Handleiding Casio Baby-G BGD-140-1AER Horloge

Handleiding

Operation Guide 3277/3404

E-19

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

When the progress beeper is turned off, the countdown end beeper sounds for x

about 10 seconds, or until you press any button to stop it.

When the progress beeper is turned on, the countdown end beeper sounds for x

about one second.

Progress Beeper

When the progress beeper is turned on, the watch uses beeps to signal countdown

progress as described below.

Starting from fi ve minutes before the end of the countdown, the watch emits four x

short beeps at the top of each countdown minute.

30 seconds before the end of the countdown, the watch emits four short beeps. x

The watch emits a short beep for each of the last 10 seconds of the countdown. x

If the countdown start time is six minutes or greater, the watch emits a short beep x

for each second of the fi nal 10 seconds before the fi ve-minute point is reached. Four

short beeps are emitted to signal when the fi ve-minute point is reached.

E-18

Auto-repeat

When auto-repeat is turned on, the countdown restarts automatically from the

countdown start time when it reaches zero.

When auto-repeat is turned off, the countdown stops when it reaches zero and the

display shows the original countdown start time.

Pressing x D while an auto-repeat countdown is in progress pauses the current

countdown. You can resume the auto-repeat countdown by pressing D, or you can

press A to reset to the countdown time starting value.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed

about the countdown status without looking at the display. The following describes the

types of beeper operations the watch performs during a countdown.

E-17

Countdown Timer

The countdown timer can be set within a range of

one minute to 24 hours. An alarm sounds when the

countdown reaches zero. The countdown timer also

has an auto-repeat feature and a progress beeper that

signals the progress of the countdown.

All of the operations in this section are performed in the x

Countdown Timer Mode, which you enter by pressing

C (page E-5).

Confi guring the Countdown Timer

The following are the settings you should confi gure

before actually using the countdown timer.

Countdown start time; Auto-repeat on/off; Progress

beeper on/off

See “To confi gure the countdown timer” (page E-20) for x

information about setting up the timer.

Hours

Minutes

Seconds

E-16

About Auto-Start

With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation

starts automatically when the countdown reaches zero.

During the fi nal three seconds of the countdown, a beeper sounds with each second.

To use Auto-Start

While the stopwatch screen is showing all zeros in the 1.

Stopwatch Mode, press A.

This displays a 5-second countdown screen. x

To return to the all zeros screen, press x A again.

Press 2. D to start the countdown.

When the countdown reaches zero, a tone sounds and a x

stopwatch timing operation starts automatically.

Pressing x D while the Auto-Start countdown is in

progress starts the stopwatch immediately.

E-15

To measure times with the stopwatch

Elapsed time

D D D D A

Start Stop Re-start Stop Clear

Split time

D A A D A

Start Split

(SPL displayed)

Split release Stop Clear

Two Finishes

D A D A A

Start Split

First runner

fi nishes.

Display time of

fi rst runner.

Stop

Second runner

fi nishes.

Split release

Display time of

second runner.

Clear

E-14

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two fi nishes. It also includes Auto-Start.

The display range of the stopwatch is 23 hours, x

59 minutes, 59.99 seconds.

The stopwatch continues to run, restarting from zero after x

it reaches its limit, until you stop it.

The stopwatch measurement operation continues even if x

you exit the Stopwatch Mode.

Exiting the Stopwatch Mode while a split time is frozen x

on the display clears the split time and returns to elapsed

time measurement.

All of the operations in this section are performed in the x

Stopwatch Mode, which you enter by pressing C (page

E-5).

1/100 second

Hours

Minutes

Seconds

E-13

To toggle a city code time between Standard Time and Daylight Saving Time

In the World Time Mode, use 1. D to display the city code

whose Standard Time/Daylight Saving Time setting you

want to change.

Hold down 2. A for about one second to toggle Daylight

Saving Time (DST displayed) and Standard Time (DST

not displayed).

The x DST indicator is on the display whenever you display

a city code for which Daylight Saving Time is turned on.

Note that the DST/Standard Time setting affects only x

the currently displayed city code. Other city codes are

not affected.

DST indicator

E-12

World Time

World Time shows the current time in 48 cities (29 time

zones) around the world.

All of the operations in this section are performed in x

the World Time Mode, which you enter by pressing C

(page E-4).

To view the time for another city code

In the World Time Mode, press D to scroll eastwardly

through city codes.

For full information about city codes, see the “City Code x

Table” at the back of this manual.

If the current time for a city is wrong, check your x

Timekeeping Mode time and the UTC offset settings

and make necessary changes.

City code

Current time and date in

the zone of the selected

city code

E-11

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and

24-hour timekeeping.

With the 12-hour format, the x P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without x

any indicator.

The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is x

applied in all other modes.

E-10

To toggle the Timekeeping Mode time between DST and Standard Time

In the Timekeeping Mode, hold down 1. A until the

seconds start to fl ash, which indicates the setting

screen.

Press 2. C to display the DST setting screen.

Press 3. D to toggle between Daylight Saving Time (

displayed) and Standard Time (

displayed).

Press 4. A to exit the setting screen.

The x DST indicator appears on the display to indicate that

Daylight Saving Time is turned on.

DST indicator

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Casio Baby-G BGD-140-1AER Horloge. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Casio. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Casio Baby-G BGD-140-1AER Horloge in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Casio Horloges
Meer handleidingen voor Horloges

Veelgestelde vragen over Casio Baby-G BGD-140-1AER Horloge

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Casio Collection MWD-110H-1AVEF Horloge

Handleiding

Casio G-Shock GA-B2100-2AER Horloge

Handleiding

Casio G-Shock GBX-100TT-8ER Horloge

Handleiding

Casio Collection LTP-1302PRG-3AVEF Horloge

Handleiding

Casio Collection W-800H-2AVES Horloge

Handleiding

Casio G-Shock GST-B500BD-1A9ER Horloge

Handleiding

Casio Pro Trek PRW-35-1AER Horloge

Handleiding

Casio Collection WS-1600H-1AVEF Horloge

Gerelateerde categorieën