Handleiding DeWalt DWD115K Schroef-boormachine

Handleiding

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than

10% will cause loss of power and overheating. D

EWALT tools are factory tested; if this tool does

not operate, check power supply.

COMPONENTS (FIG. 1, 2, 3)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. Trigger switch

B. Reversing lever

C. Bubble level

D. Bubble level bulls-eye

E. Keyless chuck

Keyed chuck (not shown)

INTENDED USE

These heavy-duty V.S.R. drills are designed for professional drilling at various work sites (i.e.,

construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases.

These heavy-duty V.S.R. drills are professional power tools. DO NOT let children come into contact

with the tool. Supervision is required when inexperienced operators use this tool.

Switches (Fig. 1)

To start the drill, depress the trigger switch; to stop the drill, release the trigger.

A variable speed trigger switch (A) permits speed control—the farther the trigger is depressed, the

higher the speed of the drill.

NOTE: Use lower speeds for starting holes without a center punch, drilling in metal or plastics,

driving screws or drilling ceramics. Higher speeds are better for drilling wood and composition

boards and using abrasive and polishing accessories.

The reversing lever (B) is used for withdrawing bits from tight holes and removing screws. It is

located above the trigger switch. To reverse the motor, release the trigger switch FIRST and then

push the lever to the right. After any reversing operations, return lever to forward position.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Drilling

WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored

or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the

material.

1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole

saws. For METAL, use steel twist drill bits or hole saws. For MASONRY, such as brick, cement,

cinder block, etc., use carbide-tipped bits rated for percussion drilling.

2. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting,

but do not push hard enough to stall the motor or deflect the bit.

3. Hold tool firmly with both hands to control the twisting action of the drill.

4. IF DRILL STALLS, it is usually because it is being overloaded or improperly used. RELEASE

TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO

NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL —

THIS CAN DAMAGE THE DRILL.

5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit

through the last fractional part of the hole.

6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow

speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep

enough to drill without the bit skipping out.

DRILLING IN METAL

Start drilling with slow speed and increase to full power while applying firm pressure on the tool.

A smooth even flow of metal chips indicates the proper drilling rate. Use a cutting lubricant when

drilling metals. The exceptions are cast iron and brass which should be drilled dry.

NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in steel can be made easier if a pilot hole [5/32"

(4 mm) to 3/16" (5 mm)] is drilled first.

DRILLING IN WOOD

Start drilling with slow speed and increase to full power while applying firm pressure on the tool.

Holes in wood can be made with the same twist drills used for metal. These bits may overheat

unless pulled out frequently to clear chips from the flutes. Work that is apt to splinter should be

backed up with a block of wood.

DRILLING IN MASONRY

When drilling in masonry, use carbide-tipped bits rated for percussion drilling and be certain that

the bits are sharp. Use a constant and firm force on the tool to drill most effectively. A smooth, even

flow of dust indicates the proper drilling rate.

Bubble Level (Fig. 2)

Your drill is equipped with a bubble level (C) that assists you in drilling level holes.

For horizontal drilling, tilt the drill up or down as required so that the bubble floats in the center of

the parallel lines drawn on the glass. When the bubble is centered between the lines, the drill is level.

For vertical drilling, align the drill so that the bubble floats in the center of the bull’s-eye (D).

To assure accuracy, first place a level on your work piece and position it so that it is level. Then,

when the drill reads level, the two will be aligned. (Any bubble level can only indicate level to the

earth’s surface).

NOTE: The fluid in the bubble level vial is mineral spirits. If the mineral spirits gets into your eyes,

flush eyes with water. If irritation occurs, seek medical attention. If the vial fluid comes into contact

with your skin, remove contaminated clothing and remove excess fluid. Rinse thoroughly with water

followed by washing with soap and water. If irritation occurs, seek medical attention. If vial fluid is

inhaled, immediately get fresh air. If difficulty breathing, seek medical attention.

