Handleiding Casio Collection LWS-1000H-1AVEF Horloge

Handleiding

Operation Guide 3469

E-29

To configure countdown start time and auto-repeat settings

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down

A

until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-28) to display it.

2. Press

C

to move the flashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Hours)

Start Time

(Minutes)

Auto-Repeat

On/Off

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

l

Auto-repeat on indicator

On/Off status

E-28

To use the countdown timer

Press

D

while in the Countdown Timer Mode to start the countdown timer.

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is reset automatically to its starting value after the alarm stops.

• When auto-repeat is turned on, the countdown will restart automatically without

pausing when it reaches zero. The alarm sounds when the countdown reaches

zero.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• Press

D

while a countdown operation is in progress to pause it. Press

D

again to

resume the countdown.

• To stop a countdown operation completely, first pause it (by pressing

D

), and then

press

E

. This returns the countdown time to its starting value.

E-27

Countdown Timer

You can set the countdown timer within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero.

• You also can select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

C

(page E-7).

Seconds

Hours Minutes

Timekeeping

Mode time

Auto-repeat

on indicator

l

l

l

l

l

l

l

l

l

l

E-26

To delete a log

1. In the Recall Mode, display the title screen of the log you want to delete.

2. Hold down

D

and

E

until stops flashing on the display.

• This deletes the log and all the records inside it.

• Deleting a single log slides all newer logs (ones with higher log numbers) upwards

to fill the empty space. This cause the log numbers of all the newer logs to be

reduced by 1. If there are six logs currently in memory (numbered

01

through

06

)

and you delete log

03

, the numbers of logs that previously were numbered

04

,

05

,

and

06

will change to

03

,

04

, and

05

.

E-25

Press

D

.

Press

E

.

Lap number

Split number

Log number

Log Title Screen

First record Last record

Lap time

Split time

▲

▲

D

E

▲

▲

▲

• Whether you will be able to view lap time records or split time records will depend

on the screen you selected in step 2, above.

E-24

To recall stopwatch time records

1. In the Stopwatch Mode, check to make sure that the displays reset to all zeros (page

E-16).

• If all zeros are not displayed, reset the stopwatch.

2. Use the

E

button to select either the lap time screen (to view lap time records) or

the split time screen (to view split time records) (pages E-16 and E-18).

• To convert a lap time saved in the Stopwatch Mode to a split time, select the split

time screen.

3. Press the

C

button to enter the Recall Mode.

4. Use the

A

button to scroll through the log title screens from the newest to the

oldest until the title screen of the log whose records you want to view is displayed.

5. Use

D

(forward) and

E

(back) to scroll through records in lap number sequence.

E-23

Recall Mode

Use the Recall Mode to recall and delete logs and records

you stored in the Stopwatch Mode. You can use the

Recall Mode to view both lap and split time records.

• When you enter the Recall Mode, the newest log

recorded in the Stopwatch Mode will appear first. If

there are no logs in memory,

appears on the

display.

• You can use the Recall Mode to check memory data

even while a stopwatch elapsed time measurement

operation is in progress. However, the time data that is

currently being measured will not appear in the Recall

Mode.

• You can convert a lap time saved in the Stopwatch

Mode to a split time (page E-24).

Day of week

Month – Day

Log number

Log Title Screen

E-22

How stopwatch data is stored

The following table shows how stopwatch data is stored when you perform stopwatch

button operations.

Stopwatch Button Operation Data Storage Description

From all-zeros, press

D

to

start.

Creates a new log. Stores the date the button was pressed,

and the new log number.

Press

E

to display lap/split

time.

Creates a new record with each button operation. Stores

the lap and split times and total elapsed time at each point

the button is pressed.

Press

D

to stop elapsed time

measurement and then press

E

to reset.

Resets the elapsed time to all zeros without recording data.

• See “Recall Mode” (page E-23) for details on how to recall time records from memory.

E-21

Memory Management

A new log is created each time you press

D

in the Stopwatch Mode to start a new

elapsed time measurement operation. A log contains a log title screen, and records of

all the lap or split times you record during the current elapsed time measurement

operation.

• The capacity of the watch’s memory is 60 records.

• If you are adding records to a log when there are multiple logs in memory and

watch memory becomes full, adding another record causes the oldest log in

memory and all of its records to be deleted automatically to make room for new

records.

E-20

To time first and second place finishes

1. When the stopwatch display shows all zeros, press

E

to display the split time

screen (indicated by

).

2. Press

D

to start a time measurement.

3. Press

E

when the first finisher crosses the finish line.

• This freezes the time of the first finisher in the lower part of the display for about

eight seconds. After that, the display returns to elapsed time measurement.

4. Press

D

when the second finisher crosses the finish line.

• The second finisher’s time will appear in the lower display.

• The difference between the first finisher’s and the second finisher’s time will

appear in the upper display.

5. Press

E

to clear the stopwatch to all zeros.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Casio Collection LWS-1000H-1AVEF Horloge. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Casio. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Casio Collection LWS-1000H-1AVEF Horloge in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Casio Horloges
Meer handleidingen voor Horloges

Veelgestelde vragen over Casio Collection LWS-1000H-1AVEF Horloge

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Casio G-Shock DW-6900TD-4ER Horloge

Handleiding

Casio G-Shock DW-5900TD-9ER Horloge

Handleiding

Casio Sheen SHE-3517L-1AUEF Horloge

Handleiding

Casio Edifice EQB-2000DB-1AER Horloge

Handleiding

Casio Baby-G BGD-565US-7ER Horloge

Handleiding

Casio Pro Trek PRG-340-1ER Horloge

Handleiding

Casio Sheen SHE-4539CM-4AUER Horloge

Handleiding

Casio Edifice EFR-574D-1AVUEF Horloge

Gerelateerde categorieën