Handleiding Clarke CTJ 3GLC Krik

Handleiding

Thank you for purchasing this Clarke Long Reach Trolley Jack.

Before attempting to use the unit, please read this instruction booklet thoroughly, and follow

all directions carefully, paying particular attention to the safety precautions. By doing so,

you will ensure the safe operation of the unit, and the safety of yourself and others around

you. You can then look forward to long and reliable service from your CLARKE Trolley Jack.

SAFETY PRECAUTIONS

1. This jack is for lifting ONLY..DO NOT move a load using the jack as a dolley

2. Always inspect the jack before use. Ensure that all parts are in good condition and

operating smoothly, the wheels are sound and that no cracks or distortion is apparent.

If in doubt do not use. Have the parts replaced or consult your CLARKE dealer.

3. Ensure the jack is on a firm solid base, and that there is no likelihood of it slipping when

under load.

4. Ensure the load is taken by the FULL saddle and that the point of lift on the load, is of

sufficient strength to support the full load adequately.

5. Always ensure that the load is stabilised or supported in such a way that it will not shift

during lifting or lowering operations.

6. Always use supports to stabilise the load once lifted. NEVER work on or under a load

unless it is fully and adequately supported. NEVER rely upon the jack to hold the load

in position.

7. Never push a load off the jack.

8. Ensure that all personnel are well clear of a load being raised, or lowered.

9. NEVER exceed the rated load for the jack (see ‘Specifications’).

10. Do not use if an oil leak is apparent...Consult your Clarke dealer.

FITTING THE JACK HANDLE

Remove the bolt, at the rear of the jack handle housing, sufficient for the handle to be

inserted fully, with the Release Valve Operating Lever facing forward (see Fig.1).

Replace the bolt so that it locates in the hole provided in the handle shaft, and tighten fully.

OPERATION

POSITIONING THE JACK

5 and 10 tonne models:

When at rest, the locking mechanism will automatically lock the handle

in one of the three positions. To release the handle, raise the lever and

engage it in the upper slot.

To lock the handle in any particular position, raise the operating lever and

hold it, against spring pressure, in order to disengage the locking

mechanism., Move the handle to the desired position and release the

valve operating lever so that is reasserts to the bottom of the slot. The

locking bar will automatically snap into the locating hole when the

components line up. To release the locking mechanism again, simply lift

the operating lever, and to prevent the locking mechanism from

operating, turn the lever sideways so that it engages in the upper slot.

RAISING AND LOWERING

Ensure the load is chocked and stable and on firm level ground, before manoeuvring the

jack so that the saddle is directly beneath the lifting point.

3 tonne model.

To raise the saddle, allow the lever to remain in the ‘UP’ position and pump the handle.

To lower the load, follow all precautions to ensure that there are no obstacles that could

prevent the load from lowering without hindrance, and that all personnel are well away

from the site, before pushing the lever down, and VERY GENTLY turning it sideways, so that

it enters the lower slot. This will open the release valve and allow the load to drop. The more

you turn the lever, the faster the rate of descent. DO NOT jerk the lever sideways...ALWAYS

lower the load under complete control.

5 and 10 tonne models:

In order to raise the saddle, lift the operating lever and turn sideways so that it engages in

the upper slot, thereby locking the lever in the ‘up’ position. Pumping the handle, or

alternatively the foot pedal, adjacent to the base of the handle, will cause the saddle to

rise.

IMPORTANT:

The foot pedal is used to quickly bring the saddle to the lifting point, NOT to raise a load.

To lower the load, first make one final check to ensure that

there are no obstacles that could prevent the load from

lowering without hindrance, and that all personnel are well

away from the site, before gripping the operating lever

firmly, disengaging it from the upper slot and allowing it to

drop, under control to the bottom of the vertical slot.

VERY GENTLY, turn the lever sideways,

so that it enters the lower slot, thereby

opening the release valve and

allowing the load to drop. The more

you turn the lever, the faster the rate of

descent. DO NOT jerk the lever into

the lower slot...ALWAYS lower the load

under complete control.

For ease of positioning, the jack handle may be locked in three different

positions... vertically...horizontally...and a mid-position. This is achieved as

follows:

3 tonne model:

To lock the handle in place, move it roughly to the desired position, i.e.

vertically, horizontally, or mid-position then push the valve operating lever

downwards as far as possible. Move the handle forwards or backwards

slightly until the locking bar engages in the locating hole at the base of the

handle. This action will be felt at the lever, which may now be moved

sideways so that it engages in the bottom slot, thereby locking the handle

in place. To release the handle, disengage the lever from the bottom slot.

Fig.1

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Clarke CTJ 3GLC Krik. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Clarke. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Clarke CTJ 3GLC Krik in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Clarke Krikken
Meer handleidingen voor Krikken

Beoordeling

Gerelateerde producten

Handleiding

Clarke CTJ 2500QLG Krik

Handleiding

Clarke CTJ 2Q Krik

Handleiding

Clarke CTJ 3000QLB Krik

Handleiding

Clarke CTJ 2250QM Krik

Handleiding

Clarke CTJ 2000G Krik

Handleiding

Clarke CBJ 3B Krik

Handleiding

Clarke CFTJ 500 Krik

Handleiding

Clarke CGLK 1 Krik

Gerelateerde categorieën