Handleiding Eureka Timberline SQ Outfitter Tent

Handleiding

REV. A 10-.09

Take down: Pull up stakes and stow. Remove the fly. Un-clip the tent from the poles. Pull poles out

of the grommets, collapse the poles and stow in the bag. Fold the tent and fly. Lay the fly on the

folded tent along with the bag of poles. Roll up all and stow in the carry bag.

Optional: Add durability and versatility to your tent with our “Lite-Set” Footprint. It’s made of the

same fabric as the tent's floor: complete with web loops, grommets, and side release buckles. The

Footprint, in combination with the fly and poles creates a lightweight, compact basic shelter. This

option reduces the carry weight by more than 25%.

Assembly Instructions

Timberline SQ Outfitter

fig.2

fig.3

fig.1

fig.4

fig.5

fig.6

fig.10

fig.11

fig.12

Component List: 1 Tent Body, 1 Tent Fly, 6 Part Frame Assembly, 1 Carry Bag,

1 Stake Bag with Stakes & Guy lines, 1 Pole Bag, 1 Pole Repair Splint

NOTE: Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to

get the tent out. These actions may cut the shock cord and/or damage the pole ends.

1. Unroll and unfold the tent and lay it on the

ground. In windy conditions, stake down one

front corner into the wind.

See fig.1.

3. Fit the posts into the webs:

There are grommeted webs sewn to each

corner of the tent. Start at either end and working

you way around the tent, insert the posts into the

grommets. See fig. 3 & 4.

4. Raise the frame: Start at

either end and insert the ridge

pole into the hub sleeve labeled

EUREKA!. Walk to the opposite

end and grasp both the ridge pole

and the second hub. Push/curve the

poles until the ridge pole fits securely into the

second hub. See fig. 5 & 6.

11. At each corner, attach the web buckles from the fly, to

their mates on the tent web. Pull the web to adjust tension as

needed. See fig.14.

12. Stake down the fly: Use the silver skewers to stake through

the web loops on the vestibule/door. At each side of the fly, tie

guy out lines to the two rings and stake these down also.

Important: Use the slider to adjust tension.

For proper ventilation, the fly must

not lay against the tent.

See fig.15 & 16.

Your tent is ready!

7. Stake the tent down: The tent is now freestanding. Move it

to your desired location. Use the yellow stakes and drive them

down through the corner web loops.

Stake diagonally opposite corners

while applying tension to

smooth the floor wrinkles

and square the tent.

See fig.10.

10. Attach the extensions to the ridge pole hub: Fit one of the

ridge extension poles into the hub and into the rod pocket at the

edge of the fly. Grasp the top and pivot forward to seat. Repeat

at other end of the tent. See fig. 13.

9. Attach the fly to the

spreader pole: Reach under

the fly at the middle near the

roof. Locate the sewn on

pocket and slide it over the

pocket end of the spreader

pole. Repeat at the other

end. See fig. 12.

2. Join the frame sections on the ground:

Fit each pole to its mate or hub. The sections

are shockcorded. It is important to make sure that

each section has firmly seated into the hub. Improperly

fit poles may cause the hub to break.

Set the “A” frames over the tent so that the poles align to the tent corner webs

and the hub sleeve labeled EUREKA! is pointing toward tent center.

See fig. 2 & 3.

8. Attach the fly to the tent: Drape

the fly over the top of the tent. Pull

the fabric out and over the hubs

and out and over the spreader.

The fly fits either way. Align the

webs on the fly to the webs

on the tent corners.

See fig. 11.

fig.13

fig.16

fig.15

fig.14

“A” Frames

Repair

Splint

Ridge Pole

Ridge Extensions

Spreader Pole

fig.7

fig.8

6. Install the spreader pole: The spreader pole fits

across the top, over and perpendicular to the ridge

pole. There are two pockets sewn to the top of the

tent body. Fit the poles into these pockets. It is

easier if you slide the pole

into a pocket first and then

push it over to the other

side. See fig. 8.

Then, work your way down

and across the frame,

attaching the pole clips as

you go. See fig. 9 & 10.

5. Attach the tent body to the frame: There are two

types of connectors sewn to the tent body. For the

first, hang the two end shockcords onto the

stand-offs on the hubs. See fig. 7

fig.9

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Eureka Timberline SQ Outfitter Tent. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Eureka. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Eureka Timberline SQ Outfitter Tent in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Eureka Tenten
Meer handleidingen voor Tenten

Veelgestelde vragen over Eureka Timberline SQ Outfitter Tent

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Gerelateerde producten

Handleiding

Eureka N!ergy 9 Tent

Handleiding

Eureka Midori 3 Tent

Handleiding

Eureka N!ergy 1210 Tent

Handleiding

Eureka Sunrise EX 8 Tent

Handleiding

Eureka Taron 2 Tent

Handleiding

Eureka Timberline SQ XT Tent

Handleiding

Eureka Condo Tent

Handleiding

Eureka Suite 6 Tent

Gerelateerde categorieën