Handleiding Futaba FP-9VAP RC Controller

Handleiding

Fail Safe and Hold General Instructions

Fail Safe

• F/S or HOLD can be selected for each channel

(1

to

8).

• Channels selected for HOLD will remain in

HOLD

until

a

normal

signal

resumes. Those

selected for F/S will move to their pre-set posi-

tions after 1 second of signal interruption.

• F/S SET simultaneously stores the desired Fail

Safe position in the transmitter memory and

sends it to the receiver.

•The

F/S

data

is

automatically

sent

to

the

receiver when the transmitter is first turned ON

and at one minute intervals as long as the trans-

mitter is left on.

• The F/S position can be checked with the

CHK program key.

• Only the Throttle

channel (CH3) can be set for

Battery Fail Safe.

Fail Safe Setting

1) Display the EDIT screen, then select the

FAILSAFE screen by pressing the F/S pro-

gram key.

2) Move

the

cursor

to the desired channel with

the

and

cursor keys and select

HOLD or F/S for each channel by pressing the

or program key. When Failsafe is

selected, the number 50 will appear below the

appropriate channel on the POSI-(%) line of

the FAILSAFE screen.

3) Store the Failsafe positions in the transmitter

Battery Fail Safe Setting

1) Set the Failsafe position on the throttle chan-

nel (CH3) as described above. A position

slightly above the minimum engine idle speed

is recommended.

2) BFS

Release Point Setting (When

THR is

designated as the release channel)

• Move the cursor to the B/FS-RESET line

of

the FAILSAFE screen with the

cursor key.

•

Select the BFS

release

channel

with

the

or program key.

• Set the throttle stick to the desired

BFS

release

point

and

press

the program

key. This designates CH3 (Throttle) as the

release channel and sets the stick release

point

simultaneously.

3) To release BFS by the CH9 switch, press the

program key.

•

BFS

can

be

released

by the CH9 switch

only

when the switch is moved to the upper

position. If the CH9 switch is in the lower

position, BFS cannot be released.

• In the BFS release state, the characters 0%-

RESET are displayed on the B/FS-RESET

line of the FAILSAFE screen.

4) If Battery Fail Safe is not desired, press the

program key (when the cursor is on the

B/FS-RESET line). The BFS

function

will

then be disabled.

memory by pressing the

key while hold-

ing the stick or lever of the channel being set

in the desired Failsafe position. Simultaneous-

ly, the data is also transmitted to the receiver

and is automatically re-transmitted at one

minute intervals.

In the example below, (Throttle) was set to Fail Safe and Battery Fail Safe.

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Futaba FP-9VAP RC Controller. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Futaba. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Futaba FP-9VAP RC Controller in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Futaba RC Controllers
Meer handleidingen voor RC Controllers

Beoordeling

Gerelateerde producten

Handleiding

Futaba FP-5UAP RC Controller

Handleiding

Futaba FP-4FN RC Controller

Handleiding

Futaba FP-8SSAP RC Controller

Handleiding

Futaba 6EXAP RC Controller

Handleiding

Futaba FP-8JN RC Controller

Handleiding

Futaba 10CHG RC Controller

Handleiding

Futaba FP-7G RC Controller

Handleiding

Futaba 12K RC Controller

Gerelateerde categorieën