Handleiding DLS Ultimate UR 2.5 Autoluidspreker

Handleiding

Welcome

Thank you for buying a DLS Ultimate speaker.

This manual will show you how to do a correct installation. Please

read the entire manual before beginning the installation. Install

the speakers yourself if you feel confident with our instructions

and if you have the proper tools. The ULTIMATE speakers are

our best speaker line but a poor installation job can destroy the

final result even from these speakers. So if you feel unsure,

turn over the installation job to someone better suited to it.

Installation

The speakers should be installed high up in the door side or in

the dashboard. These speakers doesn’t require any box.

When the midrange is mounted high up on the dashboard the

mid level creates a frequency peak in some vehicles. If so use

the low ”mid level” in the filter box. If the level is still too high,

connect a 3-5 ohm resistor in series with the + feed. We

recommend you to install them in a strong baffle of MDF-

board or similar. A strong baffle will improve the sound quality.

If you don’t have the possibility of doing strong baffles you

must use the steel rings coming with the drivers to improve

the stability of the mounting.

Wiring

Use high quality speaker cables like DLS HQS or similar.

Avoid using the factory pre-installed cabling, they will not give

the sound reproduction that you should expect from these

high class speakers.

Make sure the cables don’t get jammed causing a short circuit

to ground. This can damage the output circuits of your head

unit or amplifier.

Connect the cables with correct polarity to the speakers.

Observe the markings on the terminals. The red marked

terminal is plus and the black is minus.

UP 2.5 / UP2.5i

UP 2.5B

UR 2.5

Iridium 3

Technical data UP 2.5 / UP 2.5i / UP 2.5B

Break-in period

Allow the speakers to play at normal volume for at least 15-20

hours. After this time the performance is correct.

Technical Assistance

For technical assistance ask the shop where the product was

sold or the distributor in your country.

You can also send an e-mail to [email protected]

Information can also be found on our web-site www.dls.se

We follow a policy of continuous advancement in development.

For this reason all or part of specifications & designs may be

changed without prior notice.

Warranty service

This speaker is covered by warranty, depending on the

conditions in the country where it is sold. If the speaker is retur-

ned for service, please include the original dated receipt (or a

copy) with the product.

DLS ULTIMATE

MIDRANGE SPEAKERS

DLS Svenska AB

P.O. Box 13029

SE-40251 Göteborg, Sweden

Tel: +46 31 840060

Fax: +46 31 844021

E-mail: [email protected]

www.dls.se

Size 2,5" ( 6,3 cm)

Nom. power (RMS) 90 Watts RMS

Maximum power 160 Watts

Frequency range 400 Hz-8000 Hz

Rec. frequency use for 500 Hz - 5000 Hz

active crossover Use HP 18-24 dB slope /oct.

Sensitivity 91 dB / W / m

Resonanst freq. / Fs 490 Hz

Magnet diameter 65 mm / 2,56”

Outer diameter 100 mm / 3,94”

Installation depth 15 mm / 0,59”

Mounting hole 82 mm / 3,23”

Cone Doped fabric

Voice coil 52 mm / 2” al. flat wire

Technical data UR 2.5

Size 2,5" ( 6,3 cm) with rear chamber

Nom. power (RMS) 90 Watts RMS

Maximum power 160 Watts

Frequency range 400 Hz-8000 Hz

Rec. frequency use for 500 Hz - 4500 Hz

active crossover Use HP 18-24 dB slope /oct.

Sensitivity 91 dB / W / m

Resonanst freq. / Fs 430 Hz

Magnet diameter 65 mm / 2,56”

Outer diameter 100 mm / 3,94”

Installation depth 26 mm / 1,02”

Mounting hole 82 mm / 3,23”

Cone Doped fabric

Voice coil 52 mm / 2” al. flat wire

Technical data Iridium 3

Size 2,5" ( 6,3 cm) with rear chamber

Nom. power (RMS) 100 Watts RMS

Maximum power 160 Watts

Frequency range 250 Hz-8000 Hz

Rec. frequency use for 400 Hz - 4500 Hz

active crossover Use HP 18-24 dB slope /oct.

Sensitivity 91 dB / W / m

Resonanst freq. / Fs 280 Hz

X-max +- 0,5 mm

Magnet diameter 80 mm / 3,15”

Outer diameter 120 mm / 4,72”

Installation depth 35 mm / 1,38”

Mounting hole 95 mm / 3,74”

Cone Doped fabric

Voice coil 75 mm / 3” al. flat wire

Crossover

The speakers must be used with either a passive or an active

filter in a 3-way configuration. If you can’t use active filters you

can build your own passive filter like in this example. It is a 6/6

dB slope band pass filter ~500 - 4500 Hz

This rather simple passive filter can be used for UP2.5 / UR2.5.

Iridium 3 should only be used in active crossover mode. Use

polypropylene capacitor and low-resistance air coil. The resistor

is used to adjust the level. The 4,7 omhs is a standard value

but you must find a resistor value that matches the sensitivity

of the other speakers in your system. In some configurations

you don’t have to use a resistor at all.

12

μμ

μμ

μF 0,25 mH

+

-

4,7

ΩΩ

ΩΩ

Ω

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je DLS Ultimate UR 2.5 Autoluidspreker. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met DLS. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van DLS Ultimate UR 2.5 Autoluidspreker in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor DLS Autoluidsprekers
Meer handleidingen voor Autoluidsprekers

Beoordeling

Gerelateerde producten

Handleiding

DLS Ultimate Iridium 3 Autoluidspreker

Handleiding

DLS Ultimate UP 2.5 Autoluidspreker

Handleiding

DLS Performance MC6.2 Autoluidspreker

Handleiding

DLS Performance M6.2 Autoluidspreker

Handleiding

DLS Performance MB6.2 Autoluidspreker

Handleiding

Sony XS-FB133E Autoluidspreker

Handleiding

Sony CXS-GT2313 Autoluidspreker

Handleiding

Sony XS-GF1022X Autoluidspreker

Gerelateerde categorieën