Handleiding Futaba FP-9VAP RC Controller

Handleiding

BATTERY CHARGING INSTRUCTIONS

(Transmitter and Receiver Nicd Batteries)

Before operating your system, recharge the Nicd batteries as follows:

•Connect the DIN connector of the FBC-8B (2)

battery charger to the transmitter charging

socket, and connect the 3P connector to the

airborne NR-4J Nicd battery pack and plug the

battery charger into a 120VAC outlet as shown

in the figure.

•The TX and RX LEDs light to show that bat-

teries are being charged. The Nicd batteries can

also be charged through the DSC-CHG cord by

connecting the CHG adaptor to the charger as

shown in the figure. This allows the NR-4J

airborne Nicd pack to be charged without

removing it from the model.

•Normally recharge the battery for about 15

hours. If it has not been used for some time,

discharge and recharge it two or three times,

then charge it a full 15 hours.

•The

amount of time

remaining

before the bat-

teries must be recharged can be estimated by

checking the integrated timer at the moment

the TX battery alarm sounds (antenna ex-

tended).

• Leaving batteries in the discharged state for a

long time will adversely affect their capacity

and life.

•The TX and RX Nicd batteries can be charged

simultaneously or independently.

•A fully-charged TX battery can be used for

about 10 flights of 10 minutes each. The air-

borne NR-4J Nicd battery pack can be used

for about 7 flights when 6 servos are used and

about 4 flights when 10 servos are used.

• The DSC (Direct Servo Controller)

system connects the signals from

the transmitter directly to terminal

C of the receiver through the DSC

cord and controls the servos with-

out transmitting radio waves. \\ is

extremely convenient when other

dyers are on the same frequency,

or during contests, etc.

•When the DIN connector of the

DSC cord is connected to the DSC

socket, the power to the encoder of

the transmitter is turned ON auto-

matically The transmitter power

switch is left OFF.

• When not using the DSC, discon-

nect the DIN connector to reduce

battery drain.

• To operate the servos, turn on the

airborne switch (only).

•When the DSC cord

is connected, the receiver

power supply voltage

is measured

(no load).

The voltage is displayed

by "Ex" on the lower

right side of the initial

LCD

screen.

NR-4J

Male

Female

DSC-CHG cord

Male

Female

Cut Here.

Male

Female

Male

Female

CHG

Adaptor

Female

Install the

accessory

DSC-CHG cord

(connector with tab)

to the side of

the aircraft fuselage

to use the charging

and DSC socket.

Charging

socket

and

DSC

connector

Female

Female

Receiver

DSC Cord

Make this connection

when using the DSC.

RX (Receiver)

TX (Transmitter)

AC-120V

Charger FBC-8B (2)

Charging Method

[6]

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Futaba FP-9VAP RC Controller. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Futaba. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Futaba FP-9VAP RC Controller in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Futaba RC Controllers
Meer handleidingen voor RC Controllers

Beoordeling

Gerelateerde producten

Handleiding

Futaba FP-5UAP RC Controller

Handleiding

Futaba FP-4FN RC Controller

Handleiding

Futaba FP-8SSAP RC Controller

Handleiding

Futaba 6EXAP RC Controller

Handleiding

Futaba FP-8JN RC Controller

Handleiding

Futaba 10CHG RC Controller

Handleiding

Futaba FP-7G RC Controller

Handleiding

Futaba 12K RC Controller

Gerelateerde categorieën