Handleiding Casio G-Shock AW-591-4AER Horloge

Handleiding

2

Operation Guide 4778

DST indicator

To toggle the Timekeeping Mode digital time between DST and Standard Time

1. In the Timekeeping Mode, hold down A until the seconds

start to flash, which indicates the setting screen.

2. Press C once to display the DST setting screen.

3. Press D to toggle between Daylight Saving Time (

ON

displayed) and Standard Time (

OF

displayed).

4. Press A to exit the setting screen.

• The DST indicator appears on the Timekeeping, Alarm,

and Hand Setting Mode to indicate that Daylight Saving

Time is turned on.

Setting the Analog Time

Perform the procedure below when the time indicated by the analog hands does not

match the time of the digital display.

To adjust the analog time

1. In the Timekeeping Mode, press C five times to enter

the Hand Setting Mode.

2. Hold down A until the current digital time starts to

flash, which indicates the analog setting screen.

3. Press D to advance the analog time setting by

20 seconds.

• Holding down D advances the analog time setting at

high speed.

• If you need to advance the analog time setting a long way, hold down D until the

time starts advancing at high speed, and then press B. This locks the high-

speed hand movement, so you can release the two buttons. High-speed hand

movement continues until you press any button. It will also stop automatically

after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,

or countdown beeper) starts to sound.

4. Press A to exit the setting screen.

• The watch will automatically adjust the minute hand slightly to match its internal

second count when you exit the setting screen.

• To return to the Timekeeping Mode, press C.

City code

Current time for the

selected city code

World Time

World Time digitally displays the current time in 27 cities

(29 time zones) around the world.

• All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

To view the time in another city

In the World Time Mode, press D to scroll eastwardly

through city codes.

• For full information about city codes, see the “City Code

Table”.

• If the current time shown for a city is wrong, it probably

means there is a problem with your Timekeeping Mode

time and/or Home City code settings. Go to the

Timekeeping Mode and make the necessary

adjustments.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

whose Standard Time/Daylight Saving Time setting you

want to change.

2. Hold down A for about two seconds to toggle between

Daylight Saving Time (DST indicator displayed) and

Standard Time (DST indicator not displayed).

• The DST indicator is on the display whenever you

display a city code for which Daylight Saving Time is

turned on.

• Note that the DST/Standard Time setting affects only the

currently displayed city code. Other city codes are not

affected.

• Note that you cannot switch between Standard Time

and Daylight Saving Time while

GMT is selected as the

city code.

SecondsSeconds

Minutes

DST indicator

Countdown Timer

The countdown timer can be set within a range of one

minute to 60 minutes. An alarm sounds when the

countdown reaches zero. The countdown timer also has

an auto-repeat feature and a progress beeper that signals

the progress of the countdown.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

C.

Configuring the Countdown Timer

The following are the settings you should configure before

actually using the countdown timer.

Countdown start time; Auto-repeat on/off; Progress

beeper on/off

• See “To configure the countdown timer” for information

about setting up the timer.

Auto-repeat

When auto-repeat is turned on, the countdown automatically restarts from the

countdown start time when it reaches zero. If left running, the countdown is repeated

a total of eight times, after which it stops automatically.

When auto-repeat is turned off, the countdown stops when it reaches zero and the

display shows the original countdown start time.

• Pressing D while an auto-repeat countdown is in progress pauses the current

countdown. You can resume the auto-repeat countdown by pressing D, or you can

press A to reset to the countdown time starting value.

Countdown Timer Beeper Operations

The watch beeps at various times during a countdown so you can keep informed

about the countdown status without looking at the display. The following describes the

types of beeper operations the watch performs during a countdown.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

• When the progress beeper is turned off, the countdown end beeper sounds for

about 10 seconds, or until you press any button to stop it.

• When the progress beeper is turned on, the countdown end beeper sounds for

about one second.

Progress Beeper

When the progress beeper is turned on, the watch uses beeps to signal countdown

progress as described below.

• Starting from five minutes before the end of the countdown, the watch emits four

short beeps at the top of each countdown minute.

• 30 seconds before the end of the countdown, the watch emits four short beeps.

• The watch emits a short beep for each of the last 10 seconds of the countdown.

• If the countdown start time is six minutes or greater, the watch emits a short beep for

each second of the final 10 seconds before the five-minute point is reached. Four

short beeps are emitted to signal when the five-minute point is reached.

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Start Time

Auto-repeat

Progress Beeper

3. When the setting you want to change is flashing, use

B and D to change it as described below.

Setting

Start Time

Auto-repeat

Progress Beeper

Screen Button Operation

Use D (+) and B (–) to change the setting.

• You can set a start time in the range of 1 to 60 minutes in

1-minute increments.

Press D to toggle auto-repeat on ( displayed) and off

( displayed).

Press D to toggle the progress beeper on (ON) and off

(OF).

4. Press A to exit the setting screen.

• You can also perform steps 1 and 2 of the above procedure whenever you need to

view the current auto-repeat and progress beeper settings.

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

• The countdown timer operation continues even if you

exit the Countdown Timer Mode.

• Press D while a countdown operation is in progress to

pause it. Press D again to resume the countdown.

• To completely stop a countdown operation, first pause it

(by pressing D), and then press A. This returns the

countdown time to its starting value.

Seconds

Minutes

1/100 second

SPL indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

• The display range of the stopwatch is 59 minutes,

59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

To measure times with the stopwatch

Elapsed Time

Start

Stop Re-start Stop

Clear

Start

Split

(SPL indicator

displayed)

Split release Stop Clear

Start

Split Stop Split release Clear

Split Time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Casio G-Shock AW-591-4AER Horloge. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Casio. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Casio G-Shock AW-591-4AER Horloge in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Casio Horloges
Meer handleidingen voor Horloges

Veelgestelde vragen over Casio G-Shock AW-591-4AER Horloge

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Casio Edifice EFV-C110D-1A3VEF Horloge

Handleiding

Casio Collection W-219HD-1AVEF Horloge

Handleiding

Casio G-Shock GA-110CD-1A3ER Horloge

Handleiding

Casio Edifice EFR-552L-5AVUEF Horloge

Handleiding

Casio G-Shock DW-6900TD-4ER Horloge

Handleiding

Casio G-Shock GA-B2100-1AER Horloge

Handleiding

Casio G-Shock DW-5900TD-9ER Horloge

Handleiding

Casio Edifice ECB-40PB-1AEF Horloge

Gerelateerde categorieën