Handleiding Halstead Ace HE 30 CV-ketel

Handleiding

The Halstead Ace HE24, HE30 and HE35 are high efficiency condensing,

fully automatic, wall mounted gas appliances for use with natural gas.

The appliances incorporate a microprocessor based, fully modulating pre-mix gas

control system with direct burner ignition.

The Ace HE24 provides central heating at outputs between 6.0 kW (20,500

Btu/h) and 18.0 kW (61,500 Btu/h) and domestic hot water at outputs between

6.0 kW (20,500 Btu/h) and 24.0 kW (82,000 Btu/h).

The Ace HE30 provides central heating at outputs between 7.2 kW (24,600

Btu/h) and 23.1 kW (78,900 Btu/h) and domestic hot water at outputs between

7.2 kW (24,600 Btu/h) and 30.0 kW (102,400 Btu/h).

The Ace HE35 provides central heating at outputs between 8.3 kW (28,300

Btu/h) and 24 kW (81,900 Btu/h) and domestic hot water at outputs between

8.3 kW (28,300 Btu/h) and 35 kW (119,400 Btu/h).

Heat output is controlled according to demand (in both domestic hot water and

central heating modes) by the fully modulating pre-mix burner control. The

appliance always gives priority to domestic hot water supply. The appliance

incorporates frost protection. However this is not operational when the main

electrical supply to the appliance is isolated. An electro/mechanical 24hr time

clock is fitted as standard.

Gas Consumer Council: The Gas Consumer Council (GCC) is an

independent organization which protects the interests of gas users. If you need

advice, you will find the telephone number in your local directory under 'Gas'.

2

SAFETY

Read these instructions and the user label (fitted on the boiler front panel)

carefully before attempting to operate the appliance. Comply with all

applicable warnings.

Do not interfere with any sealed components

and use the appliance only in accordance with these instructions.

CURRENT GAS SAFETY (INSTALLATION AND

USE) REGULATIONS OR THE RULES IN FORCE.

It is the law that all gas appliances are installed by a competent person in

accordance with the above regulations. Failure to install appliances

correctly could lead to prosecution. It is in your own interest, and that of

safety, to ensure that the law is complied with. If the appliance is

damaged, turn off the appliance and consult a CORGI registered installer.

If it is known or suspected that a fault exists on the appliance it MUST

NOT be used until the fault has been rectified by a competent person.

2.2

ELECTRICAL SUPPLY

This appliance must be earthed.

Supply: 230V - 50Hz fused at 3A.

The method of connection to the mains supply must facilitate complete

isolation of the appliance. Either a 3A fused three pin plug and

unswitched shuttered socket outlet, or a 3A fused double pole switch

having a 3 mm contact separation in both poles, serving only the boiler

(and its external controls), may be used.

2.3

CLEARANCES AND VENTILATION

It is not necessary to have a purpose provided air vent in the room or

internal space in which a room-sealed appliance is installed. Cupboard or

compartment ventilation is not necessary for a room-sealed appliance

providing that the minimum clearances are maintained.

Where an open flued (B23) system is used (for example KIT E 'Chimney

flue liner kit') then an air vent must be provided in the same room or

internal space as the flue duct air inlet with a minimum free-area as stated

in section 3.4 of the boilers installation manual.

4

HOT WATER OPERATION

On a demand for DHW, water flow is detected and the ignition sequence

initiated. The fan and pump will start and the boiler will light.

If the DHW draw off rate is high (over 10l/min.), the appliance will run

continuously at full output until the tap is either turned off, or the flow rate is

reduced, in which case the heat supplied will reduce accordingly to

maintain a steady temperature (55°C max).

Hot water is made available at the appliance outlet almost immediately, but

the final temperature and time taken for the hot water to reach a tap

depends upon the rate at which water is drawn off and the length of the

pipe runs between the boiler and taps.

When the tap is turned off, the appliance after a short period of time will

revert to heating mode if there is a demand. Otherwise the burner will be

extinguished until the next demand for hot water.

1

INTRODUCTION

3

BOILER LOGBOOK

Please ensure that you have a Logbook supplied with your appliance. This

Logbook should be completed by your installer to verify that the correct

installation and commissioning procedure was followed.

Failure to complete the Logbook may result in difficulties should a problem

arise with your appliance during the guarantee period.

This Logbook forms part of the industry's Benchmark code of practice for the

installation, commissioning and servicing of central heating systems. All

CORGI Registered Installers carry a CORGI ID card and have a registration

number. Both should be recorded in your Logbook. You can check your

installer is CORGI registered by calling CORGI on 0870 401 2230.

2.1

5

OPERATING INSTRUCTIONS

Refer to Fig. 1

1) Switch on the electrical supply.

If heating is required, ensure that the clock is set to an ON period (see

diagram) or set the clock over-ride switch to the ON position. Turn up the

room thermostat (if fitted).

2) Turn the control knob to the midpoint between minimum and maximum

setting. The digital display changes from '

o

' to '

c

'.

3) When the burner has lit the digital display changes to '

C

' to indicate heating

ON and a small dot will appear in the bottom right corner of the display.

4) Hot water will be supplied as soon as any Domestic Hot Water tap is

turned on and the digital display will change to '

H

' to indicate hot water is

being supplied. A small dot will appear in the bottom right corner of the

display.

5) If the burner fails to light the fan will stop. Initially this may be due to air in

the gas supply. The boiler will automatically have five attempts at ignition.

After the five attempts it may be necessary to RESET the boiler by turning

the control knob fully anti-clockwise to the RESET position and repeat from

step 3.

6) If the digital display reads ‘ ’ it is an indication that the heating or hot

water mode is satisfied, and the boiler is performing a pump over-run

function. This is perfectly normal.

After a hot water draw off the burner may stay on for

a few seconds (see clause 5.8 'Keep hot facility' in

the installation manual)

Priority is always given to Domestic Hot Water supply.

TO LIGHT THE BOILER IN CENTRAL

HEATING MODE

5.1

Beoordeling

Meer over deze handleiding

We begrijpen dat het prettig is om een papieren handleiding te hebben voor je Halstead Ace HE 30 CV-ketel. Je kunt de handleiding bij ons altijd downloaden en daarna zelf printen. Indien je graag een originele handleiding wilt hebben, raden we je aan contact op te nemen met Halstead. Zij kunnen wellicht nog voorzien in een originele handleiding. Zoek je de handleiding van Halstead Ace HE 30 CV-ketel in een andere taal? Kies op de homepage je taal naar keuze en zoek daarna op het modelnummer om te zien of we deze beschikbaar hebben.

Specificaties

Alle handleidingen voor Halstead CV-ketels
Meer handleidingen voor CV-ketels

Veelgestelde vragen over Halstead Ace HE 30 CV-ketel

Ons supportteam zoekt dagelijks naar nuttige productinformatie en antwoorden op veelgestelde vragen. Als er onverhoopt toch een onjuistheid tussen onze veelgestelde vragen staat, laat het ons dan weten via het contactformulier.