Home > Doe-het-zelf & Verbouw > Compressors > Clarke Compressors > Clarke Ranger 60 Compressor

Handleiding Clarke Ranger 60 Compressor

Handleiding voor je Clarke Ranger 60 Compressor nodig? Hieronder kun je de handleiding gratis bekijken en downloaden als PDF in het Nederlands en/of Engels. Dit product heeft 0 veelgestelde vragen, 0 comments en heeft 0 stemmen. Is dit niet de handleiding die je zoekt, neem dan contact met ons op.

Is je product kapot en biedt de handleiding geen oplossing meer? Dan kun je voor reparatie gratis terecht bij Repair Café.

Handleiding

NOTE: Should the motor fail to start immediately, it is probable that the air receiver

is already full of air. Check the tank pressure gauge (see fig. 2). If you release air,

by opening air outlet tap, the motor will start automatically once the cut-in pressure

is reached.

4. Before connecting your airline to the compressor allow it to run with the air

outlet tap completely open for 10 - 15 seconds to permit a good distribution

of the lubricating oil.

5. Close the outlet tap then connect one end of suitable air hose to the

compressor air outlet, and the other and to the equipment to be used.

Set the outlet pressure by adjusting the Output Pressure Regulator. To do this,

turn the knob clockwise to increase pressure, anti-clockwise to decrease.

The Ranger 60 requires that the Regulator Knob be pulled upwards before

it may be turned. Pushing the knob down again holds the pressure setting.

Read the operating pressure on the outlet pressure gauge.

NOTE: For most spraywork do not exceed 50 psi (unless following paint

manufacturers instructions).

For other airline equipment such as air tools, tyre gauges, staple guns, paraffin guns

etc., it may be necessary to set the operating pressure at a higher (or lower) level.

IMPORTANT: Always refer to the accessory manufacturers’ recommendations

for optimum operating pressures for their equipment.

6. With operating pressure set, reopen the air outlet tap.

7. The Pressure Switch, located within the plastic cover beneath the ON/OFF switch,

should not require adjustment. This is an automatic device and has been preset

at the factory to stop the motor when pressure in the receiver reaches its

maximum, and to start it again when the pressure falls to the minimum preset

value. This operation is completely automatic and does not affect the spraying

process in any way. However, should problems develop with the cut-in, cut out

settings, consult your local Clarke international Service Dep’t.

NOTE:

a. If the machine pumps continuously without

cutting out then the compressor is too small

for the application/tool being used, and

damage may result. Consult your local

Clarke international outlet.

b. The motor is protected by a Thermal

Overload so that if the motor overheats

for any reason -the thermal overload

will trip, stopping the motor. To restart,

allow a period for the motor to cool

down (5 min), before pressing the Reset

Button, illustrated in fig. 3.

c. DO NOT exceed the Duty Cycle for the

machine (see Specifications)

Fig. 3

FAULT FINDING

PROBLEM PROBABLE CAUSE REMEDY

The compressor

stops and will not

start again.

Bad connections.

Check the electrical

connections.

Clean and tighten as

necessary.

Blown fuse

Overload cutout

switch has tripped.

Renew/Replace fuse

Switch off and wait 5 minutes

before pressing the reset button.

The compressor

does not reach

the set pressure

and overheats

easily.

Compressor head

gasket blown or valve

broken.

Wait for compressor to cool

down, disassemble the head

and replace any broken

components.

Carefully clean all sealing

surfaces before reassembling.

If in doubt contact Clarke

international

NOTE: It is also possible that

you are using more air than

the compressor is capable of

delivering.

Compressor does

not start.

Air receiver charged

(see also item 1)

Open drain cock to expel air.

Compressor should start again

when pressure reduces to

approx 95 psi.

Air leaking from

the pressure switch

valve when the

compressor is not

running.

Faulty non-return

valve.

First drain the receiver

completely of air. Remove the

valve end plug, carefully clean

the valve seat and the gasket

and reassemble. See Fig 8.

Air pressure from

the regulator will

not adjust.

Replace RegulatorThe diaphragm within

the regulator body is

broken.

The compressor is

very noisy and

makes a metallic

knocking sound.

Return the machine to Clarke

international.

Compressor dam-

aged and needs

overhaul.

Beoordeling

Laat ons weten wat je van de Clarke Ranger 60 Compressor vindt door een beoordeling achter te laten. Wil je je ervaringen met dit product delen of een vraag stellen? Laat dan een bericht achter onderaan de pagina.

Bent u tevreden over de Clarke Ranger 60 Compressor?
Ja Nee

Beoordeel dit product als eerste

0 stemmen

Praat mee over dit product

Laat hier weten wat jij vindt van de Clarke Ranger 60 Compressor. Als je een vraag hebt, lees dan eerst zorgvuldig de handleiding door. Een handleiding aanvragen kan via ons contactformulier.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Clarke Ranger 60 Compressor. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Clarke. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Clarke Ranger 60 Compressor in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.