Handleiding DeWalt D28113 Haakse slijpmachine

Handleiding

3

• Avoid bouncing the wheel or giving it rough treatment. If this occurs, stop the

tool and inspect the wheel for cracks or flaws.

• Direct sparks away from operator, bystanders or flammable materials.

Sparks may be produced while cutting and/or grinding. Sparks may cause

burns or start fires.

• Always use side handle. Tighten the handle securely. The side handle should

always be used to maintain control of the tool at all times.

• Never cut into area that may contain electrical wiring or piping. Serious

injury may result.

• Clean out your tool often, especially after heavy use. Dust and grit containing

metal particles often accumulate on interior surfaces and could create an elec-

tric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operat-

ing action of this tool may cause permanent injury to fingers, hands, and arms.

Use gloves to provide extra cushion, take frequent rest periods, and limit daily time

of use.

• Direct the Dust Ejection System (DES) away from operator and coworkers.

Serious injury may result (Fig. 1, K).

• The label on your tool may include the following symbols. The symbols and

their definitions are as follows:

V ..........volts A ................amperes

Hz ........hertz W ................watts

min ......minutes ............alternating current

....direct current

n

o ..............no load speed

........Class II Construction ..............safety alert symbol

........earthing terminal …/min ........revolutions per minute

Causes and Operator Prevention of Kickback

• Kickback is a sudden reaction to a pinched, bound or misaligned wheel, wire

brush or flap disc causing an uncontrolled cut-off tool to lift up and out of the

workpiece toward the operator.

• When the wheel is pinched or bound tightly by the workpiece, the wheel stalls and

the motor reaction drives the unit rapidly back toward or away from the operator.

• Kickback is the result of tool misuse and/or incorrect operating procedures or

conditions and can be avoided by taking proper precautions as given below:

• Maintain a firm grip with both hands on the unit and position your

body and arm to allow you to resist kickback forces. Kickback forces

can be controlled by the operator, if proper precautions are taken.

• When wheel is binding, or when interrupting a cut for any reason,

release the trigger and hold the unit motionless in the material until

the wheel comes to a complete stop. Never attempt to remove the

unit from the work or pull the unit backward while the wheel is in

motion or kickback may occur. Investigate and take corrective actions

to eliminate the cause of wheel binding.

• When restarting a cut-off tool in the workpiece, check that the wheel

is not engaged into the material. If wheel is binding, it may walk up or

kickback from the workpiece as the tool is restarted.

• Support large panels to minimize the risk of wheel pinching and kick-

back. Large panels tend to sag under their own weight. Support must be

placed under the panel on both sides, near the line of cut and near the

edge of the panel.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to cause cancer, birth

defects, or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, a

nd work with approved safety equipment, such as those dust masks that are spe-

cially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,

drilling, and other construction activities. Wear protective clothing and wash

exposed areas with soap and water. Allowing dust to get into your mouth, eyes,

or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved

respiratory protection appropriate for the dust exposure. Direct particles away from

face and body.

CAUTION: Use extra care when working into a corner because a sudden, sharp

movement of the grinder may be experienced when the wheel or other accessory con-

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je DeWalt D28113 Haakse slijpmachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met DeWalt. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van DeWalt D28113 Haakse slijpmachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor DeWalt Haakse slijpmachines
Meer handleidingen voor Haakse slijpmachines

Veelgestelde vragen over DeWalt D28113 Haakse slijpmachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

DeWalt D28106 Haakse slijpmachine

Handleiding

DeWalt DWE4207 Haakse slijpmachine

Handleiding

DeWalt DWE4519 Haakse slijpmachine

Handleiding

DeWalt DCG414T1 Haakse slijpmachine

Handleiding

DeWalt DWE4217 Haakse slijpmachine

Handleiding

DeWalt D28065N Haakse slijpmachine

Handleiding

DeWalt DWE4213 Haakse slijpmachine

Handleiding

DeWalt DWE4057 Haakse slijpmachine

Gerelateerde categorieën