Handleiding GE TFT26PRDAAA Koel-vries combinatie

Handleiding

PREPARATION

Clearances Refrigerator Location

Allow the following clearances for ease of installation, proper air

circulation and plumbing and electrical connections:

Sides.......................................................................16 mm (5/8″)

Top.............................................................................25 mm (1″)

[If built-in, allow 22 mm (7/8″) for hinge covers.]

Back...........................................................................25 mm (1″)

If the refrigerator is against a wall on either side, allow the

following clearances:

For models up to and including 26, allow 19 mm (3/4″) for door

clearance.

If the model has a Refreshment Center allow 66 mm (2

5

⁄

8

″) for the

Refreshment Center side door.

For 27 models, allow 38 mm (1

1

⁄

2

″) for door clearance.

If the model has a Refreshment Center allow 89 mm (3

1

⁄

2

″) for the

Refreshment Center side door.

Do install it on a floor strong enough to support a fully

loaded refrigerator.

Care and Cleaning Preparation

When You Go on Vacation When You Move

For extended vacations or absences, shut off the power to the

refrigerator, move the fresh food control to the “ ” position, and

clean the interior with a baking soda solution of 15 ml (1 tablespoon)

of baking soda to one liter (1 quart) of water. Wipe dry. To prevent

odors, leave an open box of baking soda in the refrigerator. Leave

doors open.

Move icemaker feeler arm to (up) position, which stops

icemaking, and be sure to shut off water supply to the refrigerator.

For shorter vacations, remove perishable foods and leave

controls at regular settings. However, if room temperature is

expected to drop below 16°C (60°F), follow the same instructions

as for extended vacations.

Disconnect power cord from wall outlet, remove all food, and clean

and dry the interior.

Secure all loose items such as grille, shelves and storage pans by

taping them securely in place to prevent damage.

Be sure refrigerator stays in upright position during actual moving and

in van. Refrigerator must be secured in van to prevent movement.

Protect outside of refrigerator with blanket.

Rollers

Adjustable rollers behind the base grille enable you to move the

refrigerator away from the wall for cleaning. These rollers should be

set so that the refrigerator rests firmly on the floor. To assure that the

doors will close automatically from a halfway-open position, there is a

built-in tilt from the front to the back of the cabinet. Side-by-side

refrigerators also have specially designed door hinges that lift both

doors slightly when opened, allowing the force of gravity to help close

them securely.

To adjust rollers, remove the base grille by

grasping it at the bottom and pulling it out.

Turn roller adjusted screws clockwise to

raise refrigerator, counterclockwise to lower

it. Use adjustable wrench (3/8″ hex head bolt)

or pliers.

When adjusting front rollers for proper door closure, we recommend

that the bottom front edge of the cabinet be approximately 16 mm

(5/8″) from the floor.

To replace the base grille, align

prongs on back of grille with clamps

in cabinet and push back until the grille

snaps into place.

Water Supply to Icemaker (on some models)

If your refrigerator has an icemaker, or if you plan to add an

icemaker later, the icemaker will have to be connected to a cold

drinking (potable) water line.

A water supply kit containing copper tubing, shutoff valve, fittings

and instructions is available at extra cost from your dealer. There

should be sufficient tubing from the cold water supply to the

icemaker inlet to allow moving the refrigerator out from the wall

several feet [approximately 2.5 m (8′) of 1/4″ copper tubing in three

25 cm (10″) diameter coils].

Do not use kits with plastic tubing since there is water pressure in the

supply line at all times.

Maximum permissible inlet water pressure—8.3 bars (120 p.s.i.).

Minimum permissible inlet water pressure—1.4 bars (20 p.s.i.).

Installation of icemaker must be made by a qualified service technician.

(continued next page)

15

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je GE TFT26PRDAAA Koel-vries combinatie. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met GE. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van GE TFT26PRDAAA Koel-vries combinatie in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor GE Koel-vries combinaties
Meer handleidingen voor Koel-vries combinaties

Veelgestelde vragen over GE TFT26PRDAAA Koel-vries combinatie

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.

Beoordeling

Gerelateerde producten

Handleiding

GE PSE25KYHFS Koel-vries combinatie

Handleiding

GE PTQ470SAMR Koel-vries combinatie

Handleiding

GE GFE26JYMFS Koel-vries combinatie

Handleiding

GE TBX16DPERAD Koel-vries combinatie

Handleiding

GE GTS22KYNRFS Koel-vries combinatie

Handleiding

GE TBX18BADGRAA Koel-vries combinatie

Handleiding

GE GNE25JYKFS Koel-vries combinatie

Handleiding

GE PYE18HYRKFS Koel-vries combinatie

Gerelateerde categorieën