Handleiding Foundations 100-SSC-SM Commode

Handleiding

2

Recommended Blocking:

Wood double stud blocking is necessary. Contact an architect

and building official to make sure the blocking is adequate and

complies with building codes (Fig. a).

1. Remove and discard Truss Head Spanner screws from unit back (Fig. b).

2. Locate wood stud where left side of changing station will be mounted to

the wall.

3. For A. D. A. compliance, measure up 45” (114 cm) from the floor and mark

the wall. This locates the position for the top left attachment hole.

NOTE: Mark on wall MUST be in center of wood stud.

4. Lay top section of changing station down on changing station bed (Fig. c) and

align hole in top left corner of changing station with mark on wall and hold in place.

5. Using a level and measuring tape, mark the remaining three (3) holes. After marking

holes, set changing station down on ground.

6. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require

2 people.

NOTE 1: For wood studs:

- If finished wall surface is tile or masonry over wood studs, use

a 7/32” masonry bit for the pilot hole until you hit the wood

stud, then change to 1/8” bit.

- Use wood screws, finishing washers and flat washers (Fig. d).

NOTE 2: For use with toggle anchors:

- If finished wall surface has wood studs that are not 16” on center,

has metal studs, or has an underlying surface of concrete block,

use 1/2” bit.

- Use machine screws and flat washers (Fig. e).

- For holes NOT located in a wood stud, toggle anchors MUST be

used (Fig. f). See “Using Toggle Anchors” section.

7. Rotate plastic top section back up so that mounting hardware goes through

the plastic as well as the metal back (Fig. b).

NOTE: This unit incorporates a finishing collar that seats behind the changer’s

outside flange. Center the collar as the unit is being tightened against the wall

(Fig. g).

8. Align holes in changing station with drilled holes and secure top left corner of changing

station to wall stud using the appropriate screw and washer. Continue to secure the

three (3) remaining corners using the appropriate screws and washers as described

in Note 1 or Note 2.

INSTALLATION

Fig. b

Truss Head

Spanner Screws

Fig. c

Surface-Mount

Holes

Fig. d

Fig. e

Fig. f

Toggle

Anchor

Flat

Washer

Machine

Screw

Changing

Station

Changing

Station

Finishing

Washer

Wood

Screw

Wood Stud

Wood Stud

Flat

Washer

8

1

/

4

(

2

1

0

m

m

)

o

n

c

e

n

t

e

r

3

2"

(813 mm)

o

n center

T

op

F

or A. D. A.

C

ompliance

45”

(114 cm)

A

. F. F

Fig. a

Fig. g

Collar

Unit

Wall

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Foundations 100-SSC-SM Commode. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Foundations. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Foundations 100-SSC-SM Commode in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Foundations Commodes
Meer handleidingen voor Commodes

Beoordeling

Gerelateerde producten

Handleiding

Foundations 100-SSE Commode

Handleiding

Foundations 100-SS Commode

Handleiding

Foundations 100-SSC-R Commode

Handleiding

Foundations 103-BQS Commode

Handleiding

Foundations 100-SSV Commode

Handleiding

Foundations 100-EV Commode

Handleiding

Foundations 100-EVBP Commode

Handleiding

Foundations 100-EH Commode

Gerelateerde categorieën