Keyless Chuck (Fig. 3)

Your tool features a keyless chuck (E) for greater convenience. To insert a drill bit or other accessory,

follow the steps listed below.

1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the front

half counterclockwise, as shown in Figure 3. Rotate far enough so that the chuck opens

sufficiently to accept the desired accessory.

2. Insert the bit or other accessory about 3/4" (19 mm) into the chuck and tighten securely by

holding the rear half of the chuck and rotating the front portion in the clockwise direction. When

the chuck is nearly tightened, you will hear a clicking sound. After 4–6 clicks, the chuck is

securely tightened around the accessory.

3 To release the accessory, repeat step 1 listed above.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part

of the chuck and turning the tool on. Damage to the chuck and personal injury may result.

KEYLESS CHUCK REMOVAL (FIG. 4)

Tighten the chuck around the shorter end of a hex key (not supplied) of 1/4" (6 mm) or greater size.

Using a soft hammer or piece of wood, strike the longer end in the counterclockwise direction. This

will loosen the chuck so that it can be unscrewed by hand.

KEYLESS CHUCK INSTALLATION (FIG. 5)

Screw the chuck on by hand as far as it will go. Tighten the chuck around the shorter end of a

1/4" (6 mm) or larger hex key (not supplied) strike the longer end in the clockwise direction with a

soft hammer.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power

source before installing and removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

FIG. 5

FIG. 4

FIG. 2

C

D

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing

this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

Motor Brushes

DEWALT uses an advanced brush system which automatically stops the drill when the brushes

wear out. This prevents serious damage to the motor. New brush assemblies are available at

authorized D

EWALT service centres. Always use identical replacement parts.

Lubrication

When the tool is taken apart for motor brush replacement a small amount of grease should be

added (or redistributed from that remaining in housing) to the gears. The ball bearings used in this

tool are lubricated during manufacture and require no lubrication.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by a D

EWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always use identical replacement

parts.

Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,

only D

EWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or

authorized service center. If you need assistance in locating any accessory, please contact D

EWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D

EWALT (1-800-433-

9258) or visit our website: www.dewalt.com.

CAUTION: To reduce the risk of injury, the following accessories should be used only in sizes up

to the maximums shown in the table below.

MAXIMUM RECOMMENDED CAPACITIES

Drill capacity 3/8" (10 mm)

R.P.M. 0-2500

Bits, metal drilling 3/8" (10 mm)

Wood, flat boring 1" (25.4 mm)

Bits, masonry drilling 1/2" (12.7 mm)

Hole saws 1-1/8" (28.4 mm)

ACCESSORY MUST BE RATED FOR USE AT SPEED EQUAL TO OR HIGHER THAN NAMEPLATE

R.P.M. OF TOOL WITH WHICH IT IS BEING USED.

Wire wheel brushes 4" (101.6 mm) diameter maximum

Wire cup brushes 3" (76.2 mm) diameter maximum

Buffing wheels 3" (76.2 mm) diameter maximum

Rubber backing pads 4-5/8" (117.4 mm) diameter maximum

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-D

EWALT (1-800-433-9258). This warranty does not apply to accessories or

A

B

FIG. 1

FIG. 3

E

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je DeWalt DWD115K Schroef-boormachine. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met DeWalt. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van DeWalt DWD115K Schroef-boormachine in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor DeWalt Schroef-boormachines
Meer handleidingen voor Schroef-boormachines

Veelgestelde vragen over DeWalt DWD115K Schroef-boormachine

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

DeWalt DW989 Schroef-boormachine

Handleiding

DeWalt DCD791B Schroef-boormachine

Handleiding

DeWalt DCD703F1 Schroef-boormachine

Handleiding

DeWalt DC756 Schroef-boormachine

Handleiding

DeWalt DCD776 Schroef-boormachine

Handleiding

DeWalt DW980 Schroef-boormachine

Handleiding

DeWalt DCD708C2 Schroef-boormachine

Handleiding

DeWalt DC989KA Schroef-boormachine

Gerelateerde categorieën