter by
turning clockwise. If the model purchased has the controls shown in Figure 12/13, the charcoal filters must be
replaced according to use: on the average once every 6 months.
To gain access to the incandescence bulbs, remove the grease filters as described above and remove the
bulbs. Replace with lamps of the same type.
If the model purchased has the halogen lamps need changing, slacken the ring nut in an anticlockwise direction
and remove the bulb itself (Fig.14). Replace with a bulb of the same type. CAUTION: Do not handle glass bulb
with bare hands.
The motor used in this hood features a safety device (thermal cutout) that responds to temperature
changes For accidental reasons or due to installation faults, this device could engage and automatically
shut off the motor, thereby preventing serious damage to the equipment. In such cases, after allowing
the motor to cool down, the hood can be switched on again; the cause of the fault will nonetheless have
to be remedied, ensuring installation has been correctly made and that all the instructions in the Information
sheet have been complied with.
Praat mee over dit product
Laat hier weten wat jij vindt van de Candy CCH 915 X Afzuigkap. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